Energetic Forum  
Facebook Twitter Google+ Pinterest LinkedIn Delicious Digg Reddit WordPress StumbleUpon Tumblr Translate Addthis Aaron Murakami YouTube 2018 ENERGY CONFERENCE - ALL SEATS SOLD OUT!

2018 Energy Science & Technology Conference
Sponsored by Teslacoin Foundation

Teslacoin Foundation

http://tesla-coin.com


Go Back   Energetic Forum > >
   

Renewable Energy Discussion on various alternative energy, renewable energy, & free energy technologies. Also any discussion about the environment, global warming, and other related topics are welcome here.

* NEW * BEDINI RPX BOOK & DVD SET: BEDINI RPX

Reply
 
Thread Tools
  #2881  
Old 11-09-2014, 11:35 PM
sampojo's Avatar
sampojo sampojo is offline
Senior Member
 
Join Date: Nov 2010
Posts: 429
Monster driver board death in AMC

Things looking up, only one mosfet looks bad. Had to isolate the mosfets to find out if only one was bad, so I had a 50-50 chance and even this squirrel found a nut, first try got the right one. As soon as I took the bad board out, of the shared ground, the other one started working, too. And I am using a new soldering bit and now I have plenty of power to work on the 12ga wire on my 100w iron. Planning ways to squeeze in 4 mosfets per board, as Dana suggested
__________________
Up, Up and Away
Reply With Quote

Download SOLAR SECRETS by Peter Lindemann
Free - Get it now: Solar Secrets

  #2882  
Old 11-30-2014, 05:52 PM
Gringo11 Gringo11 is offline
Junior Member
 
Join Date: Nov 2014
Posts: 3
Hold Tight - new MOSFET on the way

Hello All,
This might be just what we may need to deal with temperature and losses on MOSFET and allow faster switching. New SiC MOSFET in the making.

Please see link below:

Scottish facility develops SiC mosfets for electric car maker | Electronics Weekly

Cheers - Gringo
__________________
 
Reply With Quote
  #2883  
Old 12-02-2014, 04:42 AM
sampojo's Avatar
sampojo sampojo is offline
Senior Member
 
Join Date: Nov 2010
Posts: 429
woo-hooo great results with AMC and unipolar motor

Very preliminary. Got my AMC fired up finally. I had a gremlin running around the mosfets on one board, seemed to have a bad one after I converted my boards to quad-mosfet construction. It was on the board that I used Kog's method of going to the terminal from the heat sink. This has a great trouble shooting advantage as you can simply disconnect each mosfet and isolate it without having to unsolder!!! Slowly started disconnecting the Mosfets, seemed to detect a fault once but then could not. When first connected this channel would run the motor even when the Arduino was not pulsing. slapped things backed together taking some shortcuts to test the board, had to assume it was gonna work, and it did!!

So here are my results. When pulsing, probably around 1KC at full on, my GM window double rotor dual stator unipolar winding did about 3450 rpm. I need a more sensitve ammeter, cause it was like it wasn't even flinching. when run as direct feed it takes at least 1.0+ amps. I ran it direct feed both brush sets, and got about 100rpm more. Close enough to compare for now! So it didn't even want to register 1 tick (1/2 amp) on the AMC and direct feed I know it takes about an amp.

Standby as I will measure this up, down and sideways in the next few days.

EDIT bad idea trying to make any deductions from a meter on the low end out of range for the job... It seems to stick sometimes I see today. found the bad mosfet from originals on the board now also. failed at a 50ohm short, not completely shorted yet...
__________________
Up, Up and Away

Last edited by sampojo; 12-03-2014 at 01:11 AM.
Reply With Quote
  #2884  
Old 12-23-2014, 08:53 PM
Back-halo Back-halo is offline
Junior Member
 
Join Date: Apr 2014
Posts: 3
Question recommendation for my1016

Hello, I've been looking at something for my1016 but not cleared me, recommend me something to make it free energy or radiant energy that is easy to do for someone with no knowledge of electronics like me, if there is a circuit that can do that no amount taking oscillator or more complicated things, I want to to put it on my scooter and to travel many kilometers or go to school. any solution that can give me? do not laugh.
__________________
 
Reply With Quote
  #2885  
Old 12-29-2014, 01:20 AM
sampojo's Avatar
sampojo sampojo is offline
Senior Member
 
Join Date: Nov 2010
Posts: 429
AMC update: Testing Power gains of AMC the goal

My quad mosfet design runs super cool, no detectable heating with the motor on a 12v power supply. My main goal in this is to achieve the radiant energy gains promised by synchronous pulsing delivered by using the arduino with JS Monster Drivers. So the question is how could these energy gains be verified. I have been comparing a conventional pulse width modulator motor driver to my AMC and have some preliminary results.

