SORRY VIDBID FOR NOT ANSWERING YOUR QUESTUINS

I See Alot Of Extra Parts That Don Put In . But My Schem Works.

I Plan Doing Some More Work Time On The Device.

I Just Thought It Would Be Interesting To Everyone That It Will Work Ubder Different Paramaters(not Sure Of Speling).

Its Been Thirty 4 Years Since School And Don't Recall A Lot Of Things.

Do To A Serious Injury Years Ago.

The Welding Rods Came From Tsc Hardware Wjere I Live.

If You Have More Questions I'll Beglad To Answer.

Vidbid

One Other Thing I Have Built Don's Schematic And I Could Not Get It To Function.

Maybe I Made A Wrong Design On His Schem. But I Was Uable To Get It To Work.

Regards

Slow-n-easy

Sure, no problem. I'm just using paint, too.

Regards,

Vidbid

Hi all

Hi Dragon

yep i am very near of your work now. Fantastic motivating results

I could finally connect the ground to the kacher output. And the result is really great.

The most problem is the variable cap between the 2 leads of the secondary coil .

Just for my first experiment i enclose how i did it.

Very simple , i cut a HD disc in 2 half (with a dremel cuting disc ). than i put a heavy paper as dielectric . between the 2 half and than you can easily increase or decrease the capacitance by covering more or less the 2 half disc. Very efficient for this particuliar use.

Have to make all of this much more stable and tunable , because the system is very sensitive.

hope this helps

Good luck at all

Laurent

Attached Images

	variable-cap-1.jpg (15.3 KB, 73 views)
	variable-cap-2.jpg (8.5 KB, 69 views)

I assume that it is possible that the inverter could work some of the time on the alternating current from L2. I mean half of the time the current would be in the correct direction to power an inverter.

It's an interesting design.

Maybe somebody will step forward with a replication of your design.

Only I can't do it as I working on building woopy's design of his radiant exciter (which I can use to radiantly excite two lead acid batteries and to use his coil design to radiantly excite the captret being used in windfilter's design).

Regards,

Vidbid

Hi Woopy,

I really enjoy your videos.

I was wondering if you have tried placing a over-sized copper plate between the batteries (as in windfilter's video) and connecting a lead from it to your captret inside your exciter coil.

If you do, could you please share your results?

Regards,

Vidbid

Hey Vidbid

Are you a time traveler too. your modification 2b is dated 4-18-2014

Just kidding

Attached Images

modification2b.JPG (57.3 KB, 87 views)

Very nice PDF, JohnStone.

It would be nice if there was some experimenter out there who would be willing to attempt replication.

Regards,

Vidbid

LOL

I was wondering when somebody would catch that.

I guess I'm human, too.

Regards,

Vidbid

¨Hi Vidbid

Of course i did it with really interesting results

And i can say to you and to all other contributors here that this Dragon's video is really a practical reality .

It took me almost 2 days of experimenting to approach what Dragon offers to us in that video.SMOV0006_MPEG_.mpg - YouTube

This guy really has some good understanding , based surely on a lot of experimenting of what we are looking at.

All the shematic are already given here in this thread

All you need to do is to replicate exactly as per the shematic that i ( and also
you) posted some post ago.

Next video soon

hope this help

laurent

hey there african

i looked up the size of the bobbins if you still need it.the cor is 10mm x 13mm

x10mm high topis18.5mm x 21.5mm base is 22mm x 26mm four leads 15mm

and 20mm spacing cat#bn-1 if you want to see for yourself.

good day my man

Hi Johnstone

Your Pdf Is Amazing. You When To Alot Trouble For It & I Appreciate That.

Good Day Sir

Slow-n-easy

Hi All

Here is new schem that Vidbid made that is so amazing

But I have made another input to the device

And that is (4) .01 uF 4000 volt capacitors in parralell

It works without them but I am going to test some more with these caps

Good Day People

Attached Images

new don smith suit case device.JPG (36.2 KB, 102 views)

Very nice woopy ! Quite creative with the adjustable cap, excellent work. I was hoping you would be able to get to the point where you see the circuit ultimately come alive.

