Energetic Forum  
Facebook Twitter Google+ Pinterest LinkedIn Delicious Digg Reddit WordPress StumbleUpon Tumblr Translate Addthis Aaron Murakami YouTube PRE-REGISTER - 19 SEATS LEFT!!!*** 2017 ENERGY CONFERENCE ***


* NEW * BEDINI RPX BOOK & DVD SET: BEDINI RPX


Go Back   Energetic Forum > >
   

Renewable Energy Discussion on various alternative energy, renewable energy, & free energy technologies. Also any discussion about the environment, global warming, and other related topics are welcome here.

Bedini RPX Sideband Generator
Reply
 
Thread Tools
  #1  
Old 10-04-2010, 04:17 PM
Jbignes5 Jbignes5 is offline
Gold Member
 
Join Date: Mar 2009
Location: NY, USA
Posts: 1,014
Don Smith A review...

For your pleasure I am re introducing this subject.

http://www.free-energy-info.co.uk/DonSmith.html

This explains what we need to do to make systems based off of Radiance. It explains radio antenna theories that must be included in your design when you include coils or have wires involved in any way without suitable shielding.

More then halfway through this document he touches on his high wattage device that actually produced a result that all of us are looking for. We need to read this stuff and understand it to fully take advantage of the radiance we all wish to use.

I know it is a long document but please read it all before commenting on this subject. Understand that no matter if the wire is coiled that it is still an antenna and that antenna when not shielded from the environment will interact with that environment. There are a lot of good techniques and accurate information in this document to be able to take the freq., capacitance of your circuit and resistance and design a coil or transformer to be in full resonance with the circuit before even making the coil or transformer.

There is an excellent tutorial describing the device he had which was based off of the Tesla setup I have been trying to show everyone. This tutorial describes all the processes and explains the method in detail so we can produce the same thing on here.

I would like all the real experimenters on here to go along with me on this journey to rediscover what has been discovered many times in the past. We need real setups to observe and I hope that you guys follow along in this journey.
__________________
 
Reply With Quote

Download SOLAR SECRETS by Peter Lindemann
Free - Get it now: Solar Secrets

  #2  
Old 10-05-2010, 12:34 AM
gmeast gmeast is offline
Gold Member
 
Join Date: Aug 2008
Posts: 1,129
thanks for the doc

Quote:
Originally Posted by Jbignes5 View Post
For your pleasure I am re introducing this subject.

http://www.free-energy-info.co.uk/DonSmith.html.................................................. .................................................. .........and that antenna when not shielded from the environment will interact with that environment. .................................................. .................................................. .....
Hello Jbignes5,

I searched for this information by Don L. Smith ... I can't tell you for how long. Thanks for this info'

Do you have any idea how potent a statement the above is ? This is probably where many folks give up or simply can't connect the dots.

... THINGS MUST BE PROPERLY SHIELDED ... and much MORE than that ... THE RIGHT THINGS MUST BE SHIELDED IN THE RIGHT WAYS ...

Again, thanks,

Greg
__________________
 
Reply With Quote
  #3  
Old 10-05-2010, 06:40 AM
7imix 7imix is offline
Senior Member
 
Join Date: Sep 2010
Location: Planet Earth
Posts: 380
I can't thank you enough for posting this. Your post was perfectly synchronistic with what I have been thinking about the past few days. I read the whole thing today. It encapsulates perfectly what is important about Tesla's devices.

I'm ready to go on this journey with you. I want to replicate something using the knowledge here and get some measurements on it. There is not much detailed replication information in the document although the following two projects look quite promising:





I also especially like the section at the end with detailed information about coil construction, capacitor construction, and series multiple spark gap construction.

What do you think? Where can we start with this information and make a reproducible experiment?
__________________
 
Reply With Quote
  #4  
Old 10-05-2010, 12:27 PM
Jbignes5 Jbignes5 is offline
Gold Member
 
Join Date: Mar 2009
Location: NY, USA
Posts: 1,014
Quote:
Originally Posted by 7imix View Post
I can't thank you enough for posting this. Your post was perfectly synchronistic with what I have been thinking about the past few days. I read the whole thing today. It encapsulates perfectly what is important about Tesla's devices.

