Barbosa and Leal Devices - Info and Replication Details

[BroMikey]

A Brief Synopsis of past events

Hi Clarence,
any news on your project?

What was the maximum load that you test it with your device and the 60 ground rods without the voltage drop? I guess it was below 2kW?

Thanks a lot!

J.

As you saw Clarence is very busy but from what I know the 60 ground
rod B&L device ran lights and a refrigerator during the daylight hours.

He has more than one setup now and from what I understand
less rods will be needed if any. I think Clarence is trying to change
his systems dependency on so many rods so he is combining his new
experimental device with the B&L device.

But in the beginning you are correct, use 60 rods was the instruction
and the output was enough to power many things. If you look back in
the record you will see that the refrigerator ran for about 5 hours at
times and the battery would begin to discharge some. He would stop
the system and charge it so he didn't destroy the battery and repeat
the process over and over again getting excellent runtime powering
devices all day. No grid power, only a battery and sinewave inverter
as the source and I am sure you knew that.

Clarence went on to say that he wanted to get more power and runtime
without ANY downtime so he thought to add more rods to see if he
could increase the outputs, however not all geological locations offer
the same amount abundance of telluric earth currents as the next
region and may pose a cost effective limit.

[BroMikey]

Hello @ ALL,

was having difficulty with out put of TBC,s. then finally went back through each component one by one and found the 500uf cap was not even connected internally when made at the factory!

so am revising circuit harness and will just find results on only one of the TBC,s. will be able later to repair the cap myself. don't want to go thru the
slow boat from china routine again for certain.
will take a day or so - busy as hell on the farm this this early winter time for certain.
rest easy.

LATER!

Clarence

hey Clarence

Good to hear from you. I had a similar problem like you did with parts
and I had to wait twice now to get what I needed on another project
but they sent me a free one each time.

You will get what you need and your success will shatter all of the
university models like it always does. Whoever heard of getting energy
from the ground or from what looks like "NOWHERE"?? Who is going to
believe you?

I saw a guy on youtube in tears over people calling him everything but
late for dinner and he said he was giving up posting all of his devices.
People are calling him names very vulgarly I suppose, isn't that special?

I guess he thinks he's the only one. Of course we understand what he is
going through. I mean people want it tipped upside down and turned
inside out thinking it is another trick video.

And if a project has capacitors they will claim that there must be a
miniature nuclear watch battery powering the whole house right?

What a world of disbelief we live in. No worries mate, I believe you.
Looks like your cap terminal turned to Swiss cheese.

[clarence]

Capacitor fail at manufacture

Hello @ ALL,

was having difficulty with out put of TBC,s. then finally went back through each component one by one and found the 500uf cap was not even connected internally when made at the factory!

so am revising circuit harness and will just find results on only one of the TBC,s. will be able later to repair the cap myself. don't want to go thru the
slow boat from china routine again for certain.
will take a day or so - busy as hell on the farm this this early winter time for certain.
rest easy.

LATER!

Clarence

[jazzzyro]

Hello BroMikey,

Again, thanks!
went to E-Bay site and believe I found what I needed for 99.00 bucks.

will take about two weeks for delivery - but OH WELL!

actually bought in the deal 2 ea 500uf 250 acv nonpolarized caps and 4 ea
1000uf 250 acv nonpolarized caps all for the 99.00 bucks.

you can go ahead and delete all the info posts, and many thanks again!!!

Respects,

Clarence

Hi Clarence,
any news on your project?

What was the maximum load that you test it with your device and the 60 ground rods without the voltage drop? I guess it was below 2kW?

Thanks a lot!

J.

[seychelles]

Hi Clarence, my suggestion is to rectified the output and connect the DC output
to a grid tied invertor and that should cost you about 300$.

[BroMikey]

Hello BroMikey,

Again, thanks!
went to E-Bay site and believe I found what I needed for 99.00 bucks.

will take about two weeks for delivery - but OH WELL!

actually bought in the deal 2 ea 500uf 250 acv nonpolarized caps and 4 ea
1000uf 250 acv nonpolarized caps all for the 99.00 bucks.

you can go ahead and delete all the info posts, and many thanks again!!!

Respects,

Clarence

All clear now, glad you found one or two that you could use.
I have a knack for finding parts when I want to.

[clarence]

Re: Capacitor search

Hello BroMikey,

Again, thanks!
went to E-Bay site and believe I found what I needed for 99.00 bucks.

will take about two weeks for delivery - but OH WELL!

actually bought in the deal 2 ea 500uf 250 acv nonpolarized caps and 4 ea
1000uf 250 acv nonpolarized caps all for the 99.00 bucks.

you can go ahead and delete all the info posts, and many thanks again!!!

Respects,

Clarence

[clarence]

Clarence, I would suggest looking at surplus and used suppliers. Recently found some of these at a Ham swap for $8 each : 10000 uf 200 VDC (about 6" tall) I would also contact these people or look at their web site : HSC Electronic Supply - Silicon Valley's Electronic Marketplace which is HSC Electronic supply in Sacramento, California. They have a huge amount of surplus electronics and generally very good prices as they get much of their supply from excess in Silicon Valley. I've bought a lot from them in their brick and mortar store and they have some real deals that are hard to beat. It just will be the luck of the draw though as to whether they have exactly what you need but I'm sure there are a lot of surplus stores elsewhere.