The test is simple:
  1. Run the AMC at max power (using 12v power suppy)
  2. Record total amperes
  3. Hook up the motor to a conventional PWM
  4. Run at the same RPM
  5. Record total amperes
RESULTS:My unipolar GM window motor draws about 1.1A on the conventional PWM and about .08A less on the AMC.

I do not get a big swing in amperage, it jumps up near an amp just to rotate, and peaking at the above values at the AMC max. The PWM max actually delivers more RPM. And straight from the power supply gets the most RPM. Since the voltage is pulsed, I plan to look for an average voltage value for the duty cycle potentiometer position.

I am concerned that I am measuring such a small amount of difference. I will work towards a video. As for now, I have fried my PWM and a new one is on order.
__________________
Up, Up and Away
Reply With Quote
  #2886  
Old 02-14-2015, 10:57 PM
TonyD TonyD is offline
Junior Member
 
Join Date: Dec 2012
Posts: 2
Post Hello!

Hello all,

I know I am a bit late to the party, but I was hoping someone would be able to post an image of the original circuit that I could start working from. Preferably, the one referenced on post #126 with the polarities corrected. I have read a lot of the posts and the images seem to be missing from the start of the thread, so I would appreciate if someone would be able to help me out.

Thanks,

TonyD
__________________
 
Reply With Quote
  #2887  
Old 02-15-2015, 02:20 PM
Ufopolitics's Avatar
Ufopolitics Ufopolitics is offline
Platinum Member
 
Join Date: Feb 2012
Location: US, Florida
Posts: 4,878
Hello Tony and welcome

Quote:
Originally Posted by TonyD View Post
Hello all,

I know I am a bit late to the party, but I was hoping someone would be able to post an image of the original circuit that I could start working from. Preferably, the one referenced on post #126 with the polarities corrected. I have read a lot of the posts and the images seem to be missing from the start of the thread, so I would appreciate if someone would be able to help me out.

Thanks,

TonyD
Hello Tony,

Ok, if you look at the post I have made after, or #127 here

You could see the simplest controller built with the 555 timer, and schematics are here
And here from my albums with more FET's:

[IMG][/IMG]

I made a more complex circuit by adding a voltage regulator (LM317) to use it with higher voltage than 12V (36V) , plus more MOSFET's (they are all N-Channels) connected in parallel to stand higher pulsing amps, as shown below:

[IMG][/IMG]

And below is a detailed zoomed view of the LM317 Voltage regulator correct circuit and components.

[IMG][/IMG]

Cheers and welcome again!


Ufopolitics
__________________
 

Last edited by Ufopolitics; 02-15-2015 at 02:27 PM.
Reply With Quote
  #2888  
Old 02-16-2015, 06:20 PM
TonyD TonyD is offline
Junior Member
 
Join Date: Dec 2012
Posts: 2
Much appreciated

Quote:
Originally Posted by Ufopolitics View Post
Hello Tony,

Ok, if you look at the post I have made after, or #127 here

You could see the simplest controller built with the 555 timer, and schematics are here
And here from my albums with more FET's:

[IMG][/IMG]

I made a more complex circuit by adding a voltage regulator (LM317) to use it with higher voltage than 12V (36V) , plus more MOSFET's (they are all N-Channels) connected in parallel to stand higher pulsing amps, as shown below:

[IMG][/IMG]

And below is a detailed zoomed view of the LM317 Voltage regulator correct circuit and components.

[IMG][/IMG]

Cheers and welcome again!


Ufopolitics

Hello Ufopolitics,

Thank you very much for taking the time to supply the above links/images. I will set about my experiments and feedback on my successes or otherwise...