I'm ready to go on this journey with you. I want to replicate something using the knowledge here and get some measurements on it. There is not much detailed replication information in the document although the following two projects look quite promising:





I also especially like the section at the end with detailed information about coil construction, capacitor construction, and series multiple spark gap construction.

What do you think? Where can we start with this information and make a reproducible experiment?
Initially I wanted to have a tutorial about making coils and transformers. But the more I read the document the more it was exactly in line with what I had discovered from my Tesla research. Although what is in the document is not word for word from my own theories they are very very simular.

Well I read the whole thing.. I am gonna reread it a couple more times because every time I read it I see something new that I didn't noticed before. I am most likely gonna read the section about coils and how you need to design the coil based on very specific information like Target frequency and the rest of the circuit. I think if the coil that you have designed should have been designed and not thrown together.

I am amazed that most here throw their coils together and don't think twice about it's resonant qualities. I knew antenna theory that I was using was gonna become very important to me later on. The days of my youth were spent on CB equipment like amps and antennas and learning about reflective energy and how it affects the rig or transmitter.

So what we need to do is find a frequency of interest then design the rest of the circuit around that freq. The diagrams about the Tesla device or table top generator would be nice to start with. It has what I have been looking for. A modern approach to the system that I bet ran the Pierce arrow experiment that Tesla did. Just below the pictures you have shown is a section called "Useful circuits from Nikola Tesla"



I think once reading the first part it gives enough information to be able to figure out the secret Tesla experimentally fleshed out. I will be focusing there but there is sooo much in this document that each and everyone can specialize in a different area and maybe we can all together build a working model that produces the energy we are looking for from this information.

It looks like someone also made the connections that I did so this has re energized my focus and maybe I can get this idea out of my head. It has been nagging me for quite some time now.
__________________
 
Reply With Quote
  #5  
Old 10-05-2010, 12:42 PM
Jbignes5 Jbignes5 is offline
Gold Member
 
Join Date: Mar 2009
Location: NY, USA
Posts: 1,014
Quote:
Originally Posted by gmeast View Post
Hello Jbignes5,

I searched for this information by Don L. Smith ... I can't tell you for how long. Thanks for this info'

Do you have any idea how potent a statement the above is ? This is probably where many folks give up or simply can't connect the dots.

... THINGS MUST BE PROPERLY SHIELDED ... and much MORE than that ... THE RIGHT THINGS MUST BE SHIELDED IN THE RIGHT WAYS ...

Again, thanks,

Greg
Yeah it is funny but I didn't really look at my own words till you re posted it lol. Yes those words are very important to anything we have or will learn from this. Everything is an antenna. Even resistors can be considered antennas if you have the view that all charges are external to matter. Especially when the frequency goes above 20k (radio Frequency).

Tesla started to use static shielding in his designs after he figured out that this special energy flowed like water. The shielding acts like a container and limits the ability of the charges to escape or enter through that shielding. This allows one to have a pressure that can not escape or attain a balance with the ambient pressures. This also made his devices very easy to understand after making that connection. Tesla was well versed in making a vacuum and eventually versed himself well on making turbines. So he learned a lot about controlling the pressures he wanted to create to attain an imbalance that he could use to funnel in real power in a cyclic way. <-Non harmful, more natural.
__________________
 
Reply With Quote
  #6  
Old 10-05-2010, 03:21 PM
7imix 7imix is offline
Senior Member
 
Join Date: Sep 2010
Location: Planet Earth
Posts: 380
Unfortunately a google search for IRP9130 only returns hits to the "Practical guide to free energy devices" and to sites promising to offer datasheets but then saying "datasheet not found" when you follow the link to IRP9130.

All I can tell from the circuit diagram is that it appears to be a P-Channel Enhancement Mode MOSFET. I have some around, I think. I will try building this circuit.

