another thought is the importance of battery and cfl also are negative resistor

in my test it run better with battery fully charge respect a a 12v 1,5 amp dc power pack

heres a fab page about viktor >>>THE NATURAL PHENOMENA OF ANTIGRAVITATION AND INVISIBILITY IN INSECTS AND THE GREBENNIKOV CAVERNOUS STRUCTURES EFFECT

Thanks stringguy - yes that is the same I saw short while ago on TV documentary. Interesting.

Bodkins, A bit late, I just looked at your video "Big Sparks"
check your coil - the insulation 'bakelite' - it is possible (likely) that the insulation around the HV terminal is cracked. That is usually where you had problems in the old days - car engine not starting.

Just uploaded new video - Original circuit BUT all new parts.

Running in this video is dual set from one battery Now have 1x2222A, 1x3055 master and 4x3055 slaves.

Meter tested and verified with Fluke at same readings. I only have two digital meters that can read this low. Multimeter on singe supply line from Battery positive through meter to transistor array.

10 Mili Amp analog barely moved indicator.
1 Micro Amp = 0.000001 Amp

Run cool – on 12 MICRO Amp
All together 5x 18W CFL, 1x18W Fuorecent tube

Then second half I added battery in series pushing 24 Vdc
Extreme bright lights and drawing 60 Micro Amp Same load

Aromaz 017 – Dual DRE test run on 24Vdc
YouTube - Aromaz 017 – Dual DRE test run on 24Vdc

BUT BE AWARE: I am running on 24Vdc only for short period. 19.4 Vdc get to coil terminals - the coil is in effect OVERLOADING. After some 20 to 25 minuts the coil is hot and I can hear sparks flying inside - also lights get some real strong spikes. After about 30 minutes, frequency drops to under 30 hz and lights are flashing like disco.

Hi, Corrie

Thanks for all your hard work, its now included along with Bodkins and lid's new stuff in there..Ren is next after we sort some bugs

http://www.panaceauniversity.org/Tes...Oscillator.pdf

Ash

YouTube - Bodkins 35 diode ground.AVI


WHAT MORE CAN I SAY.
Aromaz Looks Like you ARE resonance with the planet

Here is link I found that does look interesting Thomas Henry Moray: Speech at Valley State College, Northridge CA.

Especialy I was interested in this part:
"Oscillations by synchronization are started in the first stage of the circuit of the device by exciting it with an external power source such as the difference of potential between two points. The circuit is then balanced through synchronization until the oscillations are sustained by harmonic coupling with the energies of the Universe. The reinforcing action of the harmonic coupling increases the amplitude of the oscillations until the peak pulses "spill" over into the next stage through special detectors or valves which then prevent the return or feedback of the energy from the preceeding stages. These oscillating pulsations drive each succeeding stage which oscillate at a controlled frequency and which are again reinforced by harmonic coupling with the ever present energies of the Cosmos. That is, the first stage drives a second stage, the second stage driver a third and so on. Additional stages are coupled or until a suitable power level at a usable frequence voltage and amperage is obtained by means of special resonant oscillators."

Excellent work Aromaz ... just microamps for all those bulbs

I saw your video and did not realize you were a member here. I sent you a message through youtube requesting a circuit diagram to which you can ignore as you maybe posting it here.

I would like to replicate your setup and wanted to know if the transistors are just all hooked up in parallel?

Thanks for sharing

Luc

@mlurye
Thats brillant,

@Aromaz I also have diso lights with my setup looks like its feedback of the energy.
Yes it is the insulation is crap but its the back radiant energy because of the potential in the coil with the inverted setup it gos to the postive of the battery (make and break) its the biggest spark I get.
Im Working on new way of pumping stuff around,
Will rep your stuff and post soon too I need shades by the looks of it!
For tomorrow

Aromaz, this is SOO amazing
So much light on this much energy input. Even if the system consumed miliamps instead of microapms, it would still be SO amazing. That means that you are lighting up to 100w worth of light using virtually no power at all. You could light this up from some AAA batteries Interesting that on 24V you get the coil to heat up, that is also a form of energy you know And I doubt that you could do this with microamps in conventional way.

