Barbosa and Leal Devices - Info and Replication Details

[edwins]

Hello edwins,

I don't know why people keep thinking I have a working GROUND generator when I do not. I have stated many many times in a lot of past post that my unit is actually no better than an any battery and large watt inverter set up.
the REASON for this is due to MY LOCATION!!!!! the earth crust magnetic anomaly for my location is somewhere around a - (negative) 30 nTesla value
which is so piss poor it took me a total of 60 ground rods just to get it
to perform as well as the plain ole battery - inverter set up I mentioned
earlier.

my advise to everyone is to first check the earth crust magnetic anomaly for
their location and if it is not at least a + 140 nTesla value then don't waste your time and money.
Also DO NOT TRY THE SMARTPHONE pullup of the earths nTesla value for ANY magnetic anomaly because all you will get is the same old misleading trash I have seen a lot of others spouting about lately. I haven't said anything about it before but that's just what it is! TRASH! use the values stated on an ACTUAL magnetic map of the anomaly for your area!


this is the map info I used (way to late sad to say) .
the smartphone pull up does not even give the supposed Tesla value in the correct denomination either.

If anything that is worth doing it is always worth doing correctly!

regards,

Clarence

Hello Clarence,

I find it hard to look for the earth magnetic anomaly in our place. Would it be possible to ask help from you about the nTesla in our place(Cebu City, Philippines)?

Thank you very brother!

Edwins

[edwins]

Hello edwins,

here it is! the blank spots are simply places they were not allowed to enter at time of making their magnetic map.


the red zones are the good spots and blue is the poorest. the green and
yellow are the same as my location - piss poor! hope you are in the red area!

Best Of Regards,

Clarence

Clarence,

Thank you very much brother!
I belong to the blue zone.

Edwins

[edwins]

Clarence,

Thank you very much brother!
I belong to the blue zone.

Edwins

Clarence,

Brother i have to inquiries:

What is the size of the thick black wire wrap around the two toroids as secondaries?

What is the size of the red wire(connected to the ground) wrap around the thick black wire?

Thanks
Edwins

[clarence]

Clarence,

Brother i have to inquiries:

What is the size of the thick black wire wrap around the two toroids as secondaries?

What is the size of the red wire(connected to the ground) wrap around the thick black wire?

Thanks
Edwins

Hello edwins,

I see you make the same mistake as everyone does!
the so called red wire is just a reconstruct of previous schematic info posted on this thread!

the color of the wire is and should be GREEN!!!! its the international color code for GROUND or GROUND WIRES! I assume whoever highlighted the wire just used red to illustrate a particular point he was trying to make?
this is the actual set up for the EARTH GROUND RETURN WIRE!

Also use this schematic - it is a lot more detailed and specific.


also I am wondering why you are wanting these details since you are in the blue zone????????????? that would be a mistake for sure!

the black wire is tinned multistranded # 4 AWG.

the GREEN wire is tinned multistranded # 6 AWG.

Regards,

Clarence

[edwins]

Hello edwins,

I see you make the same mistake as everyone does!
the so called red wire is just a reconstruct of previous schematic info posted on this thread!

the color of the wire is and should be GREEN!!!! its the international color code for GROUND or GROUND WIRES! I assume whoever highlighted the wire just used red to illustrate a particular point he was trying to make?
this is the actual set up for the EARTH GROUND RETURN WIRE!

Also use this schematic - it is a lot more detailed and specific.


also I am wondering why you are wanting these details since you are in the blue zone????????????? that would be a mistake for sure!

the black wire is tinned multistranded # 4 AWG.

the GREEN wire is tinned multistranded # 6 AWG.

Regards,

Clarence

Thank you Clarence. The schematic is more detailed.
We have some place in the red zone.

Edwins

[clarence]

Understood now!

Hello edwins,

Now I understand the WHY for your questions!!!!

Also if you need more info don't hesitate!

BEST regards,

Clarence

[clarence]

[QUOTE=BroMikey;

Hello BroMikey,

I finally finished the IFT module and ran it and put it through it's paces however the results were a mixed bag at best!
Nothing would stay stable for a long enough period to be able to have anything usable to be able to work with.
the end output was low acv and barely enough amperage to be able to see only a small glimmer on a mere 4 watt night lite bulb.
was really aggravating to have spent all the time and effort into the attempt to get rid of the high frequency in order to be able to use the 122 acv output from the large TBC coil.

Its the same age old problem that Tesla, DS, and countless others have tried to deal with.
once a set high frequency is introduced into any system, that frequency is there forever until the initial system is destroyed. this will be one of my next
moves. to divide the HF into smaller voltage increments and then rectify each divide to DC voltage suitable for powering 60 HZ inverters at a usable amount for residential devices and appliances.

one additional method I have already started is using the magnetic flux from the TBC coil to empower a charge method other than the smart charger which uses up way to much amperage to be profitable in my view.

Time will tell which method works the best!

Regards,

Clarence

[BroMikey]

Hello BroMikey,

I finally finished the IFT module and ran it and put it through it's
paces however the results were a mixed bag at best!
Nothing would stay stable for a long enough period to be able to
have anything usable to be able to work with.
the end output was low acv and barely enough amperage to be
able to see only a small glimmer on a mere 4 watt night lite bulb.
was really aggravating to have spent all the time and effort into
the attempt to get rid of the high frequency in order to be able
to use the 122 acv output from the large TBC coil.

Its the same age old problem that Tesla, DS, and countless others
have tried to deal with.
once a set high frequency is introduced into any system, that
frequency is there forever until the initial system is destroyed.
this will be one of my next
moves. to divide the HF into smaller voltage increments and then
rectify each divide to DC voltage suitable for powering 60 HZ
inverters at a usable amount in residential devices and appliances.

one additional method I have already started is using the magnetic
flux from the TBC coil to empower a charge method other than the
smart charger which uses up way to much amperage to be profitable
in my view.

Time will tell which method works the best!

Regards,

Clarence

Wow that sounds like a good deal of work accomplished. I am looking
forward to your results over time. This is a very advanced work so don't
be surprised if not many are able to follow in your foot steps.

I think that the first stage can be run showing the extra using lights
while your research continues on the refinements for powering all
120vac devices.

You will find a way to isolate.

[edwins]

Hello edwins,

Now I understand the WHY for your questions!!!!

Also if you need more info don't hesitate!

BEST regards,

Clarence

Thank you brother!

Edwins

[jim glinski]

frequency dump

Hi Clarence
Have you tried a pi filter to remove any unwanted hi frequency?
I guess you've tried a square wave inverter and it didn't work ? Not just relying on the patent info?

[jim glinski]

Any one have the link to the earth ground electrical maps ?

[Jeff Pearson]

Earth Magnetic Anomaly Grid

I use the plugin for Google Earth. I am in a dark blue to black zone.

[jim glinski]

Thanks Jeff

[luc2010]

Hello to All,


Can DC motor (12v) acts as spark gap providing pulsed DC?

i am trying to avoid electronics!! in order to create HF low voltage (12 v battery) to replicate the latset circuit!!!


Best Regards
luc2010

[jim glinski]

luc2010

I don't know about hf but I have striped down a small DC motor and shorted out the commutator windings removing remaining wires and iron core material and magnets to make a rotating switch . going to run it with a five dollar 555 timer circuit and another DC motor for variable speed control . I did this because bedini said you needed a laith to make a carbon brush rotation switch . so I tried this and it was OK. Jim