Coil and capacitor design is another ball of wax entirely... I'm sure the reason most tesla coil builders don't see the resonance effects described in the document is because their primary is not phase conjugate (quarter, half, or full wave) to the frequency of the driver circuit and the secondary doesn't have the proper ratio to maximize energy transfer. Eric Dollard mentions the primary and the secondary should have the same surface area.

If the primary needs to be the right length to cause quarter, half, or full wave resonance, and the secondary needs to have the same surface area as the primary -- it's no wonder people have had difficulty reproducing power amplification through resonance. However since we know the conditions we are tuning for, we have a better chance than most!
__________________
 
Reply With Quote
  #7  
Old 10-05-2010, 04:14 PM
Joit Joit is offline
Gold Member
 
Join Date: Sep 2008
Posts: 1,992
Irfp9130

It seems like that there is missing the F,
and the one what may match is here.
http://www.datasheetcatalog.org/data...8/387350_1.pdf
After the Circuit Diagram it looks like it is a P Channel Mosfet.
__________________
Theorizer are like High Voltage. A lot hot Air with no Power behind but they are the dead of applied Work and Ideas.
Reply With Quote
  #8  
Old 10-05-2010, 06:49 PM
Jbignes5 Jbignes5 is offline
Gold Member
 
Join Date: Mar 2009
Location: NY, USA
Posts: 1,014
The truth about the Tesla Coils.

There is a section about the device that Don made and the proper way to setup a Tesla coil with the split primary and balanced primary unit. Most make the Tesla coil in the pure voltage mode which is on one of the ends to put the primary. When it is supposed to be in the middle plus most do not make it resonant from the get go. They take random length and make the secondary whatever they can stand to wind. Then try to tune the unit to an octave not in complete resonance with the rest of the system. This is an important step they are missing.
__________________
 
Reply With Quote
  #9  
Old 10-05-2010, 09:55 PM
7imix 7imix is offline
Senior Member
 
Join Date: Sep 2010
Location: Planet Earth
Posts: 380
Quote:
Originally Posted by Joit View Post
It seems like that there is missing the F,
and the one what may match is here.
http://www.datasheetcatalog.org/data...8/387350_1.pdf
After the Circuit Diagram it looks like it is a P Channel Mosfet.
Thanks a lot! That looks like it matches. Sweet. I am going to order some.
__________________
 
Reply With Quote
  #10  
Old 10-06-2010, 12:26 AM
7imix 7imix is offline
Senior Member
 
Join Date: Sep 2010
Location: Planet Earth
Posts: 380
I made the multiple spark gap described at the end of the document. Love it, now I need something to drive it.



Next I am going to build my first coil.
__________________
 
Reply With Quote
  #11  
Old 10-06-2010, 04:58 AM
ashtweth's Avatar
ashtweth ashtweth is offline
Gold Member
 
Join Date: Jan 2008
Posts: 2,493
Send a message via Skype™ to ashtweth
Thanks for that 7imix i wish i had more time to build most of Pat's stuff, he has done the essential to keep the research going..you cant find answers with out looking! Thank you for posting my friend.

Ash
__________________
 
Reply With Quote
  #12  
Old 10-06-2010, 11:30 AM
Jbignes5 Jbignes5 is offline
Gold Member
 
Join Date: Mar 2009
Location: NY, USA
Posts: 1,014
Quote:
Originally Posted by 7imix View Post
I made the multiple spark gap described at the end of the document. Love it, now I need something to drive it.



Next I am going to build my first coil.
Nice what about a marx generator?
__________________
 
Reply With Quote
  #13  
Old 10-08-2010, 06:56 AM
7imix 7imix is offline
Senior Member
 
Join Date: Sep 2010
Location: Planet Earth
Posts: 380
I made a low voltage version of the circuit I quoted above, the 555 based driver for the spark gap. I took some scope shots.