Thank you for sharing.
Can somebody please send me a circuit for this or point me to the exact forum page where it is already posted? Thank you.
You guys have done an excellent job!

[quote=Bodkins;36932]@mlurye
Thats brillant,

Yes it does sound brilliant Sounds like Moray invented radio that is able to produce kilo watts of energy

There's a circuit back on page 43.

Thank you slayer007

Hi all

I tried Aromaz single coil setup with two CFL lamps, 4 transistors plus 2N2222 tonight and it fires up every time and I can smell the ozone and can draw long plasma like arcs. However my current as measured on my AVO8 analogue meter is around 150mA @ 24v = 3.6W. This current looks to be about what I would expect for the level of brightness I can get from the two lamps. I've tried reducing this with an adjustable spark gap but cannot get it lower without a corresponding reduction in brightness. Is anyone else having this problem? My earth only slightly increases brightness, so I'm wondering if the type of earth is very important in order to run the lamps like Aromaz at just a few microamps.

Hoppy

I also agree with you Jetijs that heat would also be great I wouldn't mind heating my hot water as I light my home

Most excellent news

Thanks for sharing

Luc

I have a theory about what happening to our transistors. Essentially same thing that happening to batteries..

Basically a N-P-N transistor is made up of a conductor (N) -the collecter, a semi-conductor (P) -the base, and another conductor (N) -the emitter.

The semi-conductor has minuscule holes in it, about the size of electrons.

Electricity wants to flow from N through P to N. It can only do this when voltage is supplied to it, and electrons fill up the holes of the semi-conductor, allowing current to flow. By using a square wave, we are able to get the short sharp shut off of pulsed voltage, that speeds ahead of the electron flow which bunches up at the instant of switch closure. Thus we are able to cause concussions in the aether of the smaller aether (pure voltage) which behaves as an incompressable gas.

The semi-conductor (P) does not initially become affected by these pure radiant pulses, as the aether particles are too small to plug up the holes. Hence the system won't pulse from radiant energy to begin with.

But when we condition the atomic lattice of the semi-conductor with electron current super saturated with above normal concentrations of the smaller aether particles, say, from an imhotep fan like I did, then we begin changing the atomic latticework of said semiconductor and just like conditioned batteries that more readily accept the 'fluffy' charge of pure voltage saturated electron current...

the P in the N-P-N begins to react to longitudinal compression waves of the aether that it itself is causing by being able to switch off on off on at high frequencies, giving square wave dc pulses.

HOWEVER, and unfortunately for us, one of two things are happening;

1: the semiconductor becomes saturated with aether particles - does the high voltage field picked up by lidmotor's christmas light tester grow over time or does the space he is working in become saturated with this field with more ease over repeated experiments? - I myself noticed my transistor driven ignition coil continued to oscillate at about 40hz when it was supposed to be off -
Therefore, does the semiconductor start getting to the point where it stops switching entirely off, reducing the square wave to a sine wave and thus reducing the bunching effect - so Aromaz's high voltage wire from coil stops going below room temperature etc.

2: OR, (or perhaps and then) does the semiconductor saturate or have atomic lattice altered to the point that the electron holes become so small that electrons won't pass, and we have a dead transistor.. ?

To whit: maybe we should try P-N-P transistors? Although I have a feeling they won't respond to 'positive' aether waves, I have long suspected that electron current causes two flows of aether current, one slightly negative, mostly neutral aether particle flowing back through the system (ie from ground) - this would be the smaller of the two 'lighter than hydrogen' atoms predicted by mendeleve's equations, by virtue of the size needed to flow back thru a system.

