Announcement

Collapse
No announcement yet.

Bedini solid state oscillator and Tesla switch combination

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • mbrownn
    replied
    This is the best circuit I have ever used to date.

    My setup has two 12v4ah lead acid batteries in series as the supply, two in parallel on the return and two on the output. I use a 5 inch fan wired Bedini style as the oscillator and it really works.

    If you can match your components so you are working at a C20 rate this thing is fantastic. I have been running it for months now, just swapping the batteries round.

    We need to promote this thread

    Leave a comment:


  • slayer007
    replied
    I have tried the Tesla switch awhile ago with the exciter circuit I have been working on.
    And it works very good with the exciter.
    Every 24 hours I would switch the batteries around.I had it running for 5 days this way.And it still could have went a lot longer.

    YouTube - continuous run and charge 3

    Leave a comment:


  • thedude
    replied
    my 2 cents

    Hi Jetijs and everyone.

    Thanks again for letting me share.

    For now i built the circuit and have been testing it and made a video to illustrate my setup so far.

    I've subbed the 20k ohm resistor for an 18 and have a 10k pot in place at the 4k ohm resistor, however the circuit runs in a very similar fashion i would say. Also have mjl21194 in place of a 2N3055.

    I will be running some more trials with this set up. So I don't really have any conclusions at the moment. I'm a little concerned with the sharp drop that i'm witnessing on the series (24volt pair at top in Jetijs's schematic), even though what i'm seeing consistently is a over all increase in the voltage after rest and especially after 5 hour period of that same 24 volt pair. Its concerning to see the voltage drop below 24 volts at all! But the recovery is significant and increasing, so i will keep testing at the same base resistance as i was previously and do more half hour on and half hour rest cycles with these batts to see if there is a pattern.

    I do see that with the right base resistance, even with an ignition coil firing a CFL bulb, that there is still enough radiant current in BEMF to cause my 125volt neon to light. Need to collect that current. ;P

    will be back soon.
    Last edited by thedude; 02-10-2011, 07:19 PM.

    Leave a comment:


  • mbrownn
    replied
    Itís a little too early to say as yet but what seams to be happening is the two source batteries go down around 50% and at the same time the return battery goes up 90+%. The battery on the output also goes up 90+%. This is using four batteries in total.

    If these figures prove to be the case, when we add the mechanical output from an SSG or SG we should be able to exceed a COP of 2

    I have to condition some batteries so this may take a week or two before I can make measurements as it is a 48hour cycle time

    By the way Jetijs I have been reading all your work and I am very impressed

    We are not worthy

    Leave a comment:


  • Jetijs
    replied
    LOL, you're welcome!

    Leave a comment:


  • thedude
    replied
    got many oscillators and will try to test this.

    Thanks Jetijs for this idea. I'll be back! (doing best schwarzenegger impression)

    Leave a comment:


  • mbrownn
    replied
    update

    The old 12Ah battery was found to have weak acid so will nead an acid change

    Leave a comment:


  • mbrownn
    replied
    To see my circuit go to http://www.falstad.com/circuit/

    Copy the text below and paste it into the applet

    The large caps represent batteries of equal capacity; the small cap is only there so that the applet will run.

    So, I have two batteries in series for the source, one on the return and one charged Bedini style.

    In the above simulator it appears close to 100% efficient.