YouTube - Don smith trigger circuit

Sorry for the video being sideways.
__________________
 
Reply With Quote
  #14  
Old 11-13-2010, 04:42 AM
7imix 7imix is offline
Senior Member
 
Join Date: Sep 2010
Location: Planet Earth
Posts: 380
I finally got around to testing my multiple spark gap. I wasn't doing any spark related experiments for a while, but this multiple spark gap is spectacular and I'm glad I built it.

The video is really beautiful, check it out.

YouTube - Multiple spark gap
__________________
 
Reply With Quote
  #15  
Old 11-13-2010, 05:22 AM
Jiffycoil's Avatar
Jiffycoil Jiffycoil is offline
Senior Member
 
Join Date: Nov 2009
Location: Johns Island South Carolina
Posts: 189
Can I add more to my plate OH YEAH!

Hi Jbignes5 and others,
I've been reading A Practical Guide to Free-Energy Devices for a few weeks now after hearing about it in Energy from the vacuum. I could not be more delighted to get involved. It's kinda funny how there has been a synchronicity with my interests as of late. Thank you for starting this and giving it wings.
__________________
 
Reply With Quote
  #16  
Old 11-13-2010, 05:25 AM
Jiffycoil's Avatar
Jiffycoil Jiffycoil is offline
Senior Member
 
Join Date: Nov 2009
Location: Johns Island South Carolina
Posts: 189
Quote:
Originally Posted by Jbignes5 View Post
Nice what about a marx generator?
Nice job on the multigap 7imix . This is going to be interesting Jbignes5.
__________________
 
Reply With Quote
  #17  
Old 11-13-2010, 01:08 PM
redrichie redrichie is offline
Senior Member
 
Join Date: Sep 2009
Posts: 346
Hi Jiffy,
I have found that almost all of these technologies are related in one way or another. And a combination of these systems is probably whats going to get us over the top. The more Ive read into the ideas presented at this place the more I realize that it is all interconnected somehow. This particular thread seems to be right up your alley with the TC stuff however. Good luck guys.
Quote:
Originally Posted by Jiffycoil View Post
Hi Jbignes5 and others,
I've been reading A Practical Guide to Free-Energy Devices for a few weeks now after hearing about it in Energy from the vacuum. I could not be more delighted to get involved. It's kinda funny how there has been a synchronicity with my interests as of late. Thank you for starting this and giving it wings.
__________________
 
Reply With Quote
  #18  
Old 11-13-2010, 04:08 PM
thedude's Avatar
thedude thedude is offline
Senior Member
 
Join Date: Nov 2007
Posts: 381
Thanks Jbignes5

Wow. For now all I can say is fantastic stuff. I'm sure there are many of us who would like a pdf copy of this to have for future reference, so i made one up.

Thank you sooo much Jbignes5!

For a PDF copy download here, Donald Smith Practical Guide.pdf

I'm reading, reading, reading....
Reply With Quote
  #19  
Old 11-13-2010, 05:31 PM
SuperCaviTationIstic's Avatar
SuperCaviTationIstic SuperCaviTationIstic is offline
Senior Member
 
Join Date: Jan 2010
Posts: 334
Quote:
Originally Posted by Jbignes5 View Post
There is a section about the device that Don made and the proper way to setup a Tesla coil with the split primary and balanced primary unit. Most make the Tesla coil in the pure voltage mode which is on one of the ends to put the primary. When it is supposed to be in the middle plus most do not make it resonant from the get go. They take random length and make the secondary whatever they can stand to wind. Then try to tune the unit to an octave not in complete resonance with the rest of the system. This is an important step they are missing.
From what I've seen, I could find no evidence of Don ever using a split primary. Believe me, I searched and searched. It certainly is possible that in every case he did and it was hidden, but if so me NEVER took a single picture showing the wires coming and going from the same side.
His references to the Tesla drawings clearly indicate IMO that he had a secondary wound in opposite directions. I've not seen a single reproduction attempt with this configuration. Or is it possible that the capacitor across one half of the secondary changes the phase relationship between it and the other half, without needing to wind it in the opposite direction?
__________________
 
Reply With Quote
  #20  
Old 11-13-2010, 06:42 PM
sebosfato sebosfato is offline
Silver Member
 
Join Date: Dec 2008
Location: milan
Posts: 778
Reading this interesting documents, i concluded one thing.