The other predominately positive aether particle travels along, caught up in electronic flow and 'stuck' to it by virtue of opposite charge. We can separate these two 'at the instant of switch closure' because the small aether particle can travel virtually instantly at least the speed of light, while the larger electron takes a while to get going, and unless hugely impacted in a high energy collision in a vacuum, ie how X-rays are made, will crawl along thru system at an inch an hour or whatever. I believe this is why the P in N-P-N has to be wafer thin, and is the reason for the fraction of a nanosecond it takes for transistor to switch off or on.

@bodkins, this two particle flow in opposite directions is the 'theory' I alluded to in page 2 and 3 of earth battery thread, when we were trying to work out how/why two diodes - one to ground, one from ground - seemed to increase brightness of neon from capacitor that was being charged over air gap from pulsing wire coming for ignition coil.

I believe that a diode can partially shut off the larger mostly positive aether particle's flow (looking at what happens to transistors, at least for a while, until semiconductor material is eventually rendered ineffectual) but cannot shut off flow back thru system of mostly neutral aether particle, which tries to fill in the gaps between longitudinal compression waves of positive aether particles. This explains how the 'natural medium' can have longitudinal compression waves, and still 'behave as an incompressable gas'.

Remember, tesla said 'behaves as', not 'is'.

Any compression waves of larger aether particle travelling out will cause smaller particle to tumble/flow IN, thus each stream of particle induces a flow in the other. When we momentarily block one in the dual diode setup, we don't block the other, & thus the one we are blocking has other particles that haven't been 'blocked' rush in to fill the gap. This 'extra' flow only happens around the diode's superconductor or the point of blocking. Then this 'extra' flow grabs more electrons from the wire....

Viola, the neon is brighter.


So to conclude this rambling, we can condition transistors & diodes like we condition batteries. They will for a while 'switch' at radiant impulse & eventually saturate & stop being able 2 shut off as quickly, & we lose our effects.

so, I'm going to use vacuum tubes. Semiconductors no good, but helped me understand exactly what's happening, hope can use knowledge..

If that is indeed so and someone else can verify this (I am not calling anyone a liar here), then it is true overunity and one of the most amazing thing I have seen. Big thanks to Aromaz for his incredible work. He has inspired me to catch up with the amazing work on this thread and to start experimenting on this again. So much to do, so little time.

When we touch base of transistor, or hold hand near it, we are increasing capacitance (or supplying a few electrons) - the extra capacitance as we know catches aetheric waves, either natural frequencies or our own created ones. These aether particles grab electrons and feed them to semiconductor (P), and switch goes on. Over time as atomic latticework of semiconductor alters to respond to positive aether particles, capacitance required would be less, and the system gets ever more touchy.

I too, am going to start playing with vacuum tubes.

Carl

No, I'm brian, and so's my wife :-)

i have wondered for quite a while why not many people experiment with vacuum tubes especially when i think edwin gray did and Tesla apparently did with his car....makes a lot of sense to start experimenting with them

come to think of it we are actually given the apparent part number Tesla used in his car

12 Vacuum Tubes (70L7-GT rectifier beam power tubes)

this is from the link that aromaz posted on the previous page.....

If I'm right, a conditioned battery or capacitor will spontaneously charge, wether in naturally existing longitudinal compression waves in the aether (that's getting boring to write. Abbreviated : lcw) or artificially created ones.. While a non-conditioned bat or cap will not. It's possible tesla didn't know this, his tower probably conditioned everything for miles around. I can't remember who was collecting natural waves from aether using big metal sheets on their roofs to a cap and diodes, or even if they were on this group, but their movies are on youtube. If the caps were conditioned with super high frequency dc pulses of lcw, maybe would work better than unconditioned cap setup too.

If someone is going to their local for new parts, cap/bat could they test this? My parts all been in this field and I'm flat broke right now so can't do.. As usual, must live vicariously.

this is probably silly, but the thing that stood out to me reading about the tesla car was the box and rod measurements:

24 inches long, 12 inches wide and 6 inches high. Two rods 1/4" in diameter stuck out of the box about 3" in length.

