Energetic Forum  
Facebook Twitter Google+ Pinterest LinkedIn Delicious Digg Reddit WordPress StumbleUpon Tumblr Translate Addthis Aaron Murakami YouTube 2020 ENERGY CONFERENCE - PRE-REGISTER NOW!!!!

2020 Energy Science & Technology Conference
PRE-REGISTER NOW!!!
http://energyscienceconference.com


Go Back   Energetic Forum > > >
   

John Bedini Discussion threads relating to John Bedini. Bedini SG, Bedini SSG, Crystal Batteries, etc...

* NEW * BEDINI RPX BOOK & DVD SET: BEDINI RPX

Reply
 
Thread Tools
  #1  
Old 03-27-2013, 12:54 AM
Aliman Aliman is offline
Junior Member
 
Join Date: Feb 2013
Posts: 7
My First attempt at SSG

Hello everyone, it is great to be here with like minded folk. This is my first real attempt at the Bedini SSG Monopole Mechanical Oscillator Energizer.
A short summary, at first I only had Neo Magnets 19mm x 6mm disks x4, now I am using Ceramic magnets slightly bigger than the Neoís. Now I understand what Mr. Bedini was saying, when he said not to use Neo Magnets because they saturate the core causing the circuit to use more current to repel the rotor magnet, when I switched to ceramics I noticed a current drop. Please correct me if Iím wrong, Iím not a EE just an Licensed Automotive Service Tech. with a passion for electronics.
My setup is as follows; Iím using a wooden base made out of 1/2Ē Plywood, with 5/8thsĒ side braces.The Rotor is made from a salvaged Plastic wheel from an old baby stroller. I cut out the center of the wheel and spliced in place a center hub made from Two recording Drums from some scrap VCRís I had kicking around. The Drumís have have 2 Very low friction bearings in each drum, and I have carefully aligned and Epoxied both halves together to form one extremely low friction bearing hub now containing 4 bearing for added durability. The rotor is 190 mm in diameter and the magnets Iím using Eight 25.4 mm x 8 mm disk ceramicís. The coils are made as per Mr. Bediniís coil winding instructions, just added a few extra turns for a total of 1000 turns bifilar wound #23 and #26 gauge. The other passive components are the same as Mr Bediniís instructions except for the transistor, Iím using a BD911 which is actually better and what I had on hand  Iím currently not using the Neon bulb , and Iím not blowing up any transistors, even when I accidently turn on the Energizer without the charging battery connected. But I did see a 90V spike. I recently added a slave coil with the extra components needed. Early results a very promising ! The energizer spins up to roughly 900 to 1000 RPM. The way that I calculated the RPM, (please if anyone knows that my calculation method is wrong PLEASE Tell me! ) I measured the Frequency at the Trigger coil output to Variable resistor with a Multimeter. I then divided that frequency by my total number of magnets which is 8 in my case, then multiply the total by 60 giving me the final RPM. Does this sound correct ?
The current draw on the Primary battery is 200 mA and the measurable current to the charging battery is 55 mA . I still have to perform the COP Testing on the charging battery.
I am interested in building the Cap Pulsar circuit designed by Mr. Bedini .
Very exciting
Attached Images
File Type: jpg DSCF1573.JPG (53.0 KB, 26 views)
File Type: jpg DSCF1574.JPG (60.2 KB, 20 views)
File Type: jpg DSCF1575.JPG (69.1 KB, 17 views)
__________________
 
Reply With Quote
Sponsored Links

Download SOLAR SECRETS by Peter Lindemann
Free - Get it now: Solar Secrets

  #2  
Old 03-27-2013, 05:31 AM
Aaron's Avatar
Aaron Aaron is offline
Co-Founder & Moderator
 
Join Date: Feb 2007
Location: Washington State
Posts: 11,028
Bedini SSG

Congratulations Aliman for diving in and just doing it!

With that many turns and that size wire, you may not have problems if you don't have a neon. It is when you're using 18 awg power windings and you have lots of them that the transistors can pop like popcorn from pressure explosions if you don't have neons.
__________________
Sincerely,
Aaron Murakami

Reply With Quote
  #3  
Old 03-27-2013, 02:33 PM
Aliman Aliman is offline
Junior Member
 
Join Date: Feb 2013
Posts: 7
Thank you for the info. My next setup I plan on using 18 AWG for the power wire , then should my trigger wire be 21 AWG ?

In my first post I stated a method I used to calculate the rotor RPM, was that method correct ?
__________________
 
Reply With Quote
  #4  
Old 03-28-2013, 06:36 PM
Aliman Aliman is offline
Junior Member
 
Join Date: Feb 2013
Posts: 7
Hi Aaron, thanks for your help , I have a question.

If I build a trifilar cap pulser energizer, must the slave coils be the same gauge as the power wires in the Master coil

Thanks in advance
__________________
 
Reply With Quote
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



Please consider supporting Energetic Forum with a voluntary monthly subscription.

Choose your voluntary subscription

For one-time donations, please use the below button.


All times are GMT. The time now is 05:06 PM.


Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
Search Engine Optimisation provided by DragonByte SEO v1.4.0 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
Shoutbox provided by vBShout v6.2.8 (Lite) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
2007-2015 Copyright - Energetic Forum - All Rights Reserved

Bedini RPX Sideband Generator

Tesla Chargers