Ufopolitics Basic Asymmetric Example Questions

[parkham]

Hi. Please forgive my ignorance. I have some questions regarding the Youtube video by Ufopolitics called "ASYMMETRY TO ENLIGHTENMENT".

I would like some clarification as to what some of the components are at timestamp 11:00 and 12:00





What are 1A and 1B?

What are 2A and 2B? Resistors?





3A and 3B : Just terminals or some sort of diode?

What is 4A?

5A and 5B: Are they the "brushes" of this motor?

Thanks again and apologies if I seem like less than a neophyte.

[Ufopolitics]

Welcome

Hi. Please forgive my ignorance. I have some questions regarding the Youtube video by Ufopolitics called "ASYMMETRY TO ENLIGHTENMENT".

I would like some clarification as to what some of the components are at timestamp 11:00 and 12:00

Hello Parkham,

You could have posted your questions in MAEM Thread...but it is Ok...let me try to clear this for you.

What are 1A and 1B?

1A and 1B are Battery Symbols (Storage of Energy) contained within the coils.

Theoretically, this concept is based on previous explanation from a single coil loop in the Symmetrical model that is shown before on video...the image is below:

[IMG][/IMG]

What are 2A and 2B? Resistors?

Yes, they are resistors symbols, representing the resistance for each respective coil (Gold and Green Wire loops).

3A and 3B : Just terminals or some sort of diode?

3A & 3B are "Arrows Heads in 3D" representing the current flow

What is 4A?

4A= Resistors in 3D, exactly the same as 2A & 2B above, but in 3D

5A and 5B: Are they the "brushes" of this motor?

5A & 5B are the specific Commutator Elements making contact with the brushes (rectangular dark grey cubes between 3A & 5A, and between 3B & 5B ) and they are color coded the same as each coil loop they are connected to.

3A(+) & 3B(-) LEFT on IMG are the Motor Input, on the above frame the Green Coil loop is receiving energy, therefore, acting as Motor, creating a rotation, while 3B Top Negative (-) and 3A Bottom(+) are the Output taken from Gold Coil loop through their respective commutator elements-brushes.

The IMG below shows on video the way Energy Flows...

[IMG][/IMG]

Red Arrow Flow is the Input that creates Motor Action, while the Green Arrow represents the Output Flow.

Thanks again and apologies if I seem like less than a neophyte.

No problem, hope this clear some of your doubts...and thanks for your interest on this...maybe I will see you soon, putting together in reality one of this Machines.


Regards


Ufopolitics

[parkham]

Any suggestions on an easy way to build the elements and brushes for this two wire design? I have a good idea on how to start now, though. Do you have a replication of this already that I may refer to? I see lots of motors but havent seen this.

Thanks,

[parkham]

Bump? Do you have an original design I may look at?

Any suggestions on an easy way to build the elements and brushes for this two wire design? I have a good idea on how to start now, though. Do you have a replication of this already that I may refer to? I see lots of motors but havent seen this.

Thanks,

[Bob Smith]

I hope I'm not speaking out of turn here, but thought I'd help point the way to what UFO has posted.

Parkham, the two wire winding is really just for illustration purposes on how coils interact with magnets as they pass by (Lenz' Law) and how windings in conventional DC motors waste a lot of electrical charge by their constant polarity reversal. A typical 5 pole motor is going to have 5 sets of windings; a 3 pole will have 3. I'd suggest you go to this post and check out the diagram:

http://www.energeticforum.com/renewable-energy/11885-my-asymmetric-electrodynamic-machines-2.html#post201465

A little further on, you'll see Woopy's link to his video showing how he replicated the 5 pole UFO asymmetric machine. If you continue on in the thread, you'll find directions on where to find and how to modify these DC motors.

I hope this helps...
Bob

[Ufopolitics]

Many Thanks Bob!!

I hope I'm not speaking out of turn here, but thought I'd help point the way to what UFO has posted.

Parkham, the two wire winding is really just for illustration purposes on how coils interact with magnets as they pass by (Lenz' Law) and how windings in conventional DC motors waste a lot of electrical charge by their constant polarity reversal. A typical 5 pole motor is going to have 5 sets of windings; a 3 pole will have 3. I'd suggest you go to this post and check out the diagram:

http://www.energeticforum.com/renewable-energy/11885-my-asymmetric-electrodynamic-machines-2.html#post201465

A little further on, you'll see Woopy's link to his video showing how he replicated the 5 pole UFO asymmetric machine. If you continue on in the thread, you'll find directions on where to find and how to modify these DC motors.

I hope this helps...
Bob

Hello Bob!!

Many thanks friend for getting this cleared up...the WHOLE Post you wrote above is PERFECT!

I do not need to write anything else...

Many thanks Dear Friend!


Kind Regards


@ Parkham:

Please, if you are gonna start building Models go to MAEM Thread, and start reading...everything is there...and the smallest Motor -Commercially- Built (based on Number of Poles) is the THREE POLES...and I highly suggest you start by making this type before moving to the FIVE POLES.


Regards


Ufopolitics

[parkham]

OK, I guess you answered the question! I'm looking for the simplest proof of concept based on your YouTube video - the three pole motor. I'll check it out.