Thanks again,
TonyD
__________________
 
Reply With Quote
  #2889  
Old 03-03-2015, 06:56 PM
sampojo's Avatar
sampojo sampojo is offline
Senior Member
 
Join Date: Nov 2010
Posts: 429
conventional PWM performance vs Arduino/Monster driver

I had run a quick comparison on my GM window asym motor series I have built and on the ragged end of detection I thought I saw a 7% improvement in performance (dual stator). I haven't been able to conduct any more significant testing because my motor seems to keep burning up my conventional PWM controllers. This kind of reminds me of John Stone saying many time how the monster driver boards were designed to withstand all the bemf effects of these motors while conventional designs would be insufficient. So true it seems... As for my neon radiant energy detection circuits I have built in on my AMC I can verify they work, as when running it on my asym motors, I can see them flicker dully when I turn down the lights I think I will have to build a new program to have my AMC function as a conventional PWM in order to nail down the performance of pulsing brushsets synchronously vs conventionally. The effects are supposed to be stronger on a quad stator asym motor and that is still in the works, as my first design ran way too hot.
__________________
Up, Up and Away
Reply With Quote
  #2890  
Old 03-03-2015, 09:14 PM
Midaztouch's Avatar
Midaztouch Midaztouch is offline
Silver Member
 
Join Date: Feb 2013
Location: Japan for 2yrs
Posts: 546
Quote:
Originally Posted by sampojo View Post
I had run a quick comparison on my GM window asym motor series I have built and on the ragged end of detection I thought I saw a 7% improvement in performance (dual stator). I haven't been able to conduct any more significant testing because my motor seems to keep burning up my conventional PWM controllers. This kind of reminds me of John Stone saying many time how the monster driver boards were designed to withstand all the bemf effects of these motors while conventional designs would be insufficient. So true it seems... As for my neon radiant energy detection circuits I have built in on my AMC I can verify they work, as when running it on my asym motors, I can see them flicker dully when I turn down the lights I think I will have to build a new program to have my AMC function as a conventional PWM in order to nail down the performance of pulsing brushsets synchronously vs conventionally. The effects are supposed to be stronger on a quad stator asym motor and that is still in the works, as my first design ran way too hot.
Sampojo

You are still banging away at the JS Monster and AMCs.
synchronously vs conventionally... Off hand, what differences could there be? Can you post a vid or pic of your conventional controller?

You had heating in the past then improvements. Are the motors North/South wind or all north groups or pairs? Which design did you use for each tests?

Keep it clean and Green
Midaz

Keep it Clean and Green
__________________
 

Last edited by Midaztouch; 03-03-2015 at 10:46 PM.
Reply With Quote
  #2891  
Old 03-16-2015, 02:21 AM
sampojo's Avatar
sampojo sampojo is offline
Senior Member
 
Join Date: Nov 2010
Posts: 429
AMC/MS5.1/ vs conventional PWM

Quote:
Originally Posted by Midaztouch View Post
Sampojo

You are still banging away at the JS Monster and AMCs.
synchronously vs conventionally... Off hand, what differences could there be? Can you post a vid or pic of your conventional controller?

You had heating in the past then improvements. Are the motors North/South wind or all north groups or pairs? Which design did you use for each tests?

Keep it clean and Green
Midaz

Keep it Clean and Green
Hey Midaz,

The deal is if you pulse each brush set in a synchronous order, its supposed to release more Radiant Energy, as opposed to the way a conventional PWM would pulse each brush set under power at the same time, or a battery in direct feed. I wound a unipolar quad stator of mine recently but was off on the resistance and haven't gotten around to rewind it. I am trying to operate on motors in the 5A and under range. I have burnt up a couple cheap motor controllers so I am thinking things John Stone had posted about all the RE running around needs a lot of heavy duty components. I plan to make a program running the AMC as a conventional PWM to test things out. Still need to build some more monster driver boards. I was out of work for a few months for an operation and during recover hacked away at this stuff. Not so much time any more back on the job. Working on the unipolar designs. Got a Quad Pentagon Bent Y 10 pole, which is a N-S Winding to compare to, but it also runs hot, with too low a coil resistance, so if I build a good unipolar motor, they may be tough to compare since the wire gauge ratings will necessarily be different. I am leaning toward multifilar windings too.
__________________
Up, Up and Away

Last edited by sampojo; 03-16-2015 at 02:46 AM.
Reply With Quote
  #2892  
Old 03-16-2015, 06:28 AM
Midaztouch's Avatar
Midaztouch Midaztouch is offline
Silver Member
 
Join Date: Feb 2013
Location: Japan for 2yrs
Posts: 546
Quote:
Originally Posted by sampojo View Post
Hey Midaz,

