Lockridge Device - Peter Lindemann

[Matthew Jones]

@Peter,How much voltage is needed to go through the motor?

Matt

[mbrownn]

Peter or Matt

@n84dafun
I looked at Matts blown up coil pictures and it looks like one coil end is connected to a commutator and the other end of the coil is connected to the commutator right next to it. Which actually is baffling to me, maybe I'm wrong.

My feelings are the bigger the motor the better as far as having enough room to get 4 brushes mounted along with using decent size wire. But as you get bigger there are going to be more poles inside, they only make curved magnets so big. The motor you pictured Peter most likely has 6,8 or even 10 poles. Has anyone seen a 4" diameter or lager motor with only 2 magnets in it? Most of the motors I've seen inside of are 2 pole but they were automotive blower motors and are pretty small.

I hope your going to join me in this build Matt and anyone else who has or gets the same motor. If the 2 norths dont join into 1 big one we can always just fire the coil over just 1 of the magnets or just remove one of each poled magnets.

I'd like to here your opinions Peter and Matt.

Mark

[Matthew Jones]

Mark
Your gonna need to wind the motor different than you described above.

If you start on the top pole. Solder a connection to the commutator then wind clockwise, for a number of turns. When you get to the end of the top one go to exact opposite point on the rotor. Start on the commutator side but wind the coils counter clock wise.

The top will make a north field the bottom will make a south. And when the rotor flips over 180 out it will do just the opposite. Your bottom coil which is now on top will produce a North and vice versa

If you cannot see what I am saying draw it on paper then flip the paper over. Imagine which section of commutator is hook to which pole of the battery.

Cheers
Matt

[Turion]

Peter,
The rotor and commutator on that motor both have 16 sections, so nice even number. And those brushes are BIG. I ordered a replacement set and the caps that hold them. When they come in I will start my modifications. I have been studying the windings. Want to get it all worked out in my mind how to take it apart, then put it down on paper, check it, and then begin tearing it apart. Only want to do this once, and don't want to rewind if I don't have to. That's just a pain.

[Peter Lindemann]

16 Slots is IDEAL

Peter,
The rotor and commutator on that motor both have 16 sections, so nice even number. And those brushes are BIG. I ordered a replacement set and the caps that hold them. When they come in I will start my modifications. I have been studying the windings. Want to get it all worked out in my mind how to take it apart, then put it down on paper, check it, and then begin tearing it apart. Only want to do this once, and don't want to rewind if I don't have to. That's just a pain.

Turion,

Very good. 16 slots allows you to double up on the power of the motor by putting TWO WINDINGS on the rotor. The first winding will go around the rotor from slot #1 to slot #9, and the second winding will go around the rotor from slot #5 to slot #13. This will allow the motor to pulse 4 times per revolution, with 4 recovery pulses per revolution. The big issue for your case structure is how to mount the second set of brushes. Since it is already designed for 12 volt operation, you should be able to rewind with the same diameter wire.

Matt,

The idea is to run any of these motors with a voltage that is at least 3 times higher than its rating, so that at one half of the original "top" speed, the applied voltage is 6 times higher than the reverse generated Back EMF.

Peter

[Mark]

Mark
Your gonna need to wind the motor different than you described above.

If you start on the top pole. Solder a connection to the commutator then wind clockwise, for a number of turns. When you get to the end of the top one go to exact opposite point on the rotor. Start on the commutator side but wind the coils counter clock wise.

The top will make a north field the bottom will make a south. And when the rotor flips over 180 out it will do just the opposite. Your bottom coil which is now on top will produce a North and vice versa

If you cannot see what I am saying draw it on paper then flip the paper over. Imagine which section of commutator is hook to which pole of the battery.

Cheers
Matt

Actually Matt I think you worded it incorrectly. If I start on the top pole. Solder a connection to the commutator then wind clockwise for a number of turns. When you get to the end of the top and cross over the rotor shaft and flip the rotor over and go to the exact opposite point on the rotor. Then starting near the shaft I need to wind counter clockwise until I get up to the commutator and solder the end to it. If you hold the rotor in one position and dont flip it all the winds continue in a clockwise direction. Its basically one big coil and we're shoving the rotor shaft right threw the middle of it.