He probably was creating a resonant tank at 40khz and than using a switching circuit witch take the magnetic fields and break them into megahertz frequency thus increasing the energy available.

E=F*H

So he had the energy stored in the inductor, and switched at higher frequency the circuit where this field is inducing. Or the receptor.
__________________
 
Reply With Quote
  #21  
Old 12-12-2015, 01:09 AM
Belangers's Avatar
Belangers Belangers is offline
Junior Member
 
Join Date: Jan 2010
Posts: 24
shielding

The only thing that has to be shielded is the spark gap, and, if you use the enclosed gap and a low enough voltage, you won't get an xray nor will harmful waves get you. I've messed with this now for a while and have figured it all out finally. The entire device can be covered in a grounded case (faraday cage), minus an antenna which only needs to connect to the wires outputting the secondary coil where the diodes connect. The other end of the coil goes to ground, and, to my surprise, it doesn't even need to be grounded if the primary coil is one turn and the secondary 100 because the rectified ends of the coil can connect to two separate, isolated antennas mounted to your car (isolated from the chassis of course, and protected from flashover from a good dielectric and rain shields. The other end of the coil can go to the ground of the battery and a ground strap from the chassis can touch the ground to create the same, if not even more energy since the difference in potential acts like it's a greater distance apart from the elevation that the amperage nearly quadruples in the circuit. We only have to favor one end of the coil after it starts operating with a load since the tuning can be adjusted after a load is added to the output. Once the device is loaded, the battery could be disconnected and it will run itself. The key secret is the device that is at the end of the system. I figured it out and he insisted that the device didn't need to be used. That device adjusts the frequency for him, it uses an inductor coil, and, on the inside of the tube is a capacitor. It's the frequency adjustment filter that is obtained by matching the frequencies on the chart given in his pdf, however, the chart is wrong. There are online calculators to figure this out online, and, they are accurate as well.

Good luck, it is worth it's weight in gold because it replaces hydroelectric, solar, wind power , oil, gas, coal, and of course the ridiculously expensive paid for electricity. Don sold the technology to generating companies that are owned by energy companies, oil companies, etc., in the effort to eliminate fossil fuels and offer a free enrgy device without giving all of the secrets away, however, it took me years to gather the info and parts as some of the parts are difficult top even find, however, leyden jars will work just fine if built large enough. Government has done their all to threaten folks over it, however, they can't do much to those using these overseas!

My device was grounded in a stream nearly 200' lower than my lab, and, I built a curled copper antenna connected to an isolated high dielectric mica coated insulator I made from microwave shielding. The antenna was 30' over my roof and ground was 200 plus feet driven deep into my stream below me. The difference in potential would have been 1200 volts, however, I utilized the end of the coil which he stated was to build amperage, so, I have a massive difference in amperage, from 1/4 the added voltage to 1/8 more amperage. The current is so much that I use what I need, I can't possibly bog down the source, it's an absolute home run!

I use an older nst from ebay, and, an EPSCO 5500 volt enclosed gas discharge tube for the arc along with 5000 watt microwave oven diodes, connected in parallel. The output will create fireballs in a shorted condition, and, since it is made from cold electricity, the highh voltage is dangerous, but not nearly as devatstating as the stuff the utility company uses. I forced the system to run an output of 35,000 watts driving many of my neighbor's appliances, lights, irons, blow dryers, etc., all higher amperage devices and the device modified it's current to suit their operation, almost as if it were listening to what it needed. The circuit is amazing.. It certainly has a bunch of Tesla built in!!

DO NOT FOLLOW THE ONLINE DIAGRAMS!! ALL OF THE DEVICE's IMAGES ARE ONLINE TO MAKE IT FUNCTIONAL.. All we need to do is to connect all self healing caps of the correct value together to invite the flow of amperage for the coil that it's connected to .. the top coil is the amperage coil!

Good Luck To All! I have many answers. Please ask away..

