Turion
Platinum Member
Last Activity: Today, 09:53 PM
Joined: 11-06-2009
Location:
-
Open circuit means the coil is c connected to NOTHING. (Except the AC meter I put across it. And I have no converter hooked to the coils....yet. If and... -
The boys showed up today after I got back from Sacramento for my doctor appointment, and got all the cores on the coils cut back. Tested each one and...Last edited by Turion; Today, 03:21 AM.Leave a comment:
-
bi,
You know what you read in a book. Good for you. I know what I built on the bench. Better for me.
Leave a comment:
-
97 volts DC at 3.5 amps DC.
Not buying anymore meters.
I don't need to be that accurate. Either this thing does what I say it does, or it...Leave a comment:
-
Got amp gauge and volt meter mounted and hooked up so I get more accurate input measurements. Going to deal with coils now...Last edited by Turion; 01-16-2022, 09:14 PM.Leave a comment:
-
The motor I am currently using has the right size shaft. It is 124V DC. It can handle over 17 amps. It will do well above the 2800 RPM required. I'm not...Last edited by Turion; 01-16-2022, 08:52 PM.Leave a comment:
-
Alex,
I know you have worked on that, and it is more than I have done. There is a lot to learn to make that work properly, but if we can switch...Leave a comment:
-
I wanted the higher voltage lower amperage motor because the coils output high voltage, low amperage. Figuring out how to loop this will be a fun little...Last edited by Turion; 01-16-2022, 05:12 AM.Leave a comment:
-
Leave a comment:
-
That last motor looks good! Looks like shaft is long enough to actually USE it for something.
I put two coils in the machine and started...Last edited by Turion; 01-15-2022, 10:57 PM.Leave a comment:
-
Pulling 70 volts on the Variac and it is only rated for 5 amps I believe. Will have to look at that. So 2800 RPM is easily achievable with this setup....Last edited by Turion; 01-15-2022, 07:55 PM.Leave a comment:
-
I already bought a heavy amp switch designed to switch the machine between two DC power sources. Start it on the Variac with the bridge and switch over...Leave a comment:
-
My Variac will output up to 120V AC, and with a bridge I can convert to DC. What I will be interested to see is the voltage and amperage output of one...Leave a comment:
-
Wasn't sure what it would take to run this new machine, but I figured less than 400 watts, and was pretty sure it would be less than 300. I have a couple...Last edited by Turion; 01-15-2022, 02:27 AM.Leave a comment:
-
Tomorrow I will connect up a Variac with a BIG bridge rectifier to get it up to the RPM needed for neutral Lenz and can start testing some coil outputs....Leave a comment:
-
Compared to the migraines I have suffered from most of my life that are so bad they induce vomiting, this is a mosquito bite. Except for the part where...Leave a comment:
-
Home from Sacramento. Have to go back Tuesday to have them do a permanent splint. No cast. No surgery. Then two more times for x-rays to make sure it...Leave a comment:
-
No pain so far, unless I move it, which I do not. I'm sure tomorrow when they set it will make up for it. Just hope no surgery is required!Leave a comment:
-
I think my guys my come out from Sacramento on Sat to help me get the motor mounted and get the coils put in and magnets adjusted. I have some little...Leave a comment:
-
Got on similar on order. Will be here Sat.
I am experiencing a delay. Was drilling new holes for motor mount as belt was too loose. Drill bit caught...Last edited by Turion; 01-13-2022, 10:53 PM.Leave a comment:
No activity results to display
Leave a comment: