Eric Dollard

[aminnovations]

Hi,

I have added a new post to my website:

http://www.am-innovations.com/transf...c-power-part-2

This post is part 2 in the Transference of Electric Power series and includes video experiments, measurements, and an analysis of the differences that arise in the TMT transmission experiment when powered using a spark gap generator, rather than the vacuum tube feedback oscillator used in part 1.

The experimental work is intended to investigate and demonstrate aspects of the following:

1. Tuning measurements using a vector network analyser to measure Z₁₁, the small signal ac input impedance for the experimental system, from the perspective of the spark gap generator.

2. Tuning indifference when powering a load either in the single wire transmission line or at the output of the receiver.

3. Reduced power available in the single wire transmission line.

4. Reduced power available in the receiver load.

5. Tesla radiant energy and matter phenomena.

6. Transference of electric power between the transmitter and receiver in the near field.

Best wishes,
Adrian

[David G Dawson]

Hello All,
Every time I do something here in the new format, I get an invalid URL message and that included the 'Sign In'.

Hate to say this but I detect something missing in all of the good work presented by AMInnovations in that there is no plasma being used across the spark gap and I thought that was what Tesla saw as a paramount consideration.
This is what Chernetsky with his 'Self-Generating Discharge' and my 'Impulse Discharge' also does, that once you eliminate the spark and a plasma takes over, your input power drops by 2/3rd but the capacitors continue to store the energy.
This in hindsight could also be done with a variable sheet many plate capacitor at high voltage where the plasma traffic could be increased dramatically and isn't this similar to the Chris Carson device.
This is where a 'hard' spark gap fails you like in the 1B22s as you are unable to control your input and being variable is a must.
If you need to you can paint the plates with the Radium salts or whatever.

Great stuff with the 1B22s and 811As and an exceptional appreciation from me for providing all the bench type construction detail without the suffocating Math.
All the Best.

Smokey

[Aaron]

Hello All,
Every time I do something here in the new format, I get an invalid URL message and that included the 'Sign In'.

Can you post some screeshots and specifics in here? http://www.energeticforum.com/forum/...port-bugs-here

[aminnovations]

Hi Smokey,

Thank you for all your support. I haven't tried the experiments with a plasma in the spark gap, sounds interesting, and I will look into giving it a try.

I can see there are a good few references to Chernetsky's work online regarding his 'Self-Generating Discharge', and a few for Carson's 'Rotary Electromagnetic Converter'. Are there any online or available details regarding your 'Impulse Discharge' principle and/or device, I would like to take a look at this as well ?

Best wishes,
Adrian

[David G Dawson]

Hello Adrian,
Thank You for responding and also for providing all of your construction detail.

I am attempting to add the attachments but having difficulty and will advise. 'Share Photos' and 'Upload attachments' are both dead. Anybody?
Solved - go to bottom left hand side of your Post to 'Upload Attachments' and as you drag an attachment over it highlights itself and you just drop it in and then you are able to insert into your Post in varying sizes.
Have your space ready for where you want the picture.
Excellent work Aaron!

Impulse Discharge at work.jpg

'Impulse Discharge' was an accidental discovery when doing the Bruce Perrault Ion Valve and Don Smith's Flyback type research.
I, at times do things a little different to the norm and do experiment as I experiment and in such, you get the Dollard 'out of the box' experience.

I am using Bruce's and Bob Ianinni's Pulse Generator (Plasma Ion Pump) which I modified for a greater frequency range and works well with any Flyback and noted the frequency at the discovery was about 75.76 Khz. The ceramic capacitors are in series with the total measuring 19pF - 10 x 100pF.
20 Kv Ceramics in series, I believe, also give you an OU burst, difficult to explain as do oil filled capacitors.
The Spark Gap is using Carbon rods from ' D' batteries and as you can see, the gap is quite wide with the spark extinguished and a plasma connection instead - no noise, no maintenance, no light.
A vacuum tube glass encased variable vacuum tube capacitor would be a probable answer here to the 1B22 but they are most difficult to come by today.

Don Smith Variant circuit.jpg

I am most fortunate in that in my early research years I did most of my purchasing from the USA of things that were simply not available here in Oz and that included all the good Tubes plus oil filled capacitors, HV Caps and Neon transformers etc.
These capacitors are across the Flyback with the Spark Gap on one leg of the HVM 12 kV high voltage diodes.
The German Blaupunkt TV Flyback is probably a 9 kV and uses a Tripler to get the required 27 kV. This is a future modification to triple the voltage but still awaiting the action.
Philips and Blaupunkt in Australia would be like GE and RCA in the USA.
Current at input went from 21 to 7 mA but as you can see the caps are holding 1.1 Kv voltage and continue to charge. Probe is 1,000:1.
Caps are oil filled 8uF in parallel at 4 Kv.

At this point I declared an OU success but the real problem was down converting (DC) what was stored in the caps to a useable 110/240 volt.
I tried further spark gaps and wasted much time with Gas Discharge devices but all to no avail. I was fully lighting a 240 volt lamp at a one second pulse but was clearly unreliable and also blew many with over voltage in the fiddling process.

At this point, along came Eric Dollard with his Vacuum Tubes (VT) and he responded marvellously at my request with a whole heap of VT designs, all of which I built and still waiting to use some of but the focus was on Thyratrons as these were seen to be the answer to my DC problem.
Reason why I built the Cosmic Ray Detector (CRD)(OA4G) and the TMT or Crystal/Radio Set Initiative (CSI) Pulse Generator (2050) to gain further Thyratron experience.

Dollard Cosmic Ray Detector working2.jpg
Dollard TMT Pulser & Receiver & 6SN7 Amplifier2.jpg

At this point I have made no further progress as I have about six (6) other hopeful OU projects on the bench and all requiring attention but had to stop as I had run out of room and that is still what I am working on. I am also rainmaking and that is also taking much of my time here due to the extreme Drought (and Fires) and I only discovered that my prime device was working poorly since early 2018 and not at all happy about my inattention.

So what I am suggesting here is the use of the plasma and suggesting the variable vacuum tube capacitor in place of the 1B22. I have one large here but not variable but would be worthy of experiment with variable input control of both frequency and voltage.
This is also where Bruce Perrault comes into the picture with his Ion Valve which is another plasma device but can be built to use without a vacuum and can also be assisted by radiation metals and have included a picture my own efforts in Copper, Aluminium and Carbon as an example and using active welding rods as the Anode - see attached.

Ion Valves 2011 04 22.jpg
DSmith L1 & L2.jpg

Eric would be best to contact for information on the Chris Carson Generator and I use it only as an illustration of the way variable plates are available for high voltage plasma operation. We don't require the physical rotation here which is why my Yahoo Forum is called 'torsion' as that is what I do - energy rotation without the physicals.

You are welcome to join me (and others too if interested) at the newly formed 'smokey9s@groups.io' and the old 'torsiondevices@yahoogroups.com' where all of my information is held but will continue to Post here in recognition of Eric Dollard's exceptional assistance even though I still don't like his Math.

Will welcome questions from anybody interested in this phenomena.

Smokey

[aminnovations]

Hi Smokey,

That's really great! ... thank you ... this is a lot of detail for me to look into, and I also appreciate all the practical info, pictures, and shared know-how, and I have joined your newly formed group.

I also invested in many of the high-voltage components, tubes, transformers etc. back in the early days (2003 onwards), which mostly came from the US, Russia, and the Ukraine. I was particularly fortunate to come across a US surplus supplier that was selling a job-lot of 1B22 tubes, 4 of them unused, 3 used, and 1 defective (no gas but still working as a spark gap).

Anyway, I am going to take a look at a plasma in the spark gap and see what I can do with it. I want to try driving my TMT experiment that I am currently using in my sequence on the Transference of Electric Power, and see how this type of generator will change/improve/modify the properties/phenomena observed in the experiment.

I have previously created a plasma in the spark gap using a MOT, (microwave oven transformer), which had no current limit in the primary, so the spark discharge was very quickly replaced by a hot quiet plasma. However, this method wasn't easily controlled even with a primary choke, the frequency is only the line frequency, and it was easy to burn out everything with the MOT, and including the secondary winding of the MOT.

What you are suggesting with your 'Impulse Discharge' looks like it would be much more controlled and measured.

Best wishes,
Adrian

[Marcus Neuhof]

Adrian, unfortunately I have been very busy and still am working my way through your posts, but will no doubt have comments for you later. Thank you in any case!

Aaron, earlier I saw a post -- but can not find it now -- where you asked for people who had previously worked on Cris Carson style generators. If you search my posting here you will find a series of posts I did regarding an attempt to replicate Eric Dollard's "voltage converter", which is electrically similar.

[aminnovations]

Hi,

I have added a new post to my website:

http://www.am-innovations.com/vector...nalyser-dg8saq

This post on the Vector Network Analyser (VNA), the DG8SAQ by SDR-Kits, is the first in a sequence looking at how to use advanced test equipment to measure the properties, characteristics, and electrical parameters associated with Tesla coils and TMT transmission systems. The post includes two videos covering setup, calibration, measurement, and software, which forms a step-by-step introduction to get up and running in measuring the impedance properties of Tesla coils using this very functional and yet cost-effective VNA.

The videos are intended to demonstrate the following:

1. An introduction to Tesla coil measurements using a usb connected vector network analyser.

2. Connecting the VNA directly to the secondary of a Tesla coil for series-fed measurements.

3. Connecting the VNA to the primary of a Tesla coil to measure Z₁₁, the small signal input impedance from the perspective of the generator.

4. Connection considerations and methods when using coaxial, and twisted-pair cables.

5. Consideration of calibration reference plane, and techniques to extend the reference plane directly to the primary coil inputs.

6. Calibration of the VNA for Z₁₁ measurements using a short, open, and 50Ω termination.

7. The VNWA software to calibrate, measure, display, and store the data.

Best wishes,
Adrian

[David G Dawson]

Farnsworth's Multipactor Tube:

https://borderlandsciences.org/journ...ctor_Tube.html

Hello Eric,
As you spent many hours working with Philo, is there anything that you may like to add with respect this device.
No filaments, no grids and a cold cathode device.
You made a comment in the 'Functional Thinking' interview with Thomas Brown that you believed it was - "probably the only real free energy device that anyone ever demonstarted which can be reproduced"

https://pdfslide.net/documents/funct...-brownocr.html

Also you made comment - "Free energy will never come out of magnetism unless the magnetism is tricked with hysteresis".
Hysteresis meaning magnetic retardation or inertia.
Would you please expand on this statement.

Thank You.
Trusting all is well with you.

Smokey

[David G Dawson]

Radio World - Multipactor:

https://www.americanradiohistory.com...multipactor%22

More on the Multipactor and found only one entry in the above magazine and from there guessed where it all went - into suppression.
Soon as you here 'negative resistance' and 'secondary emission' and '20db down' from a cold cathode tube you must expect something in return that it will never be heard of again and such is the case.
Reason why I have a stash of 24As here and also Eric's 6AS7 and similar.
Note that the mention is of certain groups holding all the Patents for Oscillators and they didn't like this one because it was too close to something being free.
It pays to read these old magazines to find out what you are really missing out on when it comes to 'Energy Synthesis' as they do hold a great deal of odd material on discoveries that are soon to be no longer heard of.

Going through all of my Tubes here to see which ones come closest to a Multipactor.

https://www.americanradiohistory.com/index.htm

Welcome to the Matrix!

Smokey

[Aaron]

Hi,

I have added a new post to my website:

I got those two vacuum variable capacitors from Ukraine finally - will get on the mounting stuff soon. I might as well either post that here or start a new thread on the project I'm building.

[Aaron]

Farnsworth's Multipactor Tube:

https://borderlandsciences.org/journ...ctor_Tube.html

Hello Eric,
As you spent many hours working with Philo, is there anything that you may like to add with respect this device.
No filaments, no grids and a cold cathode device.
You made a comment in the 'Functional Thinking' interview with Thomas Brown that you believed it was - "probably the only real free energy device that anyone ever demonstarted which can be reproduced"

David, we're going to do another live call sometime in the near future if you want to get on and talk to Eric directly about this.

[nothing]

David, we're going to do another live call sometime in the near future if you want to get on and talk to Eric directly about this.

Aaron,

Please let me know if you and/or Mr. Dollard
are willing to take a look at a mathematical 'identity'
which simultaneously equals both 1 and Φ³
An example of plotting this one expression
into a random math website:

h1.jpg

I believe this identity is extremely important
as it relates to electromagnetism
and/or sacred/universal geometry.

I believe it solves a number of the outstanding Millennium Problems - certainly the Reimann Hypothesis,
thus I want an actual electrical engineer / experimentalist who knows the math to see it.

Please pm me so I can get it to you.

Thanks Aaron,

[Aaron]

Aaron,

Please let me know if you and/or Mr. Dollard
are willing to take a look at a mathematical 'identity'
which simultaneously equals both 1 and Φ³

That would be a question for Eric as I don't understand the math well enough. I'd recommend writing to him at his Lone Pine address, which is listed on http://ericpdollard.com. That is the best way to get a personal response from him.

[Aaron]

ERIC DOLLARD LIVE CALL COMING SATURDAY

Call in for the latest updates and ask Eric Dollard questions live - Saturday, February 8th, NOON Pacific Time Zone. Call +1 857-232-0155 and enter the code 582590 to access the call. In the meantime, consider donating to EPD Laboratories, Inc to support the work of Eric Dollard. Information on donating by mail or by PayPal are on http://ericpdollard.com