Announcement

Collapse
No announcement yet.

Figuera Device, Part G Continuum.( Serious Builders Only)

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Doner

    Well folks another donor has spoken Mr John has made a very generous donation to the advancement and distribution of the Figuera device.

    our world needs cheep clean abundant energy if we are to survive the very trying and troublesome times a head. i as a very knowledgeable person of the Figuera device and will do everything i possibly can to bring this device to the face of every human i possibly can.

    every donation, even one single dollar, brings us that much closer to a environmentally safe power supply that EVERY person in this world should have access to. imagine driving your car free from pollutants, houses powered by your device free for the rest of your life, or even growing fresh fruits and vegetables 24/7 365 days a week free from corporate America's poisons and greed to control us. this device can make this all happen and thanks to john, half way around the world, thinks this can happen to

    Thank you John.

    MM
    Last edited by marathonman; 11-12-2016, 01:10 AM.

    Comment


    • Part G and Recycling

      I guess the confusion was the way i described the power recycling. it is not actually back and forth between part G and the primaries. see as the low primary's power is shoved into part G and stored in the form of a magnetic field, it is fed every half turn. when the system needs power it takes it from the magnetic field converted to currant to be circulated around to the primaries on the negative side not back and forth between them. so i see where this would bring on some confusion. part G feeds the primaries after the power supply is removed, the primaries feed part G and the second secondary replaces losses occured in the process.
      the currant stays in the same direction at all times even when the primaries are feeding part G.
      thus the power is recycled.

      hope this eases some confusion.


      MM
      Last edited by marathonman; 11-16-2016, 03:53 AM.

      Comment


      • Primary winding and connection

        The below pick is taken from the patent. the black arrows are correct. as i have been saying to wind your primaries from the secondary side North to the outside South CCW. the south end or rear of the core is connected to part G. the patent clearly shows this but the arrow in red is wrong and the blue is corrected. ALL negative connections are to the front of the coil facing the secondary and the rear of the coil is connected to part G. this was purposely drawn to throw you off. both set are wired just the same as mirrored sets so set S should be wired just like set N in black.
        even though it is just a drawing drawn in elementary form, some things just are the way they are. power enters in front, exits out the back under pressure to part G. kind of reminds me of a turbo, the exhaust turns the turbo that feeds the intake that boost the power. thus a recycle of energy.



        MM
        Last edited by marathonman; 11-18-2016, 07:57 AM.

        Comment


        • Thanks

          MM thank you for the pictures of your part "G" I ordered my copper this morning.
          I finished gluing my three cores a few minutes ago.
          Thanks again,

          Shadow

          Comment


          • Part G

            I hope you used 8 or 10 awg as that is much cheaper and easier to work with. i would also suggest those lugs UFOP and i were talking about. much easier installation and adjustment. just remember to flip the center part before installation. Home Depot has those lugs for 10 dollars for 10 and the 8 awg solid ground wire is only 59 cents a foot.

            From the donations i have received i will be able to order the electronics for the timing board in the next few days and begin my testing and adjustments of it and part G.
            i am working on a video explaning the Figuera device as a whole then individual parts opperation and why i am doing what i am doing.
            one whole video will be dedicated just to part G, it's wonderful opperations and why near zero ohms is so necessary.

            always remember inductance from the windings amplified by the core controlls the currant NOT the resistance of the wire. resistance only causes wasted power through heat in part G and the primaries so wind part G and your primaries with as little resistance as possible using thick wire and not according to modern day winding technics. the secondary and second secondary is the only item in Figuera's device that is wound according to modern winding technics. other exceptions are the Tesla AC to DC device.

            pics of primary, secondary and core will be posted in a few days, just tying loose ends.

            Happy part G'ing my friend.

            MM
            Last edited by marathonman; 11-18-2016, 08:47 AM.

            Comment


            • Copper

              I should be getting my .375X.125 Copper today or Monday for $36.12 plus shipping!

