Barbosa and Leal Devices - Info and Replication Details

[masen]

Advice

Thanks for all your valuable advice, I will post a picture in a couple of hours.

[masen]

Energy from the ground -Cont'd

I believe I made all the changes you suggested in your last two posts, Clarence, plastic box,etc. The rods are all connected with one return line, I believe the same as your diagram,[ black wire bottom left], the other four are on a separate line.[white wire on bottom left] I hope that it is right. Bye for now.


free image hosting

[clarence]

Trial run

I believe I made all the changes you suggested in your last two posts, Clarence, plastic box,etc. The rods are all connected with one return line, I believe the same as your diagram,[ black wire bottom left], the other four are on a separate line.[white wire on bottom left] I hope that it is right. Bye for now.


free image hosting

Hello masen,

Everything looks good to me.
I would power the charger by a mains receptacle for the first run
in order to keep any load off of the captor output so that you may get an exact voltage reading on the captor output to see what rms voltage is available through the ground rod return system.
I would have a DVMM set up ready to make a quick measurement on your two receptacle gang box.
Also I would have a clamp meter (if you have one) clamped on the captor
secondary top black wire ready to take an AC amperage measure.
The AC amp reading should be some where around 1.4 amps.

as a secondary method to be cautious on the trial run place your left thumb and forefinger on the top black captor secondary wire before you flip the invertor on. if you feel any immediate heat in the wire then immediately
turn the invertor off.

If there is no heat, then proceed with your measures as mentioned.
the out come of the whole event will strictly depend on the GROUND ROD RETURN SYSTEM as this is what the whole unit is about - self powered energy FROM THE GROUND.

Hope all of this helps you to achieve the good results that you
are looking for.

Best, and Respects,

Clarence

[clarence]

Trial run

I believe I made all the changes you suggested in your last two posts, Clarence, plastic box,etc. The rods are all connected with one return line, I believe the same as your diagram,[ black wire bottom left], the other four are on a separate line.[white wire on bottom left] I hope that it is right. Bye for now.


free image hosting

Hello masen,

how did your trial run go?
just curious is all.


Also I would never let yourself be placed in a hurry to
answer ANYONE including me. ALL good things take time and effort
so be sure to serve yourself FIRST.
my best wishes are always with YOU.


best wishes, and Respects,

Clarence

[BroMikey]

I believe I made all the changes you suggested in your last two posts, Clarence, plastic box,etc. The rods are all connected with one return line, I believe the same as your diagram,[ black wire bottom left], the other four are on a separate line.[white wire on bottom left] I hope that it is right. Bye for now.


free image hosting

When you get back from the weekend remember we are all on the
edge of our seats. Let us know if it is a failure or success.

Your setup is very nice.

Mikey

[wantomake]

Masen,
Yes, really curious to know how your setup works. I've got a start on this setup but not able to get the Toroids until I know more.

wantomake

[Minsky]

earth energy

Hello,
There is another person who has independently developed a system around earth currents. Hes using a regular transformer and a surge suppressor to attract the energy from the ambient which would make this a good test for the earth return circuit before venturing to the Barbosa replication.

https://www.youtube.com/watch?v=rt1Xpx1jSBc

[wantomake]

link???

Hello,
There is another person who has independently developed a system around earth currents. Hes using a regular transformer and a surge suppressor to attract the energy from the ambient which would make this a good test for the earth return circuit before venturing to the Barbosa replication.

https://www.youtube.com/watch?v=rt1Xpx1jSBc

Minsky,
Your link doesn't work. Anyone able to use this link?

wantomake

[cheors]

https://www.youtube.com/watch?v=rt1Xpx1jSBc

[tachyoncatcher]

Minsky,
Your link doesn't work. Anyone able to use this link?

wantomake

Yes, Copy and paste to your browser address bar or use this:
https://www.youtube.com/watch?v=rt1Xpx1jSBc
It's in Russian, I think.

Randy

[wantomake]

language

Thanks Tach,
But my russian is a little rus-ty.

wantomake

[CANGAS]

Clarence, I discovered your good work over on that other thread, and followed your trail to here when the lunatics overcame the asylum over there.