    I only have 2 new batteries of the same capacity 10Ah, plus one old one measured at 8 Ah (it should be 10), and one as yet unknown as it is not fully recovered but marked as 12. ok, thatís not a good start but after one run on my Bedini SSG the results are interesting

    The two new batteries were used as the source measuring 12,65 and 12,7 at the start and have fallen to 12.11 and 12,2.
    The old 8/10Ah was on the Bedini charge and has risen from 12.2 to 13.72
    The unknown 12Ah started at 11.6 and has risen to 14.17

    Ok, that proves nothing except that the unknown 12Ah that would not charge normally has taken a charge and that the system works. I will have to buy two more batteries and run a more useful test

    $ 13 5.0E-6 0.05580351457700471 40 5.0 32
    T 304 144 336 160 0 0.04 1.0 0.12497614924693978 9.800304406790682 0.999
    t 272 256 336 256 0 1 -26.17318626956893 -0.7539139730316791 100.0
    w 336 176 336 240 0
    w 336 144 432 144 0
    w 432 352 336 352 0
    d 336 176 384 176 1 0.805904783
    w 336 304 336 272 0
    c 432 256 432 304 0 1.0 12.571106655748208
    w 432 256 384 256 0
    w 304 176 208 176 0
    w 208 176 208 304 0
    w 208 304 272 304 0
    w 272 304 336 304 0
    w 304 144 272 144 0
    r 272 144 272 256 0 100.0
    c 336 240 336 272 0 4.78E-6 25.41927229653725
    c 432 304 432 352 0 1.0 12.422514368565189
    c 336 304 336 352 0 1.0 12.83917466243457
    c 384 176 384 224 0 1.0 12.401835860813282
    w 432 144 432 256 0
    w 384 224 384 256 0
    w 272 304 256 288 0
    d 256 288 256 272 1 0.805904783
    w 256 272 272 256 0
    o 7 64 0 35 20.0 12.8 0 -1
    o 7 64 1 291 160.0 9.765625E-5 0 -1
    o 16 64 0 35 20.0 12.8 1 -1
    o 16 64 1 291 160.0 9.765625E-5 1 -1
    o 17 64 0 35 20.0 12.8 2 -1
    o 17 64 1 291 160.0 9.765625E-5 2 -1
    o 18 64 0 35 20.0 25.6 3 -1
    o 18 64 1 291 261.87124863169134 9.765625000000001E-155 3 -1

    Leave a comment:


  • Inquorate
    replied
    Originally posted by nilrehob View Post
    Its a variation on Inquorate's circuit:

    YouTube - tesla switch bedini hybrid

    Unfortunately most pics of his circuits are gone,
    but his vids are still online.

    /Hob

    Edit: Inquorate's explanation with the boat is quite interesting
    YouTube - kinetic energy multiplier theory
    and these circuits are both electronic versions of it.
    thanks for the plug hob most the good schematics that fell off the net i've put up on Heretical Builders - Powered by vBulletin with my threads there

    i did see a total voltage rise, but i put the spike into the charging source battery. I believe the battery's ion's inertial properties and the pulse width re the coil have a lot to do with gain. I explained the principle here

    YouTube - presentation on accessing the kinetic properties of the aether, part 4 in a series of 4

    and despite having a toddler taking heaps of my hobby time, i've been trying to continue developing the circuit..

    Universal Battery Charger - Heretical Builders

    I have build it but not done extensive testing so far. I have an automated battery swapper circuit coming that uses relays but wanted to test it first before releasing it.
    Last edited by Inquorate; 01-16-2011, 10:43 PM.

    Leave a comment:


  • nilrehob
    replied
    Its a variation on Inquorate's circuit:

    YouTube - tesla switch bedini hybrid

    Unfortunately most pics of his circuits are gone,
    but his vids are still online.

    /Hob

    Edit: Inquorate's explanation with the boat is quite interesting
    YouTube - kinetic energy multiplier theory
    and these circuits are both electronic versions of it.
    Last edited by nilrehob; 01-16-2011, 03:00 PM.

    Leave a comment:


  • nilrehob
    replied
    Let me remind you of this circuit:



    I think the second one, the modified one, is an interesting circuit,
    and a kind of merge between TS and SSG.

    /Hob

    Leave a comment:


  • Jetijs
    replied
    Originally posted by Farmhand View Post

    Umm one thing that does puzzle me though is why Jetijs has the Trifilar winding connected the way he does and not through a bridge rectifier.