If you calculate the energy in the cap and multiply it by the discharge rate you should be able to get a reasonable output calculation, certainly not accurate but a good idea of what your dealing with. You can use a sniffer coil on your scope probe at the cap discharge to find the discharge frequency.

Keep up the great work ! Your closer than you realize....

Hey Vidbid

I have question. how did you make everything so straightand prporsion so exact? Also I put a Cpacitor Bank of (40),01 uF and 4000 volts and then i'm

thinking about adding a voltage divider to the negitive right after the coil. Another thing is you put in # of turns on the coils and I used 5feet and 320

feet and wound until I was out of wire. then I made my connection the same lenght. I don't know if that is signicatant or not. But thats the way I have

been winding my coils no regards for my coil # of Turns. I learned this from a electrican on the internt and it has been working for me . He didn't have to

have capacitors in his circuits also.He said it had to do with wavelength measured in feet.

food for thought

SLOW-N-EASY

He references a plug. Looks like one side goes to ground and the other back to the transformer. What appears to be a single wire to the bulb is likely an extension cord.

One wire electricity is simple. Even electrons with virtually no mass still have inertia and can have a significant amount of kinetic energy when moving fast enough. Think about electrons like a gas...Tesla did. Once you see electricity in terms of inertia and compressibility, all manner of 'magic' is possible.

Hey Johnstone

I have some answers to your question on your pdf.

Battery:sealed lead acid
Brand: Tysonic 12v 5 amp

Transformer:Liteglow Industries
1291 sw 27th ave
Pompano Beach , Fl 3306
1 800 801 4569
LowGlow series
12 volt 5 amo input
9500 volt 30 ma output
40 khz

Spark Gap: (3) copper eletronics adjustable holder
3 post per spark gap usind # 10 bare copper ground wire
1" or 25 mm long

Coils:minni bobbin purchase from allelectrics.com
plastic bobbin 4 post ready for circuit board and soldered
L1 4.89 turns # 26 copper mw mounted on top of L2
L2 310 turns # 30 copper mw
L3 310 turns # 30 copper mw
L4 4.89 turns each # 26 mw (1) cw (1) ccw on top of L3 center tapped to ground

Wire: purchased from Allelectronics.com
# 30 & # 26
Enameled magnet wire

Cooling fan: 12 volt 40 mm
Sunon Maglec# kde1204pfv2
1 watt
40 x 40 x 10mm
7.0 cfm 27 dba 2-2,3" leads

Welding Rods:1/4" or 6mm
Copper Coated SoftSteel Core
Howbart Manufacturing
Purchase from TSC Hardware
RG45

Lighting: 30 watt
Floresence
110 volt
inclosed in lamp holer

Hope that wath youneeded for your pdf

Good Luck & Best Wishes

SLOW-N-EAST

HI EMCSQ

THE PLUG I MENTION IS METAL ENCLOSED LAMP WITH CORD AND PLUG

I JUST I WIRE GOING TO MY DEVICE OUTPUT AND THEN A EARTHED GROUND GOING TO ROD DIVEN IT THE GROUND OUTSIDE THE HOUSE THROUGH DRYER VENT THAT I AM NOT USING.

i'M GOING TO TRY TO GET WHAT PARTS I NEED FROM ELECTRONICS STORE SO I CAN DOWN LOAD SOME PICTURES OF MY CAMERA PHONE.

NOT SURE WHAT I NEED BUT MAYBE THEY CAN HELP. SEEMS TO ME I NEED PLUG FOR MY PHONE AND A USB CONNECTION FOR MY COMPUTER ON A CORD

BUT i DON'T KNOW IF ANYTHING LIKE IS AVAILABLE. aLSO i SURE i WLL NEED SOME SOFTWARE FOR THE COMPUTER TO READ THE DATA

REGARDS

SLOW-N-EASY

Hi J.S,

Very much impressed by they way of your analysis for replication.
Your efforts are much appreciated.
Hope you got answer for all of your questions in doc, and your hard work will be fruitful for others.

