Joulethief SEC exciter and variants

[Xenomorph]

And of course i will try to trigger a powerfull mosfet with a small 2N2222a or other transistor.

As the frequency seems to stay around 600 khz perhaps somebody could propose a cct.

[Farrah Day]

Farrah

The circuit i use is the Slayer 007 cct. The capacitor is not absolutely necessary but it reduces the current when tuned correctly. Slayer 007 recommend a variable capacitor to fine tune L2 with L1. As i have no variable capacitor i try different capacity . But this is not the best way to get the best result. So i would recommend you a variable cap .Relative question where can i find a big variable capacitor (from 5 to 600 pf) in europe ?

Ah, a variable cap - I thought something should be variable.

But I'm puzzled Woopy, by you saying that the capacitor is not absolutely necessary - perhaps someone can help me here. I thought I'd figured out how the cct worked, but it doesn't hold up without that capacitor. How can this cct possibly resonate without the capacitor??

Farrah

[woopy]

Thanks Xenomorph

i will go to sleep now and probably the night will add some new ideas to go ahead.

If any suggestion to wound a 1 meter 10 cm diameter (or more) coil perhaps with 0.4 or 0.5 mm copper ??

And of course i will try to trigger a powerfull mosfet with a small 2N2222a or other transistor.

As the frequency seems to stay around 600 khz perhaps somebody could propose a cct.

good night

Laurent

[Xenomorph]

waooow Xenomorph

very nice big coil in the center of your pix.

I will wound something like this as soon as possible.

If i see right you use a PVC pipe which diameter, and what copper wire.?

Have you measure the inductance and resistance?

And i can see in the background the Slayer 007 cct , but in the front there is another circuit with it seems to be Mosfet. So my question do you use a mosfet cct to drive the big coil ?

Thanks for sharing, i would be glad to replicate your big coil and cct.

good luck

Laurent

[woopy]

waooow Xenomorph

very nice big coil in the center of your pix.

I will wound something like this as soon as possible.

If i see right you use a PVC pipe which diameter, and what copper wire.?

Have you measure the inductance and resistance?

And i can see in the background the Slayer 007 cct , but in the front there is another circuit with it seems to be Mosfet. So my question do you use a mosfet cct to drive the big coil ?

Thanks for sharing, i would be glad to replicate your big coil and cct.

good luck

Laurent

[Xenomorph]

Uploaded with ImageShack.us

[woopy]

Hi Totoalas

it seems that you have a good circuit , but could you please send a shematic how you connect the MPSA06 to the parallel 2N2222

thank's

Farrah

The circuit i use is the Slayer 007 cct. The capacitor is not absolutely necessary but it reduces the current when tuned correctly. Slayer 007 recommend a variable capacitor to fine tune L2 with L1. As i have no variable capacitor i try different capacity . But this is not the best way to get the best result. So i would recommend you a variable cap .Relative question where can i find a big variable capacitor (from 5 to 600 pf) in europe ?

At all
yesterday afternoon i spent all the time to test the electroliser with the
outer glass-coil grounded in my house plug, than my wife came back home and ask me what i did , because all the house smelled ionised air .Not only my lab , So is it possible that by grounding the electroliser , all the house electric system is also ionised ?

good luck

Laurent

[Farrah Day]

Sorry to keep butting in guys, but because of recent observations made by Woopy, I'm going to attempt today to replicate his experiment first.

Can I just confirm the operation of the cct.

Is it simply that on power up, the capacitor is charged through the resistor, (the resistor determining the rate of charge) and once charged enough - which is very quickly - the voltage on the base of the transistor is then enough to switch it on allowing current to flow through the collector to the coil. However as soon as this happens, the capacitor starts to discharge, thereby turning off the transistor base voltage and hence the current through the collector. So the cycle repeats, Would that be a fairly accurate description of how the cct is resonating?

Sorry if I'm covering old ground... I'm a newbie at this! I'll try not to become annoying

Incidentally, I've just taken a failed FL bulb apart for the little toroid, and was quite amazed by the amount of components therein.