    Any reason for that Jetijs ? Just curious.

    I havn't got access to that EFTV video unfortunately. I only have the Stubblefield one.

    Cheers
    Hi Farmhand,
    thank you for doing those experiments, I did not have time to do them myself
    The thing about the diode on the charging battery is that the inductive spike is essentially a DC pulse in one direction only, there is no AC component in the spike, so one diode only is sufficient. Of course you can put a rectifier there, but that does not give any extra power, so I went with one diode
    Hope this helps.

    Leave a comment:


  • Farmhand
    replied
    Hi FRC, No probs, I do admit I can be confusing, even to myself.

    The solid state Bedini oscillator that Jetijs has in his drawing can also be done as a bifilar setup, like the drawing below.

    http://public.bay.livefilestore.com/..._ss.gif?psid=1

    It's actually a quite simple and very usefull circuit, the 2k resister in the drawing I posted above can be replaced with a 1k resister and a 1K pot to adjust the frequency and power draw both at once, less resistance = less frequency = more power, and vice versa, in this case.

    I'll check out your posts.

    Cheers

    Leave a comment:


  • FRC
    replied
    Thanks for clarification

    Originally posted by Farmhand View Post
    Jetijs has not placed any extra inductors into the circuit and nor did I, the coil I refed to that is inbetween the two sets of source batteries is the oscillator power coil itself. In my opinion that qualifies it as a Tesla Switch variation, type, kind of device. But thats just my opinion and only that.
    Cheers
    Thanks for clarification. I think it is a Tesla switch arangement too. But I have a
    question, has any one else put two 12v batteries in series = 24v primary and ran it through an SSG to only a 12v charging battery. I just did this with my circuit and it seems to be working. I must tell you that my circuit is a Bedini/Imhotep radiant oscillator relay setup with an inverted Bedini circuit to convert the negative energy to positive. also combined primary output is only about 21v since one of the batteries is not fully restored yet. Its kind of a reverse Jetijs setup. The radiant oscillator has been working quite well for
    the past two months, restoring batteries I thought were long gone. If you
    have read some of my other posts you know I have not had much success
    getting an actual SSG together yet. Will keep trying.

    FRC

    Leave a comment:


  • Farmhand
    replied
    Originally posted by FRC View Post
    The trigger signal is very small that I think you are trying to recover. Take a
    look at Tesla's Impulse technology #7 Energy From the Vacuum. John B. shows
    how to get more radiant energy recovered from the circuit. I could be wrong
    about your approach.

    FRC
    Maybe a small miss-understanding I think In the original drawing that Jetijs posted, He has two sets of two source batteries, one set in series (24v) and one in parallel (12v) the two in series are powering the circuit and instead of the power going back to the negative of those two batteries and killing the Dipole, the power is going to the positive of the parallel connected source batteries which charges them at the rate of the current flow through the oscillator coil.

    It works and at the same time the actual charging battery is being charged the same as it was the normal way because the system is still running from 12 volts.

    Jetijs has not placed any extra inductors into the circuit and nor did I, the coil I refed to that is inbetween the two sets of source batteries is the oscillator power coil itself. In my opinion that qualifies it as a Tesla Switch variation, type, kind of device. But thats just my opinion and only that.

    Anyway the way I tested the setup as i outlined it above was no good because i used only one 12 volt and one 6 volt source battery and so I only had 6 volts input. Silly me, but I realised my error and why I need to do it as Jetijs has shown.

    Sorry about not being clearer in my first post. I realise I was all over the place and I probably still am. So I hope my ramblings made some sense this time.

    Umm one thing that does puzzle me though is why Jetijs has the Trifilar winding connected the way he does and not through a bridge rectifier.

    Any reason for that Jetijs ? Just curious.

    I havn't got access to that EFTV video unfortunately. I only have the Stubblefield one.

    Cheers

    Leave a comment:

Working...
X