Barbosa and Leal Devices - Info and Replication Details

[luc2010]

Thank You So Much!!

Hello Luc2010,

Here is the color for your home area - the tip of the blue arrow shows the exact location of your home. you will notice there are no exact color codes for that area so this tells me that they could not travel into that part of Africa
for some good reason (war,crime, etc, who knows).

anyway, just looking at it and judging from the other surrounding areas I would say that your area is a darker orange to a deeper red which should be pretty good.
best I could do with whats indicated.

Regards,

Clarence

Hello Clarence,

Its Very Nice To Hear From You!!

i will try only 3 ground rods and load the circuit, if the voltage geos down then i will add more ground rods? is that correct

Again Thank You So Much!!


Best Regards
luc2010

[clarence]

IFT and Oscillator

Hello BroMikey, & ALL,

I did finish my oscillator as the photo shows. I also proofed its ability with
the dual layer feritte square loop transforner ( both units have a blue LED I added as run indicator lights). I just quickly threw together the dual winding
to see the results of efforts at this stage - the input to the smaller coil was 6.32
square wave (seen as AC) @ 33.4 KHZ . the output from the larger of the dual
layer coils was 30 volts square wave (seen as AC) @ matching 33.4 KHZ.


I will be revamping the dual layer coils to give me a desired output of 120
volts AC for injecting into the middle IFT coil - NOTE that none of the IFT coils are in place at this time! all good things take time - working on it!


A note worthy point is the use of the 2N3055 transistor without a heat sink!
Simply did not need it at this point and I actually don't think it will need one for this low energy level that I will be injecting strictly for the sake of a high
KHZ signal int the IFT.

Has taken me many many hours of effort to get it all done this far and more to come I'm sure, but that's life - live it or get to hell out of the way.
another thing to note is the MINIMAL components used in the 555 oscillator
circuit I put together. effort paid off.

Need to take a day off for farm time ( and clear my head) so it's see you later time!

Respectfully,

Clarence

[luc2010]

Hello Clarence and All,

i e-mail the adresse.

my inverter:
newstar 300 watt

ground rods:
1.5 m of cooper ground rod

one more problem? to protect peoples / animals?
how to avoid the careless touch and risk of hazard electric shock!! from the gound rods? in times of raining...

Thank You so much!!

Best Regards
luc2010

[clarence]

Hello Clarence,

pro acount is needed for that?

anyway,
i start a simple experiment using only TWO ground rods, the reading on the voltage meter is the same from inverter output? no matters how the distance betwin the two groung rods?? is that a good place?

Thanks so much!

Best Regards
luc2010

Hello luc2010,

ANY e-mail account with a normal search engine will be able to access that program!

Exactly WHERE are you located in Africa? Be specific and I will find your color and post it to you.

Stay with the three foot separation advice. the three foot statement was given by Barbosa & Leal themselves! if you are getting normal voltage
values with your inverter (size unknown ? ) with only two ground rods then
your location must be good. It took me 60 ground rods to be able to do that.

best wishes.
respectfully,


Clarence

[luc2010]

Hello Luc2010, & ALL

I see its time to step in and clarify things about the magnetic anomaly pertaining to each one of you with respect to your particular location.
The Global color view for the magnetic characteristic with respect to the earth is strictly for the earths CORE !!!! it has NOTHING to do with
the EXTERIOR CRUST! the crust magnetic anomaly is a TOTALLY DIFFERENT
animal! there is NO COMPARISON between the two.
the photo I show below is from the SURFACE magnetic anomaly for AFRICA ! as you can plainly see there are many , many changes in the color shades just within a few miles of each location. that is why I have stated before that anyones success or lack of success with their B&L UNIT entirely depended on THEIR OWN LOCATION!

I will give the means for EACH of you to look up and find your own
nT (nano Tesla) value for your selves in just a minute. the map access I will state is very easy to use for COLOR value and access to your personal location - BUT it does NOT state any values for the colors at all. I Will include a separate color scale that you can use and it comes from a separate
site that I used in the past. FEAR NOT, its colors are EXACT as you will see.

First the photos:


Now the info to pull up the MAP - you will see on the top right of the page when it pulls up a block to type in YOUR COUNTRY or STATE and it will auto
display it for you. then you use your mouse to scroll it in or out to give a closer and better defined view of you location--all the while it will be showing the COLOR!!!!!!!!! It may take a while for you to get the hang of what to do -- BUT -- you are all grown ups so just humor yourselves awhile. after you have found your magnetic color then compare it to the chart that I use and have attached for you.


To get access to the map site type this in your search: ArcGIS-Magnetic anomaly map . after you have done all you need to with the map then refer back to the post and view the color chart.
lot to do but it will get you there.
Now maybe all of you can get on with business and be more at peace with your results - Hope So.

Respectfully,

Clarence

Hello Clarence,

pro acount is needed for that?

anyway,
i start a simple experiment using only TWO ground rods, the reading on the voltage meter is the same from inverter output? no matters how the distance betwin the two groung rods?? is that a good place?

Thanks so much!

Best Regards
luc2010

[luc2010]

seems not impossible task!

Hello Luc2010,

As I said in the E-mail that your tip of Africa with respect to the Global magnetic Anomaly shows heavy Blue which should mean bad for for a B&L
type unit. mine is in the minus nT value range. it shows on the US map to be about -30 nT tesla value which is still piss poor and really doesn't accomplish any thing either.
Who knows - keep after it until you find out for certainty, youve come this far.

Best wishes anyway!

@ALL

hope to have my oscillator completed by the end of week. was having problems because of cheapo trash made 555IC chips and went through several before found out the problem. have ordered the QUALITY brand and will be in Friday. seems like always something to screw up the works.
Oh well, back after it as I can.

respectfuly,

Clarence

Hello Clarence,

Well,
Thats the same blue color that we can see in B&L location? right

and thats why theiy ask for a good grounding system!!!!! BUT it works for B&L??
then why it cant work for us?....i mean, ITs not an eazy task to do as we can all see and hear!!
Yes, it make sens to me!!!

Later!

Thanks and Regards
luc2010

[clarence]

Hello,
@All

HOPE, now that I have everything exactly as Mr Clarence recommand?
to power the unit?
i need to charge my battery or find another one, as you know we cant power this unit from the mains!! the input must be only from battery and inverter!!


back to work!

Thanks and Regards
luc2010

Hello Luc2010,

As I said in the E-mail that your tip of Africa with respect to the Global magnetic Anomaly shows heavy Blue which should mean bad for for a B&L
type unit. mine is in the minus nT value range. it shows on the US map to be about -30 nT tesla value which is still piss poor and really doesn't accomplish any thing either.
Who knows - keep after it until you find out for certainty, youve come this far.

Best wishes anyway!

@ALL

hope to have my oscillator completed by the end of week. was having problems because of cheapo trash made 555IC chips and went through several before found out the problem. have ordered the QUALITY brand and will be in Friday. seems like always something to screw up the works.
Oh well, back after it as I can.

respectfuly,

Clarence

[luc2010]

Hello,
@All

HOPE, now that I have everything exactly as Mr Clarence recommand?
to power the unit?
i need to charge my battery or find another one, as you know we cant power this unit from the mains!! the input must be only from battery and inverter!!


back to work!

Thanks and Regards
luc2010

[j_f_d]

It cant be right. Mesured is around 50microTesla. And world magnetic map (that is not precise enouh) shows that region is 50 000 nT so that is the same 50uT.
https://upload.wikimedia.org/wikiped...etic_field.jpg

There are bumps to 90microT and deeps to 20microT when i drive around.
So that is around 50 000 nT and your map says 140?

[wantomake]

Mitja,
From what I seen on NOAA website your area is 142nT.

wantomake

[wantomake]

Question for all, that made successful replication.
I cannot get geo-magnetic map for my country for now.
Almost all tablets and smartphones have magnetometers built in. I tried with iPad and iPhone. There are free 3d magnetometer apps.

Is there a possibility that you measure your magnetic flux around your grid field?
I have around 50microTesla around my house. Is that enough?