The deal is if you pulse each brush set in a synchronous order, its supposed to release more Radiant Energy, as opposed to the way a conventional PWM would pulse each brush set under power at the same time, or a battery in direct feed. I wound a unipolar quad stator of mine recently but was off on the resistance and haven't gotten around to rewind it. I am trying to operate on motors in the 5A and under range. I have burnt up a couple cheap motor controllers so I am thinking things John Stone had posted about all the RE running around needs a lot of heavy duty components. I plan to make a program running the AMC as a conventional PWM to test things out. Still need to build some more monster driver boards. I was out of work for a few months for an operation and during recover hacked away at this stuff. Not so much time any more back on the job. Working on the unipolar designs. Got a Quad Pentagon Bent Y 10 pole, which is a N-S Winding to compare to, but it also runs hot, with too low a coil resistance, so if I build a good unipolar motor, they may be tough to compare since the wire gauge ratings will necessarily be different. I am leaning toward multifilar windings too.
For hot coils, are you thinking about using thicker wires with less turns or thinner with more turns?

Keep it Clean and Green
Midaz
__________________
 

Last edited by Midaztouch; 03-16-2015 at 08:03 AM.
Reply With Quote
  #2893  
Old 03-19-2015, 03:34 AM
sampojo's Avatar
sampojo sampojo is offline
Senior Member
 
Join Date: Nov 2010
Posts: 429
hot coils question

I have gotten alot of input from Prochiro on how to get them most out of a rotor. and of course Ufo has stated a coil must come in around one ohm resistance. I try to fill up the rotor to get the most out of it. Using multifilar complicates the calculation but I am getting better at it. It gives you options. My motor was hot-running bc I made the wire thicker by going to 4 strands and I went longer since the rotor wasnt filling up on my first winding at 3 strands. But I ran out of room making the coil length shorter than I should and was coming in at around .7 ohms per coil when it was fully wound. My solution here is to go back to 3 strands and go longer, targetting about 1.33 ohms per coil to allow it run continuously and get no hotter than 120 degrees on 12v. I already have a dual stator motor of this type that is wound at around 1.3 ohms per coil, and that is how it runs. That is hot to the touch and I worry about it. I have this really good wiring guide that breaks down the resistance every which way, and since I don't have good multimeters, I am going strictly by calculation. So on this wiring guide, you may find what I am using, 32ga, 6' per ohm, and 3 strands at 24' will give 1.33 ohms. Perfecto! This will go far to filling up my rotor. I probably should do prochiro's calculation, estimating the area of the inter-pole spacing and dividing by the strand area to find out how many winds it will take to fill them...

I had been watching Ufo's vid on the imperial epic run, on the MAEM thread post 3132. And I just recently noticed one temp reading was 160+ degrees at the end of the run!!! Looks like the brushes. My question is, How hot should the motors be allowed to get? My little motors above, the whole motor will get to be 120 deg+ including the magnets. So not only do you have to worry about melting something, but also about the magnets overheating and losing their magnetism. Do you have a temp gauge? How hot is the A1-MoGen getting?
__________________
Up, Up and Away

Last edited by sampojo; 03-21-2015 at 04:55 PM. Reason: additional comments on wiring
Reply With Quote
  #2894  
Old 03-22-2015, 06:49 AM
padova padova is online now
Junior Member
 
Join Date: Jan 2015
Posts: 29
I have edited this post, since I get more acquainted with this topic.

But you can see it down below

regards
__________________
 

Last edited by padova; 03-29-2015 at 08:55 AM.
Reply With Quote
  #2895  
Old 03-22-2015, 11:12 AM
Ufopolitics's Avatar
Ufopolitics Ufopolitics is offline
Platinum Member
 
Join Date: Feb 2012
Location: US, Florida
Posts: 4,878
The Critical "Audience"...(another one)

Quote:
Originally Posted by padova View Post
Hi,
I read this thred for some time. I came to the conclusion pretty quickly, I think.
This thing has nothing to do with Cold electricity, or "SHE" as some have called it.
Oh master of masters!!......please, (we beg to your 'Honor') let Us know all what Cold Electricity really is?

Quote:
You would not supposed to misleading people.
But explain what it actually is. Certainly not the Cold electric, for sure.
Why don't you, master of masters, explain to ALL of Us...naive people, what Cold Electricity, Radiant Energy is...before you keep judging...

