No announcement yet.

Magnet motor revelation

  • Filter
  • Time
  • Show
Clear All
new posts

  • MadMack resurfaces

    Been over 3 years since MadMack posted on this forum. Although I did not participate when this thread was active, I did watch it and always wondered about this guy. I stumbled across him on overunity dotcom yesterday.
    I wonder if there is a deeper connection between MadMack and IEC.

    You decide.

    But from the beginning, I felt MadMack had gotten stuck on his development and was fishing the membership here for a solution.

    Notice that UfoPolitics, nor anybody else, has shown a working magnet motor. Maybe this Earth Engine? I'm not holding my breath.




    • Magnetic engine principles are everywhere on the web. Flux splitting
      and other ideas. Those who have perfected their engines date back
      as far as the 50's and are not likely to hand over the data for free.

      Also just because an engines runs not stop, proving science has missed
      the boat in text book form, does not make every design practical. Cost
      effectiveness is another consideration.

      Anyone one having a design capable of threatening the fossil fuels models
      are deemed a national security issue. An offer they cannot refuse is
      potentially the next step to eliminate the opposition.

      10 million is cheap compared to the trillions brought in year after year.


      • Good point, there are so many rotating magnet motors on the
        web with no real pulling power, they just go round. Like that V-Gate
        it can't take much loading in most cases and is one of the best ones out
        there. Well the V-Gate splits the flux and dominates on youtube.

        Tesla had the right idea when he changed the standard motor coils out
        that dog down a motor for coils that use the right timing to assist the
        rotor. There has got to be a way to implement split flux principles that
        offer plenty of excess power.

        Like the SEG there is much to learn about shielding with copper, poly
        spacers, aluminum, not so much just to contain the magnetic energy
        but redirect and store it. As soon as you push on a magnetic field it
        moves over trying to find a place to jump so why not capture and
        redirect if possible? Mad mack said shielding was key and we have
        devoted almost no time to it.

        There should be a benefit for any motor just using the "Y" elements idea.
        Last edited by BroMikey; 04-14-2019, 06:54 AM.


        • All permanent magnet motor.

          You need a very large 7.5 inch (255 mm ) dameter round ceramic magnet to start making the motor. Next you need a 8 mm diameter non magnetic shaft placed dead center in a vertical fixed position. About 12 inches long.

          Now you need a very thin wood 7.5 inch diameter disk. A 7.5 inch record with center plug will do. A Hole of 8 mm is drilled in the center. A 5 1/2 inch circle is drawn next on the disk top. A centering tube that has a 8 mm hole through it is glued onto the center of the disk so it is free to rotate without wobble on the 8 mm diameter shaft coming out of the ceramic magnet disk.

          Now we come to the important part. You will need four 45 degree wooden or aluminum angles and bond them securely to the 5 1/2 inch drawn circle so the angle ends will be centered on the drawn line. Now you need 4 grade N52 large block magnets and epoxy them one at a time on top of the 45 degree angles insuring that each one sets up first otherwise you will find magnet hopping.

          The polarity of the magnets on the 45 degree angle must all be the same as the polarity of the ceramic magnet they face. This is extremely important!!!

          Now when the wood or record disk is placed onto the ceramic magnet shaft it will rise up/float and should rotate also because of the magnet angle displacement.

          If you get your disk to rotate then suspend a 1000 ohm or more coil with a one inch cener hole in it over the rotating disk magnet tops. The one inch hole should have a 3/4 inch N52 grade sphere magnet inside it so it's free to spin side to side. Connect 3 volt led lamps in parrall to the coil leads and watch the light show.

          I am into this right now and working on the disk magnets presently.
          My biggest hope is the disk will spin. This below photo is my newest. I am steady improving this as I go along. You need to be certain that the 4 disk magnets are centered directly over the most powerful
          Area of the large ceramic magnet. A 5 1/2 inch or 5 inch circle drawn over that area is where the 4 disk magnets are centered apart from each other. Check out that area out on your ceramic ring magnet first before you do anything. Might vary from my ceramic magnet.

          Open for thoughts on this.

          Attached Files
          Last edited by magnetman12003; 09-22-2019, 02:34 AM. Reason: Show photo


          • Hi Tom

            Not sure I can visualize the layout, can you draw a picture for us?
            I hope it does what you want. Keep me and the group posted on how
            it all turns out. Maybe if you have it near laid out we could see a video
            instead, whatever works best for you.


            • Progress

              Any word from Mac on his NEW setup?
              “Advances are made by answering questions. Discoveries are made by questioning answers.”
              —Bernhard Haisch, Astrophysicist


              • Hi Dave,

                If you want some info that might help you build a working magnet motor. Check out my video in the open discussion thread.

                If you have any questions just email me and we can discuss them. I don't discuss projects on this forum anymore.

                Take care,
                Just because someone disagrees with you does NOT make them your enemy. We can disagree without attacking someone. This means YOU especially BroMikey.


                • Here is one for you Mack

                  Last edited by BroMikey; 03-29-2020, 09:10 PM.


                  • Hey people... I come across on the following page, a copy of an article from an old , deceased now kelynet website ... Seems to be a very simple design of Robert calloway magnetic motor successful replicated by somebody ... is not given any schematic but are explained in detail ... because of language barrier ,was dificult to me to understand clearly some details.... I post the link here ,maybe somebody will understand better the explanations given in that design :


                    • Some time I also started to try different configurations for the magnet motor, but in the end I was with the retention and neutralization of the fields, in YouTube video a person almost achieved the perfect movement but almost at the end and when starting the route again of the rotor ran into the magnetic lock,
                      Well I said this person almost succeeds, but what happens if you put a bedini coil that from the closing push at the beginning of the tour, so it would have its almost magnet motor with a small help of a coil, the magnets in repulsion would give a good torque to the rotation of the rotor, and the coil would give the thrust to pass the magnetic lock, based on this idea I will work


                        Just because someone disagrees with you does NOT make them your enemy. We can disagree without attacking someone. This means YOU especially BroMikey.