Thanks and best regards to all!
Mitja

Mitja,
What country are you from? I may find it for you. Please give north,south, etc, area you live in.

The nT in my area is 200-400(not sure how the scale reads). I also took readings with my iPhone 4s using same app and got 60-80 nT around my ground grid.

Also when placing the cell phone on the ground above an copper coated rod got 160-180 nT. But doing same over iron(rebarb steel) rods it read 300-500 nT. I know a neodymium magnet will read 14,000 gauss. But are the iron rods getting magnetized in the ground?? Not sure if this helps you or not. But the geomagnetic scale where I live is medium to high.

Hope you the best. Check for availability of copper coated grounding rods, large awg wire, batteries(I use lead acid), inverter, and such before starting your replication. Just to save you money and time.

I've had some success, but need more grid rods,
wantomake

[j_f_d]

Measurement of magnetic flux

Question for all, that made successful replication.
I cannot get geo-magnetic map for my country for now.
Almost all tablets and smartphones have magnetometers built in. I tried with iPad and iPhone. There are free 3d magnetometer apps.

Is there a possibility that you measure your magnetic flux around your grid field?
I have around 50microTesla around my house. Is that enough?

Thanks and best regards to all!
Mitja

[wantomake]

Test #46

To All,
Quick update.

Purchased and built the single toroid setup with #2 awg wire because Lowes was out of the #1. Still heats up to 120F. Still has very slow voltage drop. About a 10th volt per hour. Built exact as Clarence pictured some post back. Only can power shop lights, small floor fan, and charger.

With the addition of more grounding rods the amount of useable power will increase. The purchase will take time so will post as this happens.

wantomake

[wantomake]

A little success

Thanks Clarence,
The encouraging words do help.

I went some pages back to study the GDT neon bulb placement in the circuit. The first test run (one toroid) with GDT, made the battery bank actually start charging. Thats with load of shop lights and charger. But again expectantly the captor heated up.

So i tried the two toroid setup to just know. The heat did stop but voltage drop on the battery bank was slowed greatly. About 10x.

So to Lowes for the #1 awg and connectors. The rods i'll add as I go. Cause the geomagnetic colors are high in this region. This little success with (1) input rod, and (4) output rods.

I just needed the GDT to confirm this idea works before using more resources.

Will keep you and All posted as I can,
wantomake

[clarence]

Hey Clarence and All,
Sorry to hear that Luc. Hope you figure it out.

I connected the old #4 awg captor to the single toroid just to get some idea of captor amps. Got 145 amps with clamp on meter. But started heating up after few minutes to 135f +. Was able to run shop lights and charger set at 2.0 amps charge.

Thats the most amps so far. But battery bank lost 10th of a volt per (2) minutes.

The local Lowes has #1 awg copper not tinned for $2.28 a foot. So for around $20 for 7' wire and split bolt connector.

So may need to make that purchase,
wantomake

Hello wantomake,

sounds good so far. I believe the heating is causing some of the voltage drop
but you will find out with the larger wire. as the wire size goes up the heat issue tends to disappear. the slow batt drop should decrease slightly also. I don't know about your location so I can't say whether another rod or two
would be of any benefit or not - you will know as you go.

rods in my location really ended up being a joke (almost). never fear about any captor setup , they work if built correctly. I never managed to cure the
slow voltage drop even with the in line charger. just a case of lack of ground support for the Captor to work at it's best is the story. no more , no less.

in the end that is why i went to another voltage method to provide enough voltage to overcome the lack of ground support AND DID FIND IT with the Tesla TPC and TBC coils working together in harmony. but the voltage I produced, even though it was MORE than sufficient, I couldn't use because it was HIGH FREQUENCY power. only thing it could be used on was bulbs
and they burnt out after a while. CFLs would crash in about 6 seconds. and kill-a watt meters went to bye-bye instantly. high frequency just sucks.

However, even that obstacle I have found a way to overcome. that is what I have been working on for the last several months. hopefully by the end of May I will have everything in order and make some runs for results.
will see.
thanks for listening wantomake. hopefully your last efforts will give success.

Respectfully,

Clarence