              Good luck,

              Shadow

              Comment


              • Annealing Copper

                The copper I am buying is 1/2 hard. Here is a tutorial on copper annealing. I suspect it may need annealing.

                https://www.youtube.com/watch?v=3jSz11lz8MA

                Shadow

                Comment


                • Annealing

                  Why in the world would you want to do this.??

                  when purchasing Home Depot's #8 solid ground wire i checked and price was only 45 cent a foot.

                  picking up 14 awg wire tomorrow for primaries from EIS.


                  MM

                  Comment


                  • Ouch !

                    EIS did not have 14 awg on hand. like most corporate America, they are cutting supply thus direct signs times are getting bad. wire will be here in a few days. my primaries will be rewound then pics will be posted. remember to always follow winding guidelines i have posted.

                    we need to get these devices built before crap hits the fan. as i understand it the Rothschilds and the Rockefellers are planning to crash the market now that Trump is in office. i just hope we are finished with this device by then.

                    i have pure iron core that i will be using as that is what i have on hand. i can't afford anything else and haven't the funds for laminated cores or haven't found free transformer cores.

                    the pic i have is the pure iron cores cut to stop eddy currants from secondary to primary before rewinding with 14 awg wire.
                    i will update as soon as possible.





                    MM

                    Comment


                    • Ha...bad luck!

                      Oops!
                      You are right..........I got caught up in the picture of the copper strips you posted on the eight and ninth.
                      Oh well, I can get Number 8 locally a lot quicker.

                      Comment


                      • Originally posted by marathonman View Post
                        EIS did not have 14 awg on hand. like most corporate America, they are cutting supply thus direct signs times are getting bad. wire will be here in a few days. my primaries will be rewound then pics will be posted. remember to always follow winding guidelines i have posted.

                        we need to get these devices built before crap hits the fan. as i understand it the Rothschilds and the Rockefellers are planning to crash the market now that Trump is in office. i just hope we are finished with this device by then.

                        i have pure iron core that i will be using as that is what i have on hand. i can't afford anything else and haven't the funds for laminated cores or haven't found free transformer cores.

                        the pic i have is the pure iron cores cut to stop eddy currants from secondary to primary before rewinding with 14 awg wire.
                        i will update as soon as possible.





                        MM
                        Hi Mm, are the cores you are using mild steel or pure soft iron, and what diameter?.

                        Nearly finished harvest, will start build shortly.

                        Best Regards Cornboy.

                        Comment


                        • Cores

                          Quote;

                          "the pic i have is the pure iron cores cut to stop eddy currants from secondary to primary before rewinding with 14 awg wire."

                          That my fellow builder is self explanatory but the purity is 98.8 if i am correct and the diameter is 2 inches.

                          please do not feel compelled to buy this stuff as pure iron is absolutely disgusting in price and you would be better off buying a three phase transformer and stripping it for less. it will accomplish the same thing.

                          still drooling over that garlic.

                          Shadow;
                          8 awg ground wire will get you there safely my friend with less headache.

                          MM

                          Comment


                          • Yeah, just can't find pure iron rod in Aus, for love or money.

                            Will probably use either sprayed copper coated mild steel welding rods 1.6mm dia, or iron powder with epoxy, for cores.

                            I have left over 30mm id bobbins 75mm long for primaries, and will halve the length for secondaries, probably a string of 5 electromagnets, one for power to run device.

                            regards Cornboy.

                            Comment


                            • About my build...

                              Hello to All,

                              This post is basically for those building Part G with heavy gauge wire as low turns...plus if any of you are thinking of powering up Toroid and Primaries (I will refer to as the "Exciter Circuit" as a whole assembly) with a "Regulated Switching Output" PSU.

                              First off I used my brand new "Switching Regulated" PSU that I have posted previously...a "Circuit Specialist" brand name which "supposedly" delivered 60V driving 10 Amps...in order to power up the Exciter Circuit simultaneously regardless of resistance...plain and simple BS!

