Announcement

Collapse
No announcement yet.

Modded Bedini, big voltage, no current

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • robt570
    replied
    Thanks for the input guys. Will see how the thing works re charging for a few days. Will keep you posted. Rob

    Leave a comment:


  • mikrovolt
    replied
    3 filaments of .67mm or 24 awg I don't know? but I don't think it's overkill

    Right now Steven Jones group are trying to help us measure
    the output of the JT. This may help to measure
    radiant output so we might have better understanding
    with these waveforms.

    Ashworth / Stiffler is measuring heat, really looking forward
    to his upcoming video, what the doctor is up to.

    Others have been charging batteries and just know about how long it takes after the
    conditioning period.

    The radiant charge is important technology. Thankyou for your efforts,
    this is my feedback just an observation.

    .67 mm = 24 guage AWG

    John's website has MJ21194 HV transistor

    36 watts + no heat = 300V * .120mA

    comparing to conventional charger approximation
    36 watts = 12 * 3 amps - minus heat (equivalent current)
    3 amps @ 12V (is not "no current").

    I wonder if using all three trifilar for more output and adding another
    for wire for trigger check with blackchisel and those guys on
    (Bedini solid state oscillators) they really got nice units working also.

    maybe you got a good combination and just the nature of this electricity
    seems mild. (no current) if I am understanding your observation.
    Last edited by mikrovolt; 06-20-2011, 03:43 AM.

    Leave a comment:


  • Neight
    replied
    I thought this was pretty normal for most of the bedini style tech.
    lots of available voltage for charging, but minimal current on output. it's part of the efficiency of how they work. i could be wrong on this, as I am still learning, but it sounds to me like you are working just fine. as long as you are getting good charging on the output, it sounds like you have done your job well

    from the way i understand all of this (and that understanding is limited ), that is the reason why you can't "close the loop" on this kind of device, not enough current to run the input, even with the massive voltage available. it might assist with efficiency on the input, but won't self run.

    again, I might be wrong, but it sounds like you have a perfectly working device on your hands

    N8

    Leave a comment:


  • robt570
    replied
    It's a tri-filar, twisted together before coiling. .67mm copper. 50mt per length, wound onto an old fishing spool. (40mm core, 75mm dia.) I measured 2.7 ohms per coil. It stays cool, no heat generated at all. I guess the no current bit does that. I'm using an MJE3009 for the NPN and an 856 for the diode. I only have 3 watt resistors for the VR and base, but they get a little too hot for my liking... Rob

    Leave a comment:


  • mikrovolt
    replied
    The pulse looks really nice.
    can you describe the coil ?

    Leave a comment:


  • robt570
    started a topic Modded Bedini, big voltage, no current

    Modded Bedini, big voltage, no current

    Hi, been experimenting with some mods to a basic bedini solid-state and would welcome some input. I can wind up the voltage (with 12.5v input) to well over 500v P-P going out to the chg battery.(12v 270cca). My problem is, there is virtually no amperage going into the charge batt.. Is that an issue? At 12.5v/750mA in, I get 300+v out, but only at 100-120mA! I have wound output voltage up to over 500v p-p, but still not much current. Hopefully have attached some scope pics.
    Attached Files
Working...
X