Take a bedini coil north is top, bottom is south. Flip it over and now south is top and bottom is north but the battery polarity is also switched so we're back to north on top and south on bottom. Please tell me I'm right here before I just throw in the towel.

Mark

[Peter Lindemann]

Good Possibility

Here's an even cheaper motor that appears to be a 2 pole (only has 2 bolts) but doesn't give a lot on info on:
12 VDC MOTOR | AllElectronics.com

Mark,

I was looking at this motor last night. It may work IF it has an even number of slots in the rotor and commutator. The only thing to do is buy one and open it up. If it has an even number of slots, then buy another one. That way you will have two sets of brushes to work with and two rotors, as well.

It would also identify an inexpensive motor for others to work with.

Good find (hopefully).

Peter

[Mark]

Peter

I may run the motor with the winding right in the middle if possible but I think there may be a clearence issue with where the commutator is and If I remove 2 of the magnets I dont know how much power it will make. I'll try it the way I wrote first and see what happens before I remove any magnets.

[kcarring]

hey guys.. I just bought that exact motor LOL no kidding, it's got to be.. it's identical. I bought it at princess auto in canada (surplus).

If you want, I'll take it apart and examine it or take pictures or whatever u wish. I'll back read this thread a bit so I understand what the interest was, but.. the plan was to take it apart anyway... just so you know. After having built my first SSG, I picked it up in the store and thought hmm... $10... why not... First thing I noticed, was, given that it was sitting there not wired, the shaft was relatively easy to turn, and the deck was very flat, and the motor shaft has a threaded end. I also bought it because the end cap has two nutted (looks to be 5/16") bolts that hold it together and it -appeared- to easily come apart.

*added:
There are ten slots in the commutator.
There are ten slots in the armature assembly, 5 (pairs) of arms (10 points)

I made a video of it, it's uploading right now.

Kyle

[Peter Lindemann]

Interesting....

Matt, thanks for the pics. I added some comments to your pics for a possible way to modify the motor for self-running. I also bought the motor from Allelectronics, which is little different from yours. Hopefully, it has the same number of poles inside.

-Brian

ScooterMotorSelfRunner2 | Flickr - Photo Sharing!

Brian,

Sorry I didn't comment on this earlier. If the stator magnets are really N-S-N-S, and not N-N-S-S as Matt said, then this really could be an excellent motor to work with. The one drawback is that it is designed to operate at 24 volts. The fact that it has 16 slots would let you wire it in a corresponding manner to Turion's motor, as I suggested in Post #230, above. I'm not sure it would work very well simply by snipping the connections as you have proposed in the linked image. One issue with this is that you are not going to have much "cool off time" for these windings if you run them at higher voltages, as I am recommending, to get ahead of the Back EMF. The other issue is that all of your turns produce a circular connection around the rotor, so it can partially discharge within itself, instead of discharging out the recovery brushes.

There are a lot of issues to balance off in these things to give you a motor with good torque, at good speed, with good recovery, that won't MELT!

Peter

[Turion]

Mark,
According to the PDF spec sheet on that motor, it has 10 slots. So it has an even number.

[Mark]

Mark,
According to the PDF spec sheet on that motor, it has 10 slots. So it has an even number.

Are you talking about the motor in post #224 or the bigger 24 volt motor?

[kcarring]

12 volt dc motor - surplus item

This is the 12 volt motor above disassembled, if it helps.

YouTube - 12volt DC motor - Bedini Mod?

10 slots

[Turion]

The 12 volt motor

[Turion]

Here is my motor all ready to be wound. Only I have never done this, so not really sure how to proceed. Here is a YouTube video of what I believe to be correct. Except on the video I say from slot One to slot Thirteen, and I really meant from slot one to slot NINE.
YouTube - Winding Lockridge Motor