                              Power Source of this kind will never, ever deliver full VA with such low resistance values at Toroid plus Primaries...period!...it will raise amps to max (10 A) but Voltage will remain around 2 Volts...which will never, ever generate the required magnetic field at either one of the three components of the exciter circuit.

                              We will need a LINEAR (not switched) Old type Transformer and heavy diode bridge from AC wall outlet with suitable potentiometers to regulate V and A separately....with nothing more as a "built in protection circuit" that a mere VA Rated Fuse. Then we must start dialing output very slow and precise while driving our Rotary switching either mechanical or electronic (Solid State).

                              So, if we still have no other recourse but to keep using this kind of regulated switching PSU...then we will need to increase Resistance by higher number of turns...and maybe a not that heavy wire at all Exciter Components.

                              Below are some pics of my set up:

                              From previous post where I uploaded the wound Toroid...I wrote that I am using 20 Turns of 8 awg bare wire, as also a 20 elements commutator at switching, well, same spec's with this test:

                              [IMG][/IMG]

                              I used 3/16 copper tubing to attach to each comm element...

                              [IMG][/IMG]

                              Above you can notice I ran 10 gauge stranded wire all the way out of the "L" tubing, then press it at end, plus at commutator element ends with a modified by me Heavy duty and huge Pliers which I used before to put together hydraulic lifts steel cables...then melted soldering at both ends of "L" copper tubing with my 175 Watts Gun:

                              [IMG][/IMG]

                              [IMG][/IMG]

                              Above pic is the whole set up wired up...

                              And yeah...it looks great...but it don't work with my PSU...

                              The way I see this whole Circuit...there are some main aspects We all must have in mind in order for this System to work as we all expect it to...

                              1- First than all, at Toroid Part G Core we must Generate/Develop the suitable Magnetic Field in order for it to regulate Currents at both outputs (Hi-Lo) based on pure Inductance and Reluctance.

                              And so...in order to build this suitable magnetic field within a T-Iron Core of around 1800 plus VA rating...we need to calculate the suitable Amps-Turns per square area based on our VA Input.

                              And here, IMHO we need to apply the Ohm Law for Magnetic Circuits...or else we all would be winding toroids for a while here...with all kind of different wire awg and number of turns spec's...

                              As I would like to ask Netica about his set up and spec's* of the Toroid wound he used...and I know he was testing just 12V...still it would be a good start to use some calculations from there.

                              @Netica the Spec's* am referring specifically to are: Toroid core VA rating or thickness and ID + OD, as number of turns and type of awg wire that you used in the shown test which gave you that Scope signal. (linked to post)

                              @Cadman: How is your build coming out my friend?...Any results yet?

                              As we construct here...we must post our failures as our positive results, with all the specifics for either results...as I believe it would serve others not to spend their time with a set up which would not work properly. It is the only way I can see that we all would advance here.


                              Regards to All


                              Ufopolitics
                              Last edited by Ufopolitics; 11-22-2016, 02:08 PM.
                              Principles for the Development of a Complete Mind: Study the science of art. Study the art of science. Develop your senses- especially learn how to see. Realize that everything connects to everything else.― Leonardo da Vinci

                              Comment


                              • Part G

                                Now why do you think Figuera used a deep core and thick wire...... more core exposure. since you have the core already try doubling the winding count on part G and use tap at every other wind. all that is happening is not enough inductance due to not enough winding's exposure to core material. do not throw wire away just add to it.

                                i have posted the formula for inductance.

                                HIGH OHMS IS NOT THE WAY TO GO TO COMBAT LOW INDUCTANCE MY FRIEND.

                                Cornboy;

                                i would suggest laminated transformer core and not powdered iron or rods as you will be wasting your time and money. old or even burnt transformers will work fine. i would be doing this if i could afford it as i found a 75 va three phase for 199 on ebay. enough for an entire build.

                                the pick i posted will have the secondary bobbin increased by almost 1/2 inch larger and cores are resined back together.

                                MM
                                Last edited by marathonman; 11-22-2016, 03:03 PM.

                                Comment

                                Working...
                                X