Announcement

Collapse
No announcement yet.

Eric Dollard

Collapse
This is a sticky topic.
X
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Sputins
    replied
    2018 update:

    Glom obtained for a new RF generator and complete rig.

    An old mass spec has been gutted leaving the frame, RF housing and compartments which have been cleaned or repainted as appropriate.

    My (old) parallel 807 tube RF generator has been mounted onto the MS frame which will be used to power the next (high power) RF generator stage.
    This high power RF gen consists of a +2KVA transformer that produces 4kV at 750mA. Once rectified and filtered by large capacitors and choke gives a plate DC voltage of almost 6kV. The RF tube supplied is a 3CX1500D3 with the appropriate socket, housing, chimney, and large blower fan. – This has been restored and is operational.

    The old MS plasma circuit used a Colpitts Oscillator with this tube, but I am attempting to change the circuit to a “grounded grid” system, driven by the dual 807’s which should produce the 75-100 watts needed to drive the grounded grid stage. (The 807 stage feeds through the grounded grid to provide additional RF power).

    The top of the MS frame will hold a top deck which will have the Tesla Coils mounted on the top in various configurations, with the RF power fed in from below, (either low or high power). The whole contraption is on wheels so it can be moved about, transported or just moved out of the way.

    “Grounded grid” as the input RF fed into the cathode, generally via the filament heater supply which is kept isolated from “RF ground” via a large bifilar wound RF choke, but the DC circuit is maintained via the centre tap of the Filament transformer (6.3v @ 25amps). – This part is also completed.

    The next stage is to complete the input circuit, which requires a pi, L or impedance matching network with (Q4) to provide an impedance match between the 807’s drive and the input of the grounded grid. Then the output circuit from the tube to complete but has already been partly assembled.

    Photos later.
    Sputins & his chickens.

    Leave a comment:


  • Vinyasi
    replied
    Synthesis of Electricity from Caps and Coils

    In homage to Eric's statement during one of his earlier lectures, either History and Theory of Electricity or Origin of Energy Synthesis - I don't recall, in which he says that mere capacitors and coils can be used to synthesize electricity, and since I'm still endeavoring to get a theoretical handle on the LMD analog computer as an amplifier by simulating - rather than building - the following simulations are provided, below, using two daisy-chained LMDs exhibiting various amounts of resistance (impedance) at their inductive loads of one Henry, each ...

    Simulated in Java -- load the text from the attachment posted below, or use this alternate Java Simulator

    Simulated in JavaScript

    How to Operate a Parametric LMD Satisfying an AC Oriented, EV Motor -- a Vimeo video...

    I like this simulation since it uses twelve capacitors in its LMD modules hinting at a parallelism with the Tesla story/myth of a 1931 Pierce-Arrow conversion into an A/C motored EV which had used twelve (radio) tubes may have, instead, been twelve vacuum tube capacitors?
    Attached Files
    Last edited by Vinyasi; 08-23-2018, 05:15 PM. Reason: Reduced impedance by adding a shunt resistor between the inductive loads. Shorting the two pairs of loads to each other also helps.

    Leave a comment:


  • Marcus Neuhof
    replied
    Emailed you yesterday. If it did not arrive, check your spam folder or send me a PM on the forum. (my forum inbox has shunk to a limit of 5 messages? I cleared it out, in any case)

    Leave a comment:


  • Aaron
    replied
    bitcoin

    Originally posted by Marcus Neuhof View Post
    Thank you for the quick reply.

    I already bought some Bitcoin for this, so I will wait for you to confirm the cryptocurrency details.

    I have edited the original post to reflect that the cryptocurrency payment information may not be current.

    Please send me an email info at emediapress dot com and I'll give payment info for bitcoin. Thank you.

    Leave a comment:


  • Marcus Neuhof
    replied
    Thank you for the quick reply.

    I already bought some Bitcoin for this, so I will wait for you to confirm the cryptocurrency details.

    I have edited the original post to reflect that the cryptocurrency payment information may not be current.

    Leave a comment:


  • Aaron
    replied
    paypal

    Originally posted by Marcus Neuhof View Post
    Thanks!

    For some reason Clickbank is not accepting my payment / not letting me check out. Perhaps it is because I am abroad, or perhaps it is "nem".

