Barbosa and Leal Devices - Info and Replication Details

[BroMikey]

Hello Clarence

Good testing, only a real rigger can appreciate a high amp handling
power switch made at home to swap out or reverse charge and run
system batteries.

Ions love to charge up going one way so this is a conservative approach.

The captor winding changes up to 64 turns opposes a transformer
winding ratio of far less potential difference. As any transformers turn
ration drops so does the voltage and so does the amps in most cases.

This is what we experiment for, we are looking for that tuning as others
have put it. As an example when John Bedini got me doing his ENERGIZERS
in the early 2000's, I began to look at batteries much more closely so let
me explain.

Not to go on for long yet look at the 12v battery. If my battery is being
tuned to a circuit for charging, that battery must have a certain voltage
above the 15v target so amps will move.

This is my best way of talking, somewhere between old school and one leg
up on something new at school. Many wave forms can show low amps as
compared to a normal charger that charge the battery better, why?

Because the voltage is somewhere between 30v and 100v with most of
the wave self adjusting to work with the battery to over come

PLATE RESISTANCE

Once plate resistance is looked at properly you look for ways to charge
a battery first most efficient and in some cases more than 100 percent.
Of course this is beyond the scope of our thread but if we charge and
discharge our batteries at the same time, the circuits appear obstinate
maybe a 20 percent charge conversion efficiency.

When conflict exists in the system instability rules and we are faced with
and endless set of anomalous patterns that throw off our investigation.
This is why John B. took us to the beginning of running power in and out
of batteries.

Now that you have eliminated this losing battle with ions you can get
a better picture in the developing investigation without kicking batteries
throwing your data off.

On one final note, keep looking for your desired effect and know this
that many other added changes will improve what you have also.

Together we will make experimenting great again.

[clarence]

BRO MIKEY,

Nicely done Sir!

For all of BlunderDog's intelligence he still is not smart enough to
understand how forum posting and deleting works on this site.
Seems he can't understand that posts can only be deleted BY THE ONE WHO MADE THEM or by the forum Administrator/Moderator !!!!
Hopefully he will see information I have stated and bless us all by deleting them himself as he said he was willing for this to happen.
Then he can return to his own thread and remain there. HOPE SO!

Thank you again BRO,

Clarence

Hello BRO,

Finally finished and ran the system with the improvements of the Supercap banks as the lead receiver of the charge voltage from the Batt charger prior to the battery itself.

The draw on the battery this time was 10.6 amps (a lot I believe).
used my 3000 watt Aims inverter - others were too beat up to use any more.
the toroid didn't perform at all this time - It's amp was 112.9-113 amps.
It remained the same reading all the time.
Last time I had 8 #10 AWG turns around the mid of the toroid loop
and it showed it was furnishing amperage by induction to those eight turns.
this time I had stepped it up to 64 wraps and it didn't give up anything.
Evidently more is not better. Will drop to just 4 wraps over the weekend
and see what happens going with less.

This time I had two batteries being charged at the same by the Xantrix charger (specs say it can do three at a time !) One was used for the test
and the other was idle while being charged ( not connected to anything
except it's own supercap parallel to battery leads from charger.
Took only about 4 minutes to charge it from 12.2 to 14.3 ready to go.

The charger and a 100 watt CFL were self looped back to the charging of both separate batteries.
The run was shorter this time because it had no help from the large wire toroid unit.
Still the run was long enough coupled with the fast enough charge of the idle battery to convince me that a 24/7 hour option is possible - all at 60 Hz.
To accomplish that it would just be necessary to switch the idle battery into service and the being used battery out of service. the out of service battery still has its own incoming charge since it is already connected to the charging circuit and would only take about 4 minutes to be ready to go again.
I have located a Make..then Brake battery switch that is made and designed for just this purpose to switch batteries UNDERLOAD so as not to interrupt service and without damage to normal components the inverter is powering.

The switch I will order will be in by late next week and I will build that
system to make use of it.

Be mindful that this is a MANUAL switch. It will have to be updated with a

timer/servo control to make it automatic for the end user.