1 toroid
2 transistors
5 non-electrolytic caps
1 large and useful 1.5mF 400V electrolytic
6 diodes
6 resistors
1 3mH inductor
and a small signal transformer.

Blimey you guys could save these manufacturers a fortune on components alone!

Farrah

[totoalas]

Sec Hho

Dear All
please check in the S cell HHO and HHO @5 Volts . Can add two s cell shaped 316 stainless mesh screen to the ends of Avrenko diode plus lye to increase production of hydrogen ..... wihtout heating up the solution

Ive ran out of transistors as well as the store so endurance test is on my list for the week end for the SEC lighting @12 volts
2 paralllel 2n2222 plus one MPSA06 C to B and base to E of the prallel circuit
Current draw without and with MPSA06 128 and 56 mA ,,,,,,,,that solve my problem of overheating
Had been running for 8 hours now and the circuit still the same warm LOL
the circuit affects my wireless mouse in my deskstop

totoalas

[Farrah Day]

What about a 1 meter high and 20 cm diameter L1.

That should do it, lol.

Seriously though, I'll try to reproduce your experiment in the next few days so I can get a feel first hand of what's happening, because I'm already having second thoughts on my explanation in the previous post. I just feel I'm overlooking something.

All the best
Farrah

[woopy]

Hi Farrah
i just repeated the experiment to be sure, and i can confirm that when i move the outer coil from water level to the bottom of the glas , and further more when i completely remove the coil away from the glass, the electrolisis seems to stay at the same level. No dramatic change in the bubles quantity or form . Only the current goes up ?
But of course we need to make a much bigger experience to be able to measure that fact precisely. That's why we need a cct which can excite a much bigger Slayer exciter and produce more power electrolisis.
Any idea ?
What about a 1 meter high and 20 cm diameter L1. what copper wire diameter for the winding and what would be the cct ?

good night

Laurent

[Farrah Day]

Hi all
Salted water get yellow and smell not so good.

That will be the chlorine at the anode, which at least goes to show that it is indeed proper electrolysis that is occuring.

Did the dramatic reduction in current consumption come at the expense of a dramatic reduction in gas evolution? I would expect this to be the case.

I would suggest that this is occuring: You are causing the water to ionise as in your first experiment, the diodes are acting as a charge exchange bridge as before and gas evolves from each leg. However, by putting an earthed wire around the container, you now effectively have added another ground source to attract the H3O+ away from the wire cathode. Hence, as you have pulled some of the charges away, less current will flow through your diode bridge. At least that's my take on it.

Try using stainless steel instead of carbon rods.

This is great stuff, Woopy.

Farrah

[Farrah Day]

[woopy]

Hi all
Thanks to all of you for the important info and very intersting videos.

Just a little report of today's work.

I tried different water. plain tap water than salted water than baking soda water and pure distilled water.
the best result is plain tap water. with the baking soda both electrode are producing gas ? With distilled water it seems to need far more current for less electrolisis. Salted water get yellow and smell not so good.

Than i tried the MPSA 06 which work well and also the 2N3904 which is very good too.

The frequency around the glass is between 550 up to 670 khz (measured with the green loop on the probe of my scope)

Than something very INTERESTING i made a coil of some turns (0.8 copper insulated see pix) around the glas , one end of the coil is connected to a long wire and than to the house ground, the other end is free.This have a dramatic improvement on the current consumption.
For instance if the voltage is 9 volt and the current with the coil at the upper water level,is at 10 ma , if i simply let the coil fall at the bottom of the glass, the current goes to near 60 ma and if i put the coil away from the glass , the current goes to 120 ma ?? any explanation ?

Than i got problem with the carbon electrode. Some time ,not always , the non producing rod get black and than the whole electrolisis strongly diminish ?

OK that all for today Ho! i forget to mention that this experience is a real transistor frying machine

Good luck at all

Laurent

[Xenomorph]

Good morning everyone,
Does this is a Slayer's exciter ??
It looks same, but power is huge

http://www.hvlabs.hu/zpe/Gruz/overunity.com/fun with electrostatic X TROS-TT (320 x 240).flv

Comes from here: Index of /zpe/Gruz