    I see in the Cryptocurrency Marketplace here that you accept payments via Bitcoin for all eMediaPress products, and Bitcoin payments -- in addition to reducing portly central bankers to puddles of gibbering hate -- are more difficult to "interfere with".

    How can we pay via Bitcoin?

    (Incidentally, if you need a payment processor, a friend recommends https://www.coinpayments.net/ )


    EDIT: I found the page explaining how to buy eMediaPress products with Bitcoin/Litecoin/Teslacoin: A & P Electronic Media - Digital Publishing by Aaron Murakami & Peter Lindemann

    If anyone else has been having issues with Clickbank, here is another way.

    You can pay direct to paypal if needed - paypal email is: shop at emediapress dot com - can send total listed on the website and follow up with a note about what you are making payment for. You'll receive the download links by email then.

    I have to verify the info for the crypto.

    Leave a comment:


  • Marcus Neuhof
    replied
    Thanks!

    For some reason Clickbank is not accepting my payment / not letting me check out. Perhaps it is because I am abroad, or perhaps it is "nem".

    I see in the Cryptocurrency Marketplace here that you accept payments via Bitcoin for all eMediaPress products, and Bitcoin payments -- in addition to reducing portly central bankers to puddles of gibbering hate -- are more difficult to "interfere with".

    How can we pay via Bitcoin?

    (Incidentally, if you need a payment processor, a friend recommends https://www.coinpayments.net/ )


    EDIT: I found the page explaining how to buy eMediaPress products with Bitcoin/Litecoin/Teslacoin: A & P Electronic Media - Digital Publishing by Aaron Murakami & Peter Lindemann

    If anyone else has been having issues with Clickbank, here is another way.

    EDIT: Aaron suggests this may not be in working order anymore. See below for updates.
    Last edited by Marcus Neuhof; 08-15-2018, 12:29 PM. Reason: Added link to page with cryptocurrency details

    Leave a comment:


  • Aaron
    replied
    supporting EPD Laboratories, Inc.

    Originally posted by Marcus Neuhof View Post
    Hi Aaron,
    Thanks for doing that. One question:

    There used to be an affiliate link we could use to send a (larger?) % of the book proceeds to Eric. I think it was if you ordered via ericpdollard.com ... however I am not seeing any affiliate links there.

    What's the correct link we should be using to order?

    Hi Marcus,


    You can use any of the links in the thread. In addition to the normal royalty that Eric receives, I'm putting in extra from the sales of the vids to pay off the entire building by the end of next month so Eric and EPD Laboratories, Inc. will receive benefit no matter what.

    Leave a comment:


  • Marcus Neuhof
    replied
    Hi Aaron,
    Thanks for doing that. One question:

    There used to be an affiliate link we could use to send a (larger?) % of the book proceeds to Eric. I think it was if you ordered via ericpdollard.com ... however I am not seeing any affiliate links there.

    What's the correct link we should be using to order?

    Leave a comment:


  • Aaron
    replied
    Free engineering report by eric dollard

    URGENT – FREE ENGINEERING REPORT BY ERIC DOLLARD ON WHY THE GRID HAS BECOME DEGENERATED AND WILL ACTUALLY ASSIST AN EMP ATTACK INTO CAUSING MORE DAMAGE! Ask Eric Dollard questions live about this topic.

    The letter on Eric’s recent presentation page has been changed.

    We were waiting for this report and only just now have it available. Whether you have this presentation or not, READ THIS!! If that doesn’t make you concerned about what the grid has become, then nothing will.
    Share this far and wide!

    Anyone who does have this presentation by Sunday will be invited to a LIVE CALL with Eric Dollard (by email) to ask questions and discuss this very important topic.