Hello E,

Really glad to hear from you!
I pulled up the site you mentioned but at the moment they didn't have anything I could use. however I bookmarked it for later off and on.
for frequency control I can only use ACV capacitors usually rated for both AC and DC usage. I have two options bookmarked now from Digikey. one is for 400uf 250acv (at 91.00) and the other is for 150uf 250acv (at 48.00).
so that would amount to 3 @ 91 + 1 @ 48 = 321.00 which is a chunk!

the 1350uf with a total inductance of 5.11 mh (TBC of .11mh and
2.5mh+2.5mh from each leg of a common mode inductor choke coil) will set a frequency level of 60.59 HZ.
so that in a nut shell is what I am aiming for.

As I said E, it is good to hear from you again. stay close!

Respects,

Clarence

[ewizard]

Clarence, I would suggest looking at surplus and used suppliers. Recently found some of these at a Ham swap for $8 each : 10000 uf 200 VDC (about 6" tall) I would also contact these people or look at their web site : HSC Electronic Supply - Silicon Valley's Electronic Marketplace which is HSC Electronic supply in Sacramento, California. They have a huge amount of surplus electronics and generally very good prices as they get much of their supply from excess in Silicon Valley. I've bought a lot from them in their brick and mortar store and they have some real deals that are hard to beat. It just will be the luck of the draw though as to whether they have exactly what you need but I'm sure there are a lot of surplus stores elsewhere.

[clarence]

Capacitors for frequency control

Hello @ All,

I started out after the middle of November trying to locate the necessary type and size of the capacitors I need to lower the output frequency of the TBC coils
to a simple 60 HZ . this has turned into a MAJOR search an find - time consuming effort!
this effort has not ended even yet.
the whole problem has been to find the correct sized ACV rated capacitors that are the type that can be applied as a frequency filter capacitor.
there are not as many designed for this purpose as you would think.
another problem has been when I did locate a few, those particular items are not listed as a single buy item but rather you would have to purchase eight or ten of them as a group buy - in order to get the use of just one!
when the price for the eight or ten group runs 800.00 USD to better than a
1000.00 USD that's way out of my ball park for damn sure!

today I was able to locate one or two that were single buy items but they were still big dollars at 75.00 USD to 97.00 USD. each TBC would require
three to four of these big boys.

still waiting for some more price quotes to come in also.

Later, probably much later!

Clarence

[clarence]

Info you asked for

Hello essourimed,

attached is the information you asked for.
since your country is overseas tell them it needs to be 220 vac @ 50 HZ.

Clarence

[seychelles]

JUST A NEW UTUBE TO WATCH MAYBE LEARN FROM.
https://www.youtube.com/watch?list=P...&v=-LFmmyl1JmM

[clarence]

Hi Clarence just an idea, to increase the the bifilar transtormer
it will be good if you mix epoxy with some fer rite compound and
make a mold to place the two windings in then pour in the mix..I did
that experiment with the induction cook top..That was best energy transfer i have ever experienced..Another idea is to make the bifilar with litz wire..
Easy to make your own ..Just get 10 pieces of fine magnet wire and stretch it
out and use an electric drill to spin these wires onto themselves..there you have your litz wire.

Hello seychelles,

glad to meet you.

I have not experienced any problem with energy transfer by the TESLA bifilar
coil at all. the two present TBC coils transfer approx 122+- vac and 123+- vac respectively and can be configured to give 240-246+- vac quite easily.

the only negative aspect of the coil system is the high frequency KHZ that is used by ANY oscillator type to overcome the simple fact that a plain coil whether an induction cooker type (which I have found to be totally useless)
or be it a Tesla Pancake Coil or a Tesla Bifilar Coil is merely a DEAD SHORT
as SEEN by any power input souce - EXCEPT that it be a high frequency source. try hooking your induction cooker coil circuit to anything except a light bulb and you will get a surprise.
an additional negative aspect is the LIMITED amperage component that can be supplied by ANY type oscillator to and through whatever type coil you may choose. if it isn't there to start with you simply won't have it!
at present the CAPTOR arrangement is the best means to ADD this needed electrical factor to a coil type output!

all of which brings me round-table back to my present efforts to add the needed amperage to BOTH of my TBC outputs.
my last components to reduce the KHZ to 60HZ will arrive today - and then I will be on with it!
Locating and waiting is a REAL pain in the ass!

again, glad to meet you.

respectfully,

Clarence

[seychelles]

Hi Clarence just an idea, to increase the the bifilar transtormer
it will be good if you mix epoxy with some fer rite compound and
make a mold to place the two windings in then pour in the mix..I did
that experiment with the induction cook top..That was best energy transfer i have ever experienced..Another idea is to make the bifilar with litz wire..
Easy to make your own ..Just get 10 pieces of fine magnet wire and stretch it
out and use an electric drill to spin these wires onto themselves..there you have your litz wire.

[wantomake]

System

Bromikey,
No I'm using (2) toroids same as Clarence setup with same gauge wire for the captor and almost exact picture as what Clarence posted earlier pages. Will try to post pictures asap.

My charger and inverter of course is different. I can only power small loads now but it is a start.

Sorry can't answer the question, don't understand it.
wantomake