I just pray daily to thank Don for being able to share before he passed on..




Quote:
Originally Posted by gmeast View Post
Hello Jbignes5,

I searched for this information by Don L. Smith ... I can't tell you for how long. Thanks for this info'

Do you have any idea how potent a statement the above is ? This is probably where many folks give up or simply can't connect the dots.

... THINGS MUST BE PROPERLY SHIELDED ... and much MORE than that ... THE RIGHT THINGS MUST BE SHIELDED IN THE RIGHT WAYS ...

Again, thanks,

Greg
__________________
 
Reply With Quote
  #22  
Old 12-12-2015, 02:00 AM
BroMikey's Avatar
BroMikey BroMikey is offline
Platinum Member
 
Join Date: Jan 2013
Posts: 4,199
Quote:
Originally Posted by Belangers View Post
The only thing that has to be shielded is the spark gap, and, if you use the enclosed gap and a low enough voltage, you won't get an xray nor will harmful waves get you. I've messed with this now for a while and have figured it all out finally. The entire device can be covered in a grounded case (faraday cage), minus an antenna which only needs to connect to the wires outputting the secondary coil where the diodes connect. The other end of the coil goes to ground, and, to my surprise, it doesn't even need to be grounded if the primary coil is one turn and the secondary 100 because the rectified ends of the coil can connect to two separate, isolated antennas mounted to your car (isolated from the chassis of course, and protected from flashover from a good dielectric and rain shields. The other end of the coil can go to the ground of the battery and a ground strap from the chassis can touch the ground to create the same, if not even more energy since the difference in potential acts like it's a greater distance apart from the elevation that the amperage nearly quadruples in the circuit. We only have to favor one end of the coil after it starts operating with a load since the tuning can be adjusted after a load is added to the output. Once the device is loaded, the battery could be disconnected and it will run itself. The key secret is the device that is at the end of the system. I figured it out and he insisted that the device didn't need to be used. That device adjusts the frequency for him, it uses an inductor coil, and, on the inside of the tube is a capacitor. It's the frequency adjustment filter that is obtained by matching the frequencies on the chart given in his pdf, however, the chart is wrong. There are online calculators to figure this out online, and, they are accurate as well.

Good luck, it is worth it's weight in gold because it replaces hydroelectric, solar, wind power , oil, gas, coal, and of course the ridiculously expensive paid for electricity. Don sold the technology to generating companies that are owned by energy companies, oil companies, etc., in the effort to eliminate fossil fuels and offer a free enrgy device without giving all of the secrets away, however, it took me years to gather the info and parts as some of the parts are difficult top even find, however, leyden jars will work just fine if built large enough. Government has done their all to threaten folks over it, however, they can't do much to those using these overseas!

My device was grounded in a stream nearly 200' lower than my lab, and, I built a curled copper antenna connected to an isolated high dielectric mica coated insulator I made from microwave shielding. The antenna was 30' over my roof and ground was 200 plus feet driven deep into my stream below me. The difference in potential would have been 1200 volts, however, I utilized the end of the coil which he stated was to build amperage, so, I have a massive difference in amperage, from 1/4 the added voltage to 1/8 more amperage. The current is so much that I use what I need, I can't possibly bog down the source, it's an absolute home run!

I use an older nst from ebay, and, an EPSCO 5500 volt enclosed gas discharge tube for the arc along with 5000 watt microwave oven diodes, connected in parallel. The output will create fireballs in a shorted condition, and, since it is made from cold electricity, the highh voltage is dangerous, but not nearly as devatstating as the stuff the utility company uses. I forced the system to run an output of 35,000 watts driving many of my neighbor's appliances, lights, irons, blow dryers, etc., all higher amperage devices and the device modified it's current to suit their operation, almost as if it were listening to what it needed. The circuit is amazing.. It certainly has a bunch of Tesla built in!!

DO NOT FOLLOW THE ONLINE DIAGRAMS!! ALL OF THE DEVICE's IMAGES ARE ONLINE TO MAKE IT FUNCTIONAL.. All we need to do is to connect all self healing caps of the correct value together to invite the flow of amperage for the coil that it's connected to .. the top coil is the amperage coil!