Quote:
As what yours Intentions are. But that might have effect to reject a lot of naive, who participate in this game.
Please reed more on the subject, what cold electricity is, and how it behaves.
You are judging and criticizing is NOT CE nor RE, SO it is completely on YOUR END to speak up and demonstrate what really is.

Quote:
Unfortunately, practical applications, are not available to the public. as far as known so far.
OH!!...applications are not 'available' to "public"?!...

Quote:
Also, what efficiency of this setup is? How much energy you put in, and how much you get of of it.
Why you need so great amperages, when cold electricity can supply great power thru some tine wires,
for example.
Some have said "there is not such thing as pure cold appliancis" , I think that is description of this setup.
If some have had produced more power, or wast power, out of 36VDC, please report it,Anonymously ,thru
the network of servers, so no agency can track it.
Have YOU done ANY of all this Experiments so far?...all you did was "read"...in a language you do not "master".

Quote:
This is some kind of an unconventional approach to energy.So is P.J. Kelly put it in his book.
But anyone can see that there is some kind of reserve towards it.

regards.

ps.
I never mastered english so closely, sorry if I was grammatically incorrect.
You are not only 'grammatically' incorrect, but your paragraphs do not make sense, they do not complete the "idea" about what you are "trying" to say ...everyone who read you, must keep "guessing" what you are intending to express.

Do You really expect that by just 'reading' here (no matter how long it took you to accomplish that) grant you the right to come here and judge, criticize plus insult, calling Us all "naive", misleading people, etc,etc...?

Back up all your 'judgement calls' with real examples, cite them, bring literature that back up all you are saying...show your expertise in the fields...etc,etc...only then you will offer some 'respect' for yourself.


Use -at least- a little bit of Scientific approach with your words.



Ufopolitics
__________________
 

Last edited by Ufopolitics; 03-22-2015 at 11:15 AM.
Reply With Quote
  #2896  
Old 03-22-2015, 12:59 PM
padova padova is online now
Junior Member
 
Join Date: Jan 2015
Posts: 29
Sorry again, if I was impolite.

I have read the Theories in my language,and in english to. I'm pretty far from been one
who just teach and does nothing.
In my formal education I was learning Russian.English I just learning from time to time,
maybe it's not necessary to know it.
regards
__________________
 

Last edited by padova; 03-29-2015 at 09:56 AM.
Reply With Quote
  #2897  
Old 03-26-2015, 05:32 PM
padova padova is online now
Junior Member
 
Join Date: Jan 2015
Posts: 29
Hi UFO
I watched just recently, your thread on Asymmetric motors. It is quite impressive.
You made your point there. Congratulations.
I'll give it a try, also this configuration with the coil as well.

Best Regards
__________________
 

Last edited by padova; 03-29-2015 at 09:11 AM.
Reply With Quote
  #2898  
Old 03-26-2015, 06:06 PM
pedroxime pedroxime is offline
Member
 
Join Date: Dec 2010
Posts: 36
thanks ufo

i began some days ago to study your stuff, really between the most interesting in the internet
__________________
 
Reply With Quote
  #2899  
Old 03-26-2015, 08:12 PM
BroMikey's Avatar
BroMikey BroMikey is offline
Platinum Member
 
Join Date: Jan 2013
Posts: 5,133
Hey UFO

Been watching your thread dude. Where do all of these comedians come from, can't speak English much at all and I wonder what they are even saying. Sounds like he wants you to give up all of your investigative work for free.

What a world. All of these folks who steal and belittle will never amount to anything. Keep pushing forward because your students are breaking all of the old models.

Nothing like a free loader.

Mikey




Quote:
Originally Posted by Ufopolitics View Post
Oh master of masters!!......please, (we beg to your 'Honor') let Us know all what Cold Electricity really is?



Why don't you, master of masters, explain to ALL of Us...naive people, what Cold Electricity, Radiant Energy is...before you keep judging...



You are judging and criticizing is NOT CE nor RE, SO it is completely on YOUR END to speak up and demonstrate what really is.



OH!!...applications are not 'available' to "public"?!...



Have YOU done ANY of all this Experiments so far?...all you did was "read"...in a language you do not "master".



You are not only 'grammatically' incorrect, but your paragraphs do not make sense, they do not complete the "idea" about what you are "trying" to say ...everyone who read you, must keep "guessing" what you are intending to express.