    History, Theory & Practice of the Electrical Utility System by Eric Dollard

    Leave a comment:


  • Aaron
    replied
    Eric Dollard's MWO for sale

    ERIC DOLLARD’S PERSONALLY ENGINEERED, HAND-BUILT PULSE MODULATOR IS FOR SALE

    IT IS A FULL SYSTEM COMPLETE WITH EVERYTHING YOU NEED TO OPERATE A LAKHOVSKY MWO – YOU CAN USE THIS PULSE MODULATOR FOR COSMIC INDUCTION GENERATOR EXPERIMENTS, ETC.
    IT WILL COME WITH THE LAKHOVSKY RING ANTENNAS – THE ONES YOU SEE IN THE PICTURE BEFORE ARE CAPACITOR RINGS FOR TESTING


    Eric Dollard's MWO For Sale - A & P Electronic Media

    Leave a comment:


  • Aaron
    replied
    History, Theory & Practice of the Electrical Utility System by Eric Dollard




    "The Grid Is Being Degraded And It Has Become An Antenna To Amplify The Damage Done By An EMP! This Is One Of The Most Disruptive Presentations Ever Delivered By Eric Dollard. Correcting These Dangerous Practices Is A Matter Of National Security."

    REVEALED: How the power companies are bypassing safety features and other built in securities at a higher cost evidencing the fact that competent power engineers appear to no longer exist - they're sabotaging the grid and don't even know it. This presentation is 5 hours long!

    History, Theory & Practice of the Electrical Utility System by Eric Dollard

    Leave a comment:


  • Marcus Neuhof
    replied
    I hope everyone enjoyed the conference. Will someone post a writeup for those of us who could not attend?

    For those of you who were watching the Thai cave rescule -- and Eric, if he is still at Aaron's and near a computer -- it is perhaps of interest that a telluric radio system was used to communicate with the team underground.

    The system is called a Heyphone and all schematics and construction plans are available on the Internet:

    HeyPhone Introduction
    https://www.xray-mag.com/content/tha...-gnarly-diving

    While the Heyphone is no longer in production, the Swiss make a digital version:
    Base Unit

    Leave a comment:


  • Aaron
    replied
    Awesome results!

    Originally posted by Macak View Post
    Some recent works with resonant transformers built for Eric's Cosmic Induction Generator.

    First series: The center field between the two conjugate wound transformer secondaries is AM modulated, exposed to a burnt out 500 watt bulb creating the Aurora plasma mist. About 150 watts excitation at 1900 kHz.

    Second series: Single transformer, AM modulated musical plasma discharge. Bach on a spark. Description below.

    Macak is back!


    [IMG][/IMG]

    [IMG][/IMG]




    [IMG][/IMG]

    [IMG][/IMG]

    Video below: Music from a plasma discharge. There is NO speaker in this video projecting the sound. The sound is being projected from the plasma arc discharge displacing the air as it pulsates to the audio frequiencies. The arc is being generated by an amplitude modulated radio frequency signal (1900KHZ) from a radio transmitter at a power level of approximently 400 watts. The device shown creating the arc is a quarter wave resonant transformer (Telsa Coil) in telluric mode with the lower terminal of the transformer's secondary connected to earth. Design form factor is by Eric Dollard N6KPH and proportioned and fabricated by Bruce Gavin KD1MW.
    Recording of video and audio was done with a Canon EOS M camera. Only the built in microphone of the camera was used to record the sound. Note the sharp pointed tips from the plasma brush discharge when the camera finally focuses. This is an organic shape that can be found in many natural conditions. Audio chain was limited to just the narrow bandwidth of the Yaesu FT990's AM passband. The bright light that appeared for a moment was a small florescent tube reacting to the high magneto dielectric field surrounding the plasma discharge.
    Macak, this is exciting! Great to see a conversation turn into this!

    Saw your email - just been swamped.

    Leave a comment:


  • Aaron
    replied
    Hi Adrian

    Originally posted by aminnovations View Post
    Hi,

    I am very happy to be attending the 2018 conference! I have wanted to attend for many years but there have always been other responsibilities calling on my time. Finally I am able to come and looking forward to meeting everyone, all the discussions, and presentations.

    I have also at last started to write-up some of my own work in a blog website. It is just the beginning, and a lot of material and experiments yet to be added, but it is work in progress, and good to finally be sharing my own work.

    For those interested the link is:
    AMInnovations | Research into the displacement and transference of electric power

    73,
    Adrian
    Hi Adrian,

    Please do introduce yourself to Eric and I at the conference. I want to show him some pictures on your website so he knows the amazing work you're doing. Would like to learn more!

    Leave a comment:

Working...
X