Thanks and regards,
D.J

Hi SLOW-N-EASY

You can go to any cellphone shop and just tell them that you want to connect your phone to your computer as a modem to connect to the internet and that you want the usb cable,it normally comes in a package with software included,
it should be cheep in SA it's about $3.

Can you tell me if your device runs by itself or do you have to use the batt
to keep it running.
Thanks

Best Johan

@Slow-N-Easy:
- Thanks for your answers I will add them to the doc and will continue asking.
- Please forward the type of your phone in order to evaluate the chance to connect it to your PC

@woopy:
Nice idea with your variable cap.
If you need more you can follow my instruction for using aluminum foil glued into document pouches. 10nF per pair / half letter size. You can glue the pouches with a flat iron as well or a hair dryer. Because of glued edges you will have no corona effects.
By adding elements you can adjust to the capacity required.
You may give them a fulcrum and operate a stack of them.
You may add bare pouches between the elements for increasing voltage above 15 KV

HeyJ johnstone

My phone is an LG. Your detail on your pdfis really superb. You must expensive software.

Later

slow-n-easy

Hi SnE, I am persuing, it's my job in real life as well.

- What LG type exactly? Open the back cover of the phone and you will see the model number of the phone. Post the model number. see i.e.
- What opration system on your PC (Win2000, WinNT, WINXP, Win7, MacOS, Linux or derivate...)
- My - sorry YOUR - doc was made with normal MS-Word. But as my job in real life is writing specs I have nice templates at hand which I knead and fill in facts. The structure and printing form is widely automated. The doc was 4 hours of work - every minute worth in order to spread exact facts.
- You might try KiCad for drawing schematics (it's open sourece and free) sample

Howdy African

I'm Still working on it to get the bugs out.I'll work on it tonight on that particlar part of circuit. Also

I have added a cap bankr to the device (5) .01 uF 4000 volts each. and its working great. If anyone

has a device that flshes on for a second and then shuts down and keeps repetting. you need to switch the leads , one one

to ground and one to rhe plug you are trying hope this this helpssome. I just found that out while

working on device.

Attached Images

new don smith suit case device.JPG (36.2 KB, 134 views)

HI
the shematic is ok the oscilator for 60hz is like this you may find in the old converter from 12v to 110v this is basic simple ciruits and block shematic and is true ... but all here is missing here all this devices << T.K D.Smith.. and athere similar to >
what is vrong in this shematic nothing all is there all is here .. but is not working like <cop 1.>2 or more
all this years you may turn and turn around and still waste time ...
i say is the raid way to make don smit device whit this sheme.. if some one find the something is missing then whill work just very powerfull... .. and stilll whill be keep in the secret box...

and all we are alone here we are working for its self .. if some one has done and reply then still be no open to all people ... adn then we whill never see the working devices here ... but only whill be good here is the make more friends for to drink some coffe or beers and speak some story of how is made free energy devices free enrgy devices s dont true nothing is free the word free is no good to say i whill say is the we are take what is there all whit more eficient ..... and convert to our porpose..

Hi xxxyyyzzz.
Welcome.

I don't get it! What are you trying to say and what device are you talking about
please specify.

Regards Johan

Howdy SLOW-N-EASY right back at you Ha Ha

I am not chasing a 10Kw device i am looking for a device that can achieve just
unity in other words say 50watts in and 50watts out. then the prospects becomes endlessly, so i support what you are doing and i am going to try and
replicate on the information that you have posted so far.

The best to you
Johan

HI SlowNEasy thanks foe sharing this schematic. Regarding transformer an MOT would be good just add 10turns ct? and what one should do for 50hz output?
Thanks.

It is still confusing on second part where transistors are in flip-flop circuit. You are feeding in AC pulsed signal into that part and transistors only work correctly on DC power... Is it missing rectifier bridge before transistors?