Anyone know where to have a flywheel made in the UK?

[Sephiroth]

Title says it all

Looking for somewhere in the UK that can make some custom flywheels for me.

Spec :
100mm diameter
approx 30mm thick
with an 8mm hole in the center for the shaft.

Material must be non magnetic, and obviously very dense (perhaps lead?).

[tjnlsn255]

That sounds like something any good machine shop could do....

Would aluminum work?

To bad it has to be nonmagnetic..... sounds a lot like a flywheel at the back of a car engine.....

Hopes and Dreams....

Tj

[Sephiroth]

Alluminium is ok, but isn't very dense (about 2.7g/cm^3)

yeah, non magnetic is a pain, but it's going to be positioned very close to my stator coils. Don't really like the idea of them being conductive either to be honest....

[john_g]

Alluminium is ok, but isn't very dense (about 2.7g/cm^3)

yeah, non magnetic is a pain, but it's going to be positioned very close to my stator coils. Don't really like the idea of them being conductive either to be honest....

Hi Sephiroth

I suspect if you want it made in lead there may be a few H&S problems with turning lead. What about casting it yourself - find a tin of the correct diameter, bed it in sand level, and pour in your molten lead. Or you could use a lead shot/ resin mix, which may be easier.

Regards

John

[Sephiroth]

Hi Sephiroth

I suspect if you want it made in lead there may be a few H&S problems with turning lead. What about casting it yourself - find a tin of the correct diameter, bed it in sand level, and pour in your molten lead. Or you could use a lead shot/ resin mix, which may be easier.

Regards

John

Yeah, I was thinking of doing that but I need at least two identical pieces, and am willing to pay for precision

[tjnlsn255]

Does it have to be metal?

What about making them out of fiberglass or resin?

Hope you are having fun on your adventure.....

How is the M3 coming along?

Be happy....

Tj

[Sephiroth]

Does it have to be metal?

What about making them out of fiberglass or resin?

Hope you are having fun on your adventure.....

How is the M3 coming along?

Be happy....

Tj

I can have them made from acrylic, but it's far too light... for such a small flywheel, I need a very dense material...

the MG3 is in the works, but I have something I need to finish first Should have something to show in the next month...

[juju]

flyweel

hello my friend,

you can get a rotor from an old computer hard drive, with almost that size you mention... the disk is made from some kind of metal but non magnetic material... the rotor also includes very good bearing prepared for high rpms.

thats what i use in my rotors!

its just an idea... why to make one, if you can get it from some old component, and easy to find!

i have lots of damaged hard drives here, so if you really need i can send you one...

or you mean something else? im not shore if we are talking about the same, dont really know what you mean with flywheel...




hugs

[Slovenia]

Where to find flywheel in UK?

Hi Sephiroth,

Check with Patrick Kelly, the author of Practical Guide to Free Energy Devices. He knows where to find everything. You can find contact information for him at the following site:
Free-Energy Devices, zero-point energy, and water as fuel

Best Regards,
Slovenia

[Sephiroth]

hello my friend,

you can get a rotor from an old computer hard drive, with almost that size you mention... the disk is made from some kind of metal but non magnetic material... the rotor also includes very good bearing prepared for high rpms.

thats what i use in my rotors!

its just an idea... why to make one, if you can get it from some old component, and easy to find!

i have lots of damaged hard drives here, so if you really need i can send you one...

or you mean something else? im not shore if we are talking about the same, dont really know what you mean with flywheel...




hugs

Hi Juju,

A flywheel is a heavy rotating mass used to store kinetic energy... rotors aren't a problem since I can get anything I want made from acrylic but thank you for the offer

@Slovenia - Good thinking! Looks like he's based in the UK so he could well be the best person to ask!

[wrtner]

Title says it all

Looking for somewhere in the UK that can make some custom flywheels for me.

Why not use a grinding wheel, as supplied by any builders' merchant?

[Sephiroth]

Why not use a grinding wheel, as supplied by any builders' merchant?

lol.... no where near heavy enough! Thanks though!

[Sephiroth]

By the way guys, I'm not looking for an alternative!

[Stealth]

flywheel

You can make a flywheel out of any material, just drill the end of the wheel and add any amount of lead weights you want to make it as heavy as you need. It will have to be drilled and balanced precisely though, if you are to run it at a very high RPM. Nylon will work good for this, and is easy to drill and insert weights into the outer rim.Good Luck with your project. Stealth

[ray0energy]

Nilon or Teflon best flywheel

Title says it all

Looking for somewhere in the UK that can make some custom flywheels for me.

Spec :
100mm diameter
approx 30mm thick
with an 8mm hole in the center for the shaft.

Material must be non magnetic, and obviously very dense (perhaps lead?).

I find a place here in Spain that cell nilon and teflon in redy made disks or plates and good price to that were u look for will be like 30 buks and then u
only need a center hole. Look for a plastic suplyer in yellow page if u can't find one. I have one here for u;-) if u pay sending form Barcelona it's 100mm diameter and 30mm it's nilon