Still lots to do but that's better than sitting on a dead ass twiddling thumbs.
No jpg pics at this time - nothing worth the effort.

thanks for listening BRO,


Clarence

[JS5]

Good riddens

Hope he is gone now, then we can follow this thread without the mostly duplicated blabber in-between.

My one toroid Clarence-replicated captor loop survived switch-on. Will start testing with loads this week.

Thank you for the email details Clarence sir!

God bless!

[BroMikey]

The two sets of steel grounding rods must be
close enough to electrostatically “feel” each other to register a
voltage difference between them. And there must be a strong
enough geomagnetic field flowing between them to “blow out” a
ny chance for arcing to occur which could neutralize their voltage
difference. A dry soil will also help in this regard.

But it is their difference in mass, alone, which conveys this
voltage difference between them acquired, not from the Earth,
but from their magneto-motive reactions to the oscillations built
up between them originating from within the circuit of Barbosa
and Leal. It is this circuit which is the source of oscillations
throughout its entire design manifesting in all of its parts not
the least of which lies between these two sets of grounding
rods.

Geomagnetism merely prevents obliteration of voltage between
these two sets of rods. It does not supply them anything other
than immunity from decay.

An analogy exists from within Richard Hackenberger's last edition of
the EV Gray motor according to its assessment by Mark McKay.

Compressed air (analogous to the flow of geomagnetism) was forced
through the interior of the EV Gray motor to prevent arcing between
the aluminum chassis (lined on its interior surface with Teflon) and
the aluminum supports underneath the rotor/stator coils. These
aluminum supports were insulated from their immediate surroundings
so as to become dielectrically isolated from all other parts of the motor (including the chassis whose voltage potential just happened to be in opposition to these inner support pieces). Yet, it was the electrostatic
field surrounding the rotor and stator coils which fed the polarizing
charge built up among these inner supports and the chassis of the
motor so long as sufficient air kept blowing in through this motor's
interior to prevent arcing and an elimination of electrostatic charge
existing between the chassis and these aluminum supports. This
electrostatic field contributed to the motor's overunity performance
as an oscillatory response to this motor's operation. This response did
not go unnoticed by the motor's output despite a lack of direct
connection between these two “floating” capacitor plates and the
circuitry of the motor.

The Electric Keeper of B&L has to be driven by something. The
contribution of voltage supplied by the AC Sinewave Inverter is one
source. But the Earth is not the other. The Earth merely provides
isolation so that an electrostatic buildup can occur among the two
sets of grounding rods: isolation via a dry soil, but most importantly
isolation between two differing masses of ferromagnetizable material possessing a potential difference of magneto-motive force (not to be confused with electro-motive force although this latter will be the
end result).

Tesla used magnetic fields to quench a spark gap. The Earth, here,
does the same.

Now that I've contributed my assessment, you may delete them all. Good-bye!

Good Bye to you also, but before we part let me suggest something to
you if I may. It is bad manners to steal documents just because you
are able and then joke about it in an insulting way to the one you took
them from, knowing it would be against his will in an effort to belittle.

Further you are not sorry but think it is a cute display of your dazzling
abilities just like this post where we can all see how smart you must be
being such a deep thinker.

We have no short supply of super intellect here only those who have
the time to do the work. Your good bye emotional out burst as a way
to turn your status to victim is nothing new either.

We are all glad you are a super thinker and wish you well tho another
long post on theoretical jargon is nothing more than rubble to the
working man.

Good Day.

[BroMikey]

Hello BRO,

regarding the self loop system I discussed by E - which includes
my FIRST use of the Large toroid for it's ability to transfer amperage
by induction to wire coils wrapped around it's own 5 turn loop -
I will make a post some time next Tuesday maybe Wednesday
(depending on how long it takes to make the mentioned improvements)
- I will use the forum jpg attachment method for clarity.
No more photos for certain.

Kindest Regards Bro,

Clarence

Hello Clarence

Exciting to hear from you and to watch you experiment (Stumbling process)
till you hit a homerun. At-ta-Boy In your message to me
privately I think i know exactly what you are doing with the changes
and soon I will be sure when you post your final.

Your setup is so over the top, looks industrial, components are all
high quality. There is always another improvement to be had.

Looking forward.

