Energetic Forum  
Facebook Twitter Google+ Pinterest LinkedIn Delicious Digg Reddit WordPress StumbleUpon Tumblr Translate Addthis Aaron Murakami YouTube 2019 ENERGY CONFERENCE - ONLY 150 118 99 71 63 SEATS AVAILABLE!

2019 Energy Science & Technology Conference
ONLY 150 118 99 71 63 SEATS AVAILABLE - LIMITED SEATING
Get your tickets now: http://energyscienceconference.com


Go Back   Energetic Forum > >
   

Renewable Energy Discussion on various alternative energy, renewable energy, & free energy technologies. Also any discussion about the environment, global warming, and other related topics are welcome here.

* NEW * BEDINI RPX BOOK & DVD SET: BEDINI RPX

Reply
 
Thread Tools
  #331  
Old 10-24-2018, 08:54 AM
evostars evostars is offline
Senior Member
 
Join Date: Aug 2016
Posts: 138
Lightbulb Radiant circuit progress, series resonance, parallel discharge

I still am working on Nelson Rocha's circuit (see post #329, 2 above).
I made a mistake and worked on the C4 L2 resonance.

But it turns out, L2 is series resonant with C5

C4 is charged by L1's back emf, when the mosfet turns off.
When the mosfet turns on again, C4 disruptive discharges parallel over L2 and C5.
This is a radiant energy event.

The floating ground (source of mosfet, it is NOT a earth ground), is connected to the separate powersupply (battery)
for the pulse generator driving the gate of the mosfet.
This is needed due to the high side switching with a N-mosfet

The mosfet needs to be low Rds, and capable of high current and high voltage.
Like the IRFP460A.
Switching on and off needs to be very fast.

L2 and L3 can step up or step down the voltage/current.
L2 is tuned for maximum current in L3, without having L3 tuned (no parallel C6 cap over L3)
For max current, L2 needs to have many turns, L3 few turns (but thicker wire).
Best results would need equal mass L2 and L3

C4 needs to have low ESR to be able to charge and discharge very fast. C4 also needs to have enough capacitance to violently discharge in to L2/C5 but needs to be small enough, to be able to get charged from L1 back emf in 1 cycle.
Best would be to parallel connect several capacitors.

Once L2 is tuned for max current in L3,
L3 is tuned to resonate, giving maximum voltage and current (in phase producing usable power in L3)

Parts are ordered and in the email, When I get decent results, I will make a video again, and explain it in more detail.
__________________
 

Last edited by evostars; 10-24-2018 at 09:05 AM.
Reply With Quote

Download SOLAR SECRETS by Peter Lindemann
Free - Get it now: Solar Secrets

  #332  
Old 10-27-2018, 02:14 PM
evostars evostars is offline
Senior Member
 
Join Date: Aug 2016
Posts: 138
positive discharge spike in L2

As I still dont understand fully how this works. I keep learning from my mistakes... So this info above might be wrong... Ill have to make it work first before I share this kind of information.
Still doesnt work... but learning along the way.

Made a pulse generator circuit to drive the mosfet (irfp460a). its powered by a separate battery and connected to the "earth" (NOT an earth ground).
This is to properly open and close the mosfet whule high side switching L1, generating back emf, into C2 C3 and C4.

Somehow, this circuit creates a positive discharge in the resonant L2 at max voltage. How to do this is the big question right now.

If you know ... please share. All tips and ideas are welcome

__________________
 
Reply With Quote
  #333  
Old 11-16-2018, 04:57 PM
evostars evostars is offline
Senior Member
 
Join Date: Aug 2016
Posts: 138
high side switching a coil

My new video about switching

https://youtu.be/Asa2RuubKWM
__________________
 
Reply With Quote
  #334  
Old 11-22-2018, 06:57 PM
evostars evostars is offline
Senior Member
 
Join Date: Aug 2016
Posts: 138
Lightbulb longitudinal current video

new video about longitudinal current wil premiere in one hour

https://youtu.be/MF1lVtAgzVM
__________________
 
Reply With Quote
  #335  
Old 12-06-2018, 05:22 PM
evostars evostars is offline
Senior Member
 
Join Date: Aug 2016
Posts: 138
Lightbulb impulsed bifilar coil, from both ends

I found out, the best way to impulse a bifilar coil, is to impulse it from both ends, one side positive impulse other side negative impulse, but simultaneously.
Nelson rocha's latest shared circuit does this.

It not only does that, but in the same coil that is impulsed, is also series resonance creating high currents.

the impulsed series resonant coil, is a primary.
The secondary, is inductive coupled, so sees the high currents. But is also in the radiant field induced by the impulses.

Without the current, resonance can easily be tuned into the secondary, as you will be able to see what you are doing on s scope. But the high current, prevents this... It seems to be tuned differently...

So with the current in the secondary, your tuning blind... adding capacitance until it resonates with the impulses of the primary.

When tuned, this could deliver voltage in a high current coil. in phase.
So far only theory...
only need to tune...
__________________
 
Reply With Quote
  #336  
Old 04-14-2019, 05:58 PM
evostars evostars is offline
Senior Member
 
Join Date: Aug 2016
Posts: 138
Thumbs up new video

New video is a warm up for the next video.

It gives extra information on Tesl's bifilar coil, and
how to switch on the high side using a IRFP460 n-mosfet.

https://youtu.be/Y0TJ84Rbx6Q
__________________
 
Reply With Quote
  #337  
Old 04-19-2019, 01:49 PM
evostars evostars is offline
Senior Member
 
Join Date: Aug 2016
Posts: 138
Lightbulb Radiant power, by SS hairpin circuit

I made an advanced solid state hairpin circuit producing radiant power.

It is based on a high side switched coil (L1) producing a negative back EMF impulse.
This impulse is injected into a series resonant bifilar pancake coil (L2).
The BEMF impulse, replaces the sparkgap.

This L2 coil also has a positive DC offset, charged by the back EMF.
The L2 coil equals the stout bars in the hairpin circuit.

L2 is loose coupled (4,5cm) to L3 (bigger bifilar pancake coil) that is parallel resonant. So both L2 and L3 resonate on the same frequency. L2 is series resonant (low impedance, so impulse can pass to positive of power suppy, giving the L2 a kick) and L3 is parallel resonant (high impedance).

L3 is parallel loaded with a 28W 230V light bulb, that lights up brightly.
The current and voltage of L3 are in phase. This is rather unique, as it is 4,5 cm distanced from the series resonant L2 (current and voltage 90 degrees out of phase). Radiant power is produced.

Here is the link to the video explaining it all. All info that is needed for replication is included.
https://youtu.be/1Flj1i0zQ-8

Here is the link to the schematic:
https://imgur.com/a/sh1JOwE
__________________
 
Reply With Quote
Reply

Tags
coil, field, bifilar, magnetic, video, talk, resonant, frequency, nature, special, series, findings, energy, current, radiant, rise, videos, pulsed, voltage, dielectric, share, interesting, states, things, added

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



Please consider supporting Energetic Forum with a voluntary monthly subscription.

Choose your voluntary subscription

For one-time donations, please use the below button.


All times are GMT. The time now is 04:07 AM.


Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
Search Engine Optimisation provided by DragonByte SEO v1.4.0 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
Shoutbox provided by vBShout v6.2.8 (Lite) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
2007-2015 Copyright - Energetic Forum - All Rights Reserved

Bedini RPX Sideband Generator

Tesla Chargers