Do You really expect that by just 'reading' here (no matter how long it took you to accomplish that) grant you the right to come here and judge, criticize plus insult, calling Us all "naive", misleading people, etc,etc...?

Back up all your 'judgement calls' with real examples, cite them, bring literature that back up all you are saying...show your expertise in the fields...etc,etc...only then you will offer some 'respect' for yourself.


Use -at least- a little bit of Scientific approach with your words.



Ufopolitics
__________________
 
Reply With Quote
  #2900  
Old 03-27-2015, 06:55 AM
padova padova is online now
Junior Member
 
Join Date: Jan 2015
Posts: 29
Hi,

BroMikey@

You're quoting UFO's replay to me. So I think I need to say something to.
But first, what this,quoted below, means. For gods sake.
Quote:
Sounds like he wants you to give up all of your investigative work for free.
My last post, I believe was quite clear.
You may Interpret it at your free will.

I think it might be a god idea to put you on Ignore

Have a nice day
__________________
 

Last edited by padova; 03-29-2015 at 09:54 AM.
Reply With Quote
  #2901  
Old 05-03-2015, 02:47 AM
nrg2171 nrg2171 is offline
Junior Member
 
Join Date: Jun 2012
Posts: 2
My first replication

Hi Ufopolitics

I tried to replicate your circuit and it seems to work but I leave it to to judge.
I will go ahead and describe the circuit and I will appreciate your time to correct me.

555 timer .
------------
after frying 15 chips I added a diode from ground to pin 3. (I just copied it from an ignition coil driver) it seems to work so far.

Mosfet
-------
I used the sp45n20a wich is 200v 20A
before puting the diode on pin 3 of 555 it get very hot.
after puting the diode it runs cool.

the coil
--------
the coil used is bifillar that i was gonna use for bedini motor. it is 20 awg and 21 awg. and iam getting some result which means you're totaly right.

i tried to charge a dead 6v 6ah battery, the circuit makes it boil within 30 mn .

I read the forum until page 15. then I found a pdf file summary of the oscillator which is good enough.

while reading your posts I marked two very important notes
1- you mentioned that you blew your bulb with only 4 volts.
2- you said you got excellent results on electrolysis with 2 spoon of salt .
it would be great if you comment more in details if you don't mind.

is it ok to use speaker wire as bifilar ?

thank you
Attached Images
File Type: jpg radient nrg on neon bulb.jpg (109.0 KB, 32 views)
__________________
 
Reply With Quote
  #2902  
Old 08-20-2015, 05:56 PM
Firebrand Firebrand is offline
Junior Member
 
Join Date: Aug 2014
Posts: 1
Hello and a comment

Hi to all, I am a newbie to this forum and electronics, however, I have been studying this circuit for some time. Thanks UFO for posting this info, you are doing a service to mankind.
A couple of points I would make
Patrick Kelly covers this circuit on his website Chapter 3 pages 180 to 189 http://www.free-energy-info.tuks.nl/Chapter3.pdf
He presents a good outline of the device.
For someone like me attempting to replicate this I'm faced with some issues one, I'm just about getting on top of the technology, I've been studying John Bedini SG & SSG Beginners, Intermediate & Advance for the past few weeks and more or less understand the circuit but of course it has to built. Anyway I'm looking at this particular thread and I'm wondering how do I get an understanding of this, there is about a months reading on it, I did attempt to read it all, but got into page 30 and found a lot of the information was off topic or written in tech speak that is to say people using technological jargon that I did not understand, so the thought occurred to me why does UFO not write a pdf on the circuit just as Peter Lindemann and Aaron Murakami have done with John Bedini's SG and sell it on this website, I would definitely buy it, just a thought.
__________________
 
Reply With Quote
  #2903  
Old 11-07-2015, 06:25 PM
lara powl lara powl is offline
Junior Member
 
Join Date: Jul 2015
Posts: 1
Hi guys,
Like TonyD I am jumping here obviously late and didn't found any link to schematics working, so I will appreciate any instructions how to build Sir John Stone's Monser Driver. I already built a replica of a smal 3 pole motor and it seems work very good.
My appreciations to all of you for your work
__________________
 
Reply With Quote
  #2904  
Old 11-11-2015, 05:30 PM
GlenWV GlenWV is offline
Member
 
Join Date: Nov 2009
Posts: 86
Schematics for build

Quote:
Originally Posted by lara powl View Post
Hi guys,
Like TonyD I am jumping here obviously late and didn't found any link to schematics working, so I will appreciate any instructions how to build Sir John Stone's Monser Driver. I already built a replica of a smal 3 pole motor and it seems work very good.
My appreciations to all of you for your work
Greetings:

Once you have John's schematics, you can build the unit on a generic board like from Radio Shack, or purchase from EBay.

