How to turn plastic waste into diesel fuel cheaply

[jonathan]

pyrolysis fuel types

thanks all of you l work on my burner today l have bigger flame now.some more work and try again thanks alot

[Excalibur]

Jonathan, BB has touched on a very cheap, affordable solution for your needs. DIY refractory firebrick.
I suggest to Google the topic: How to make refractory brick, Homemade Castable Refractories, DIY fireclay, etc. Also BB has done a lot of testing of various affordable solutions. See pyrolysis section at BB website.

Two types of firebrick for consideration is the dense firebrick and the porous firebrick. The dense one is known for being a storage of heat while the porous lightweight one will be an insulator and not store heat well at all.
Porous firebrick can be made by adding organic or combustible material to the brick recipe which burns out during firing. This makes for thousands of tiny air pockets throughout the brick.
Hope this helps.

[jonathan]

retort problem

woww soo thanks l will google it and check bb website thanks all

[Beyond Biodiesel]

Jonathan, BB has touched on a very cheap, affordable solution for your needs. DIY refractory firebrick... Also BB has done a lot of testing of various affordable solutions. See pyrolysis section at BB website...

Thanks, Excalibur, here is a link to some of my experiments in high temperature insulation.

[jonathan]

insulation

thanks beyond biodiesel great home made insulation keep it up

[AlicaReik]

The activity of the animal beings has become acutely active everywhere on this earth. Bodies do not get time to booty a blow for a while. With the accretion use of altered gadgets of Gps Jammer, the possibilities of accepting the aboriginal of blow accept absolutely finished. The adaptable phones or the corpuscle phones are some of these accessories that accumulate the bodies consistently in blow with the alfresco world. The adaptable building are additionally accessible about everywhere these canicule and due to this the accessibility of the signal jammers for sale has become alike added quick and authentic. Today, you cannot break out of ability of these adaptable building as their signals can bolt your about anywhere. The bearings of bodies who accord to altered business professions has become actual analytical of wifi jammer as their authorities bolt them anywhere any moment.

[dedooo]

Hello all these pictures of reactors

[dedooo]

These pictures of reactors 2

[dedooo]

But I have a problem waste and solid waste by 30% of the raw materials I faced great difficulty in taking them out of the reactor because it is attached to, at the tips?

[Beyond Biodiesel]

Welcome, dedooo. It looks like you have a proper flange on the top of your retort, and your gas burner setup looks well done as well. What did you do for insulation? It looks like mud, or something liquide, and poured in then set?

Cleaning out the retort can be a real problem, so a flange top and bottom can help, so that you can scrape from the top, and debris can fall through the bottom flange.

Another option for cleaning out the retort after your cracking run is, if you are absolutely sure that your retort has fully cracked and extracted all of the liquid hydrocarbons, so that there is only coking remaining, then you can introduce air into your retort, by cracking open a valve and carefully watching the retort temperature. The temperature should rise to 1200F (650c) as the carbon burns. You can keep adding air, while carefully watching the temperature, and keeping it at 1200F (650c).

NOTE:
At this time you will want to valve off your retort to your fractionation column, and vent it directly out.

At this point you can turn off the heat, because the coke will keep the retort hot until all of the coke is burned off. When all of the coke is burned, then the temperature of your retort will start to drop significantly. When all of the coke is burned you will just have ash to remove. That ash can be used as catalyst for the next run.

[Excalibur]

Dedooo, looks like your reactor waste is not fully cracked. When a run is totally completed the residue is like dry carbon char, something like biscuit in texture. I suggest to do multiple runs before clearing out the reactor, but on the last run be sure and bake well so the contents is absolutely dry.

In theory, as fuel is extracted the remaining liquid hydrocarbon will become heavier and heavier. Therefore the boiling point will trend slightly higher and higher.

I've only cleared my Orion reactor just once and I struggled because it is 1.5m deep. All the carbon was on the reactor floor. So the next time I do this task, my plan is to pound the carbon biscuit char to dust and suck it out with a vacuum cleaner.

Pictures of carbon cleanout of retort from DIYdiesel

Hope this helps.

[dedooo]

help me

Please help me, today filled reactor Plastic entirely, because the pieces were not small, and I have added one liter of engine oil waste, and set on fire slowly, after two hours out liters of oil, then start the diesel out a little bit and all of a sudden, came the plastic melted quickly in a scene scary and intense , where a bug, please help me thank you for all

[Beyond Biodiesel]

Dedooo, it sounds like you need to work on your reflux.

[Excalibur]

[Excalibur]

Please help me, today filled reactor Plastic entirely, because the pieces were not small, and I have added one liter of engine oil waste, and set on fire slowly, after two hours out liters of oil, then start the diesel out a little bit and all of a sudden, came the plastic melted quickly in a scene scary and intense , where a bug, please help me thank you for all

Dedoo. I'm struggling to understand, sorry.

I'm wondering if you have over-filled the reactor? Have you experienced boil-over? Are you trying to crack plastic without a thermocouple? Do you have a reflux chamber fitted above the reactor?

The pipe on your reactor top flange looks too small?? If that plugs with plastic, you have potential bomb!

Maximum 3/4 full for the reactor for safety with plastic feedstock.