Energetic Forum  
Facebook Twitter Google+ Pinterest LinkedIn Delicious Digg Reddit WordPress StumbleUpon Tumblr Translate Addthis Aaron Murakami YouTube 2020 ENERGY CONFERENCE - PRE-REGISTER NOW!!!!

2020 Energy Science & Technology Conference

Go Back   Energetic Forum > > >

John Bedini Discussion threads relating to John Bedini. Bedini SG, Bedini SSG, Crystal Batteries, etc...


Thread Tools
Old 03-12-2009, 10:21 AM
ray stewart's Avatar
ray stewart ray stewart is offline
Join Date: Jan 2009
Posts: 37
voltage spike

i am able to get a push bike head lamp 6 volt 4 oams to burn out very quickly with this pulse of very high volts and about 1 amp if i put the globe in the place of the charge battery
Reply With Quote
Sponsored Links

Download SOLAR SECRETS by Peter Lindemann
Free - Get it now: Solar Secrets

Old 03-12-2009, 10:25 AM
ray stewart's Avatar
ray stewart ray stewart is offline
Join Date: Jan 2009
Posts: 37
welding rods

try stroking them with a strong permanent magnet and see if you can magnetise them
then do the same with transformer laminations
Reply With Quote
Old 03-12-2009, 10:51 AM
ray stewart's Avatar
ray stewart ray stewart is offline
Join Date: Jan 2009
Posts: 37
regarding timing

the read switch is only to be used to flip and flop a relay" 6pin 2 state "from onebattery to the other the timing of firing will be done from the trigger coil of each indivual coil therby getting full benifit of passing magnet pluss collaps of electrical field thats why i am not changing any thing except to where the voltage spike goes and where the drive power is coming from the read switch flip flop circuit will controle the relay which can be powered from an independant sorce so if overunity exists motor will self run while eventually over charging the batteries????????? sorry if my earler reply didnt make this clear
Reply With Quote
Old 03-15-2009, 01:53 AM
ray stewart's Avatar
ray stewart ray stewart is offline
Join Date: Jan 2009
Posts: 37
its running

i went and used the K.I.S.S principal
every thing the same as ssg motor
swapping batteries around every 1 sec
using inderpendant circuit timer driving relay 2 position 12 pin
so far no voltage change after 1 hour of running
Reply With Quote
Old 03-15-2009, 09:48 AM
ray stewart's Avatar
ray stewart ray stewart is offline
Join Date: Jan 2009
Posts: 37
still running

8 hours later
voltage in accumulator "A" no change 13.1 volts
voltage in accumulator "B" droped by 0.1 volts to 10.0 volts
I guess I need to run caps now or it could run for a very long time
Reply With Quote
Old 03-15-2009, 09:54 AM
Inquorate's Avatar
Inquorate Inquorate is offline
Gold Member
Join Date: Oct 2008
Location: Sydney, Aus
Posts: 2,106
Send a message via MSN to Inquorate Send a message via Skype™ to Inquorate

Sounding good, perhaps switching batteries / caps slower than one second to see if better / worse at self running.

Whatever caps you decide to use, fill one up and see how it's charge drops naturally over time and take that into account?

Thanks for sharing
Atoms move for free. It's all about resonance and phase. Make the circuit open and build a generator.
Reply With Quote
Old 03-16-2009, 05:03 AM
ray stewart's Avatar
ray stewart ray stewart is offline
Join Date: Jan 2009
Posts: 37
not possible

i used 33 000 micro farad caps
charged from power sorce via diode through resistor
so they were constantly trickel charged at a slower rate than what was being used/recycled
initially charged to full voltage of power sauce "then trickled"
i had things set pritty well i could watch analog volt meters slowly rise and
fall the fall always slightley greater each time
"the natural discharge time of caps was so long it is irrevelant to this expirement "
i changed the cycle time of "charge discharge" from
as fast as the relays could cope
to around 2 seckonds
still caps disapated there charge in similar rate of time
then drove wheal over speed 'external power sorce same resault
so then set coil to self ossilate same thing
the power that is available to be generated from another coil on wheal is only enough to power 2 leds even if you feed this back to caps it is never enough to self run
the earlier odd resaults i was getting was due to poor calibration of volt meters
NB coil 633 turns of .6 and 0.9mm not twisted but wound on lathe set to pitch of 1.5 mm
core made from transformer laminates available in any good old microwave
the rest of moter same as basic plans
push bike wheal mounted flat making it more diverse
this remains nothing more than a good educational experiment
Reply With Quote
Old 06-22-2009, 04:16 PM
Aaron's Avatar
Aaron Aaron is offline
Co-Founder & Moderator
Join Date: Feb 2007
Location: Washington State
Posts: 11,007
self running oscillator

Originally Posted by Aaron View Post
This thread is for any Bedini SG circuits that are modified to self run....or at least attempts to self run.
My old youtube link in post #2 here is no longer valid.

Here is the updated link:
YouTube - Self Running Bedini Oscillator
of a self powered oscillator
Aaron Murakami

Reply With Quote
Old 01-03-2010, 10:15 PM
bedinimotor bedinimotor is offline
Junior Member
Join Date: Nov 2009
Posts: 3
multiple coil bedini

does anyone know how to hook up multiple coils on the bedini ssg? I hooked up a second coil last nite with the same circuit as the first and I think it blew my transistors after about 10 minutes of running. the transistors were 2n3055s. also should I have not used the trigger on the second cicuit? If not, what will I exclude from the cicuit? Thanks
Reply With Quote
Old 01-04-2010, 10:57 AM
John_K John_K is offline
Silver Member
Join Date: Jul 2008
Posts: 550
Hi Vissie,

Nice to see you on this thread, but isn't it for Bedini self-runners?

Anyhoo, I've messed around a lot with them. I did get one to run for an ectended period of time a couple of years back, but my commutation was crap. It was the same circuit Jetijs post on page 1.

Golden rules for back-popping batteries:

1. The timing must be perfect to get the HV spike from the generator coil.
2. The spike must be sent to a capacitor to convert the negative energy to positive.
3. The cap must be dumped when the SSG is off, right off.

I'll subscribe to this thread to see how it goes. I may return to another self-runner soon, I just came up with a couple of ideas I want to try. Gotta do something else besides Tesla Switches.

John K.
Reply With Quote
Old 09-12-2018, 09:36 PM
Kraaah Kraaah is offline
Junior Member
Join Date: May 2018
Posts: 1
negative lead output batty back to positive of run battery?

has anyone the normal sg cirquit in selfosscilation the output trough a voltage doubler (2x220vdc 680uf and 2 Big diodes) into a big cap(bank) and this goes to the secondary battery pulsed by a selfossilating relay style capdump12v(the one on youtube , it was someone from this forum) but when i connect the - from the 2e batty and connect it to to run battery'S + intresting things happend.. sorry for short and crappy discription,my phone is semi smashed.. i only found out today but for what ive seen the runbatt went down much slower AND chargebatt charged quicker.. am i harming the battrries this way? Since the + of the runbatt is the - of the charge batt it doesnt short so i think ?
Reply With Quote
Sponsored Links

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Please consider supporting Energetic Forum with a voluntary monthly subscription.

Choose your voluntary subscription

For one-time donations, please use the below button.

All times are GMT. The time now is 03:27 AM.

Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
Search Engine Optimisation provided by DragonByte SEO v1.4.0 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
Shoutbox provided by vBShout v6.2.8 (Lite) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
2007-2015 Copyright - Energetic Forum - All Rights Reserved

Bedini RPX Sideband Generator

Tesla Chargers