24,12,6,3 hmmm its prob nothing...dont mind me,

It is also interesting to note that aromaz is now using 6 transistors and getting awesome results....and Tesla apparently was using 6 vacuum tubes on one side of the AC motor and 6 on the other side.....coincidence...maybe.....but my instincts tell me otherwise...

The link re tesla car was by me :-) there's another link I didn't post, at bottom of page called 'another version' or something. Read that too. Also the link someone posted re moray book. And... Here's a link about the testicata machine also very interesting.

Paul Baumann: Testatika Generator (Methernitha Group)

@Aromaz. Don't forget that these lcw in aether supposedly self multiply when they encounter segmented surfaces. Tesla started scratching grooves in his caps. Also, he says the small wire on secondary coil of his transmitting tower was not an issue with the millions of volts, as it treated it 'like' a solid pipe of same diameter.

In G Vassilatos book, he claims tesla was auto magnifying voltage 10,000 times with each inch of single turn copper helix.

Also remember radiant event travels at right angles to current flow (when it's a dc pulse) -

And tesla magnified negative OR positive aspect of aether waves, depending on wether copper helix was placed (or was it spark gap was placed?) nearer pos or neg terminal of dynamo (high pressure dc source)

Anyway, food for thought.

@ Aromaz.

I replicated your circuit this morning after some minor problems. It appears there are a number of 2222's around, mine is KSP2222a and pins are opposite to 2n2222a.

First off.

1 light wouldnt start. I had to touch the base of the 2222 and it would run. Take my finger off the base, it switches off.

With three lights touching the base starts them and they keep going when I remove my finger. All are dim compared to my replication, but amp draw is also microscopic non polar cap in a series LC with the power coil changes the frequency. More tests to follow. No ground connection off the emitter of 2n2222 as yet.

Gentlemen, Maybe I am making a mistake? Maybe something is wrong?

I did not sleep last night; I was just pondering from one option to the other. Early this morning I fell asleep and dreamed - unfortunately I can not remember everything.

Please note: I am not a 'professional' and I do not consider these results absolute - if I did, I would not be here.

There is one thing that changed in the morning; sorry I truely forgot to mention it, probbaly due to tiredness. My earth wire is now properly gound connected to a 12mm copper steel rod hammered 250 cm deep into the raw dirt.

I think of this forum as a joint venture to help and assist each other with ideas and to experiment. It is an experimental forum? Or am I wrong?

Before I go and spend/risk some US$ 220 I thought to check something else first: I went looking for an Analog multi meter (that can read Micro-Amp) this morning and was fortunate to find one in an electronic shop. So very nervous I connected it up. Here are some photos I took - same setup as last night with 24 Vdc and new analog multi meter. For sake of interest and comparison, I used both the probe and 10A plug. At 10A plug that was the highest I could get the needle to move. You can see the lights on the background, now very well lit daylight in lab.

Today I am going to attempt a BIG thing. If it works there will be a video called 'Aromaz xxx' - if not then look forward to video 'Aroma #018' and let us go on to reach ‘Video xxx’ in near future - I hope, else all is in vain.

I am excited; I am scared for disappointment.

Try conditioning new master transistors with pulses from imhotep fan or imhotep self oscillating relay - to base, first. Then they should respond to aether waves from ignition coil and system will self oscillate.

@Aromaz - when I was charging battery with only one wire from pos of secondary of ignition coil to bat pos, battery did charge. I then tried wireless transmission of energy across air from point of alligator clip to cap connected to bat pos. Didn't charge until I put ground wire on bat neg.

My point being, you have one wire to cfl's on your vids. Try removing that wire, grounding cfl's instead. They should light up. Also try wrapping long fluro tube in alternating layers of wound copper wire - insulation - aluminum foil with holes - insulation etc. Might give auto intensifying effect.