Good Luck To All! I have many answers. Please ask away..

I just pray daily to thank Don for being able to share before he passed on..


WOW thanks for the open door Belangers

My name is Michael Rowland I am 58 yrs old and wish to understand
the Don Smith device better. Which diagram do you recommend?

If I understand correctly the Don Smith device raises the voltage
and frequency with a series of coils to get the freedom from the
resistance by HIGH VOLTAGE.

Then after the spark gap Don showed in one video how he filters
the High Voltage and High Freq back down to 60hz. I see what might
be bucking coil arrangements but I don't know much.

This reminds me of the people who used a neon sign transformer
then shot that to a TESLA coil but Don reverses the process for
stand 60hz operation and comes out with more than he started
with.

Of course the grounds and antennas are not to be dismissed as
they play a big part of providing a pathway for energy to flow
into the HV field that is being generated.

I am all ears SIR. I saw all of your other previous posts and wondered
show I but in thinking maybe this might not be the best time.

I'm out here in Central Kansas with the wheat farmers.

I use the handle "BROMIKEY" because it is easy for folks to distinguish
between mike and mike's and more michaels
__________________
 
Reply With Quote
  #23  
Old 12-13-2015, 06:15 AM
MorningStar MorningStar is offline
Junior Member
 
Join Date: Sep 2013
Location: California, USA
Posts: 22
Hi Belangers:

First, let me say, this is the most eye-opening post I've ever read on this forum regarding the work of Don Smith. You've obviously spent an incredible amount of effort into understanding Don's work.

If you don't mind indulging a few questions, I've attached a diagram for reference.

Your seem to describe two systems, one system has two antennas and a ground, which under certain circumstances is not required and second, described more detail uses a roof antenna and ground in your nearby stream.

My questions:

1. Does my diagram accurately show the two antenna and optional ground set-up in concept form?

2. Does my diagram accurately show the inductor coil (primary?) and capacitor inside the tube? I assuming you are referring to the picture of Don's device with movable primary wrapped on a 1 to 1.5 inch PVC pipe.

3. How difficult is this thing tune? Building it trivial and no problem to do the tank circuit (RLC) frequency calculations, but we soon leave the domain if RF engineering with the secondary coil for the world of radiant / cold / static energy (call it what you will).

4. What about putting a tuning capacitor across the secondary to tune it to resonant? Don does this on his models.

5. Any benefits of using a center-tap to ground on the secondary or doesn't really matter?

Any insight would be appreciated, as your've the first person I've seen on this forum who really understands Don's work.

All the best, Roger
Attached Files
File Type: pdf Belangers1.pdf (26.3 KB, 64 views)
__________________
 

Last edited by MorningStar; 12-13-2015 at 06:22 AM. Reason: typo
Reply With Quote
  #24  
Old 12-13-2015, 04:18 PM
AetherScientist AetherScientist is offline
Senior Member
 
Join Date: May 2011
Posts: 462
I am still learning from Don Smith theories and I have replicated a few of his simple circuits like the one that he shown using a car's ignition coil and one plate of the capacitor. He proves that in the other plate you can receive energy.
That is true as other simple circuits.

The main problem I think it is a bad understanding about how Smith's systems work.

Also, there are different circuits and not just only one as most people want to believe. All is said in his videos and documents. It would be better is he would explained a little bit more, but there is enought information to start performing some tests and trying to approach to the most-known circuit.
__________________
 
Reply With Quote
  #25  
Old 12-13-2015, 04:24 PM
AetherScientist AetherScientist is offline
Senior Member
 
Join Date: May 2011
Posts: 462
For example Don Smith is using like a more advanced form of Avramenko Plug to charge the big bank of capacitors.

And also he is using a logarithmic scale to perform measurements instead the classic linear measurements. The scales that he uses are different.