I've built them this way.

Keep looking around this list and you'll find that Sampojo, I think, or Dana maybe, posted a link for professionally made boards. The cost is about $100.00 for three of them. - - I really forget, but have a link to the company on my desktop at home. There may be a 'new & improved' version.

I have two coils. One of 18 gauge wire, and the other of 14 gauge wire. Both are calling to me to start experimenting with them again.

Keep posting. You might renew the interest in these coils and the circuit.

See: My Asymmetric Electrodynamic Machines

glen
__________________
 
Reply With Quote
  #2905  
Old 12-30-2015, 08:55 PM
darediamond darediamond is offline
Member
 
Join Date: Sep 2015
Posts: 35
Radiant Energy Conversion

The Cold Electricity needs to bé converted and stored before it can bé steped down for powering the Motor itself again and again.

Thus you need to connect an High Voltage Fast Switchich Diode to the Negative terminal of the Coil. Or beter still make an high Voltage Full Wave Rectifier and Connect H.Voltage DC Capacitors to the Output leads of the Diodes.
The Capacitor will convert from Cold Electricity to Hot Electricity the incoming Back EMF and you the Simply Step-down the Voltage to a usable voltage using a transformer.

Also, though it's better, if you can't easily deal with Mosfets, use Copper Commutator. There is a way you can make it at home using Copper Pipes or PVC Pipe and Copper tape.

It is best to make a Capacitorlike Electromagnet with Multifilar Copper Wire. The benefit in this is that it improves the ability of the Coil to Absorb enormous amount of Ahir base Electric Power.


Note that to collect extremly maximum Wattage from the Ahir, your Coil must bé powered with High Voltage and swiched at high rate or Frequency. The Higher the frequency the Higher the Output Radiant Energy Amplified Back E.M.F


The free Electricity in the Ahir is Pulsing so to tap it, you must use a Pulsing Magnetic Device.
__________________
 

Last edited by darediamond; 12-30-2015 at 09:10 PM.
Reply With Quote
  #2906  
Old 01-06-2016, 10:20 PM
Back-halo Back-halo is offline
Junior Member
 
Join Date: Apr 2014
Posts: 3
can buy?

you can buy one of these finished and ready to roll? I am disabled and I need something to move away, stop laughing and launch it on the market. I would like to talk to Netica.
__________________
 
Reply With Quote
  #2907  
Old 01-06-2016, 10:23 PM
Back-halo Back-halo is offline
Junior Member
 
Join Date: Apr 2014
Posts: 3
Launch this on the market !!!!!

Launch this on the market please !!!!!
__________________
 
Reply With Quote
  #2908  
Old 01-08-2016, 09:13 PM
Ufopolitics's Avatar
Ufopolitics Ufopolitics is offline
Platinum Member
 
Join Date: Feb 2012
Location: US, Florida
Posts: 4,878
Quote:
Originally Posted by Back-halo View Post
Launch this on the market please !!!!!
Another Experiment proving the same results as Netica...



Kashif Khan Experiment

Thanks and regards Back Halo!


Ufopolitics
__________________
Principles for the Development of a Complete Mind: Study the science of art. Study the art of science. Develop your senses- especially learn how to see. Realize that everything connects to everything else.― Leonardo da Vinci

Last edited by Ufopolitics; 01-08-2016 at 09:43 PM.
Reply With Quote
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



Please consider supporting Energetic Forum with a voluntary monthly subscription.

For One-Time Donations, use admin@ this domain > energeticforum.com

Choose your voluntary subscription

All times are GMT. The time now is 04:39 PM.


Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2018, vBulletin Solutions, Inc.
Search Engine Optimisation provided by DragonByte SEO v1.4.0 (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Shoutbox provided by vBShout v6.2.8 (Lite) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
2007-2015 Copyright - Energetic Forum - All Rights Reserved

Bedini RPX Sideband Generator

Tesla Chargers