I just want to say, thanks, thanks, thanks for your good work and your report of it. for many years I have been optimistically looking for free energy in the field of mechanical systems, also including the use of magnets or electrostatic components. My work has NOT been completely fruitless, though it is not yet exactly the right circumstances for me to make any announcements.

Your work is immensely reassuring. What would really get the party started is if it could be scaled way down so that even a poor boy like me could buy $1.98 worth of parts and prove the principle for himself on a small scale before spending big money (for a poor boy) to build the real thing.

My practical electrical and electronic expertise is very small. I am urgently hoping that somebody who knows their volt from their amp will design a LITTLE demonstration device that might only make 10 watts, or 1, but will do it reliably and undeniably.


Best regards and God bless you!
CANGAS

[clarence]

Clarence, I discovered your good work over on that other thread, and followed your trail to here when the lunatics overcame the asylum over there.

I just want to say, thanks, thanks, thanks for your good work and your report of it. for many years I have been optimistically looking for free energy in the field of mechanical systems, also including the use of magnets or electrostatic components. My work has NOT been completely fruitless, though it is not yet exactly the right circumstances for me to make any announcements.

Your work is immensely reassuring. What would really get the party started is if it could be scaled way down so that even a poor boy like me could buy $1.98 worth of parts and prove the principle for himself on a small scale before spending big money (for a poor boy) to build the real thing.

My practical electrical and electronic expertise is very small. I am urgently hoping that somebody who knows their volt from their amp will design a LITTLE demonstration device that might only make 10 watts, or 1, but will do it reliably and undeniably.


Best regards and God bless you!
CANGAS

Hello GANGAS,

I admire your serious attitude for certain.
Your definition of the lunatics overcoming the asylum was on point.

the only way to achieve a tiny version would be by using mains power in order to get a 1.98 unit and even that would cost a little more than 1.98
but I get your point!
the other danger lurking in the shadows would be the mile-a-minute el-chepo
do nothing whiney mouths jumping in to splatter the thread with their usual
"bear in the woods" donation.

this week I am finishing my cart unit re-build and then I will do what you speak of just out of curiosity for my self. I already know how to do it it's just a matter of taking the time to do it.
as always , time will tell all.

Thanks for your interest,
Best Wishes, and Respects

Clarence

[Bob Smith]

Hibridor's B&L Analysis

Hi Guys
No wish to upset or discredit anyone taking a different approach. Just thought I'd share this analysis by YT user Hibridor (below).
Bob

Analysis of Electron Capture Apparatus Barbosa/Leal
by Wilson Roa

https://www.youtube.com/watch?v=BNPDQ2mu_qg

[level]

Hello GANGAS,
the only way to achieve a tiny version would be by using mains power in order to get a 1.98 unit and even that would cost a little more than 1.98
but I get your point!

I have already explained several times and also fully demonstrated why (for many countries anyway) you can't use the mains to power a Barobosa and Leal device arangement. The power going to the load is coming directly from the mains in that arrangement due to a ground loop. This should give people cause to think why Barbosa and Leal were doing demonstrations powering from the mains then. Are they just common scam artists or did they just have no idea what they were doing?

Any testing other than with using only a battery and inverter (with no mains connection at all) is completely meaningless. Clarence please stop trying to deceive people with this sort of nonsense about using the mains. You have demonstrated absolutely nothing so far, and you spoke of tests done using the mains, which shows you either have no understanding at all what you are doing, or you are deliberately trying to deceive people for whatever reason. Do you not care at all that people could spend lots of money trying to replicate your setup, when your own setup itself does not work at all? It would be different if you can actually demonstrate a self running setup that runs for many days on a battery and inverter without the battery running down, but of course you haven't been able to do anything of the sort, at least not so far anyway, and instead you just insult people who point out the facts of the matter. Sorry to be blunt, but it really appears that you want to continue to try to deceive people here and give advice on how to build devices without you having demonstrated a single basic thing so far in regards to how your setup can really perform.