I think he charges quickly a bank of capacitors using a resonant system. I have performed some tests and I can charge a bank of capacitors using 3 wires instead of 2 wires. You see how they charge faster and the charge is more powerful.
__________________
 
Reply With Quote
  #26  
Old 12-13-2015, 06:39 PM
med.3012's Avatar
med.3012 med.3012 is online now
Silver Member
 
Join Date: Nov 2012
Location: Algeria
Posts: 751
Donald Smith device is based on a resonating system, but that system must turn the space surrounding it into a source of power by attracting ambient electrons with the resonance frequency speed, more frequency mean more power, Lenz's law is critical in his system and have to be avoided if we want to achieve OU device...




tuning process isn't difficult if we could achieve the resonance since we are working with electrostatic induction, standing waves will be a part from his system automatically ...
__________________
 
Reply With Quote
  #27  
Old 12-13-2015, 07:05 PM
AetherScientist AetherScientist is offline
Senior Member
 
Join Date: May 2011
Posts: 462
Hello med.3012

I am drawing some schematics to better understand what I mean. I think Smith's system is a step-up transformer + advanced AV plug. It will take some 30 minutes to finish the drawing.
__________________
 
Reply With Quote
  #28  
Old 12-13-2015, 07:44 PM
med.3012's Avatar
med.3012 med.3012 is online now
Silver Member
 
Join Date: Nov 2012
Location: Algeria
Posts: 751
Quote:
Originally Posted by AetherScientist View Post
Hello med.3012

I am drawing some schematics to better understand what I mean. I think Smith's system is a step-up transformer + advanced AV plug. It will take some 30 minutes to finish the drawing.
Hello AetherScientist,

yes i agree it's a step up transformer but the overall power depend on the voltage in the primary because it's responsible for ambient electrons attraction, more voltage mean more power, the length of wire in both side have to have a proportion, the primary is the quarter length of the secondary, so we don't have to worry about the used frequency in the primary reactor coil if the correct induction is used ( electrostatic induction = a kind of electromagnetic induction where electrostatic force is a part from the induction waves, this mean there is a standing waves regardless the frequency used ! )
__________________
 
Reply With Quote
  #29  
Old 12-13-2015, 07:57 PM
AetherScientist AetherScientist is offline
Senior Member
 
Join Date: May 2011
Posts: 462
A brief visual explanation

__________________
 
Reply With Quote
  #30  
Old 12-13-2015, 08:06 PM
AetherScientist AetherScientist is offline
Senior Member
 
Join Date: May 2011
Posts: 462
Quote:
Originally Posted by med.3012 View Post
Hello AetherScientist,

yes i agree it's a step up transformer but the overall power depend on the voltage in the primary because it's responsible for ambient electrons attraction, more voltage mean more power, the length of wire in both side have to have a proportion, the primary is the quarter length of the secondary, so we don't have to worry about the used frequency in the primary reactor coil if the correct induction is used ( electrostatic induction = a kind of electromagnetic induction where electrostatic force is a part from the induction waves, this mean there is a standing waves regardless the frequency used ! )
It depends on a lot of different things, one thing is the thing you say.

Smith explains that when using resonance in AC there is not impedance (resistance), so there is superconductivity at ambient temperature. When there is not impedance, Ohm's law doesn't apply.

High frequency I think is more important than high voltage because while using HF the electricity travels around the wire, so there is not wire resistance, the second factor to avoid resistance is that impedance = 0 (no resistance). So in this case of superconductivity there is not a random bouncing of electrons (dissipation). Also, instead of linear scale (resistive case), it's applied a logarithmic scale (superconductivity).
__________________
 
Reply With Quote
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



Please consider supporting Energetic Forum with a voluntary monthly subscription.

For One-Time Donations, use admin@ this domain > energeticforum.com

Choose your voluntary subscription

All times are GMT. The time now is 11:55 PM.


Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimisation provided by DragonByte SEO v1.4.0 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Shoutbox provided by vBShout v6.2.8 (Lite) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
2007-2015 Copyright - Energetic Forum - All Rights Reserved

Bedini RPX Sideband Generator

Tesla Chargers