[clarence]

Self looped system with large toroid build

Respectfully please do not post your personal messages on this thread. Such as car reviews etc.

If you are going to address the thread owner (CLARENCE) do so by
saying excuse me and do not change the topic.

This thread is about building designs of the B&L captor and getting
yours working, not about hypothetical external operating systems
of endless schemes.

A moderator will be asked to delete your comments in this thread if
you continue and that is more work for them.

You have your own thread so by all means use that one for your
personal topics.

Thank you and God Bless.

Michael Rowland (Central Kansas USA)

Hello BRO,

regarding the self loop system I discussed by E - which includes my FIRST use of the Large toroid for it's ability to transfer amperage by induction to wire coils wrapped around it's own 5 turn loop - I will make a post some time next Tuesday maybe Wednesday (depending on how long it takes to make the mentioned improvements) - I will use the forum jpg attachment method for clarity. No more photos for certain.

Kindest Regards Bro,

Clarence

[JS5]

Thank you Clarence. I was mistaken, all those photos are showing up now in previous posts. I will PM for that other info. Won't waste your time with PM's on silly stuff.

Much appreciated!

[clarence]

Give me a pm to get you started

Hi Clarence and BroMikey,

It took a month to get registered here, but eventually made it here.

I have been studying your posts from page one through to the last page after watching almost each and every Youtube video. (Ignoring all the clatter of course).

After experimenting with a Pulsed Magnet Motor design (successfully self-driven/self-charging, not OU yet but with potential), and self-resonant oscillators that proved to me COP1+, I decided to search for a high power solution that might fall within my limited capabilities. I am electronics qualified, but mains systems and high-frequency HV designs is not my expertise. although I understand the basics of course.

I have my two 230V, 300VA 160 deg wound grain-orientated silicone steel cores now. Had them manufactured in South Africa for a mere equivalent of $26 ea. That was before I read about the geomagnetic strength issue. My area is lousy as well. So I decided to follow the route of a single Toroid solution that I will first get going from mains supply, Being in a country where this most corrupt Government is openly stealing billions from us, I don't care too much for now about the so called ground loop issues, just want to get the thing doing the job and will then look for solutions to run it independent from the grid. I pray for Clarence to find a solution to replace the ground rods. Please keep on doing and posting sir!

Unfortunately all the pictures of that one Toroid system have been removed, is there any way I can get hold of the pictures Clarence posted on this forum?

Clarence: could I PM bug you for that info on the treatment of cancer you mentioned somewhere in this forum? Know many people who could benefit from that as I share your opinion about the traditional medical approach, lost several family members and friends who went that route.

Anyway, thanks for all your work and R&D burning candles to help us all.

All the best!

Hello JS5,

YOU can give me a PM and I would receive and answer it.
Am not to hot towards constant PMs but a first time from any member is welcome Sir! I will try a jpg thumbnail now of the Large toroid build that gives 106.9 amps AC.

Regards,

Clarence

[JS5]

Hi Clarence and BroMikey,

It took a month to get registered here, but eventually made it here.

I have been studying your posts from page one through to the last page after watching almost each and every Youtube video. (Ignoring all the clatter of course).

After experimenting with a Pulsed Magnet Motor design (successfully self-driven/self-charging, not OU yet but with potential), and self-resonant oscillators that proved to me COP1+, I decided to search for a high power solution that might fall within my limited capabilities. I am electronics qualified, but mains systems and high-frequency HV designs is not my expertise. although I understand the basics of course.

I have my two 230V, 300VA 160 deg wound grain-orientated silicone steel cores now. Had them manufactured in South Africa for a mere equivalent of $26 ea. That was before I read about the geomagnetic strength issue. My area is lousy as well. So I decided to follow the route of a single Toroid solution that I will first get going from mains supply, Being in a country where this most corrupt Government is openly stealing billions from us, I don't care too much for now about the so called ground loop issues, just want to get the thing doing the job and will then look for solutions to run it independent from the grid. I pray for Clarence to find a solution to replace the ground rods. Please keep on doing and posting sir!

Unfortunately all the pictures of that one Toroid system have been removed, is there any way I can get hold of the pictures Clarence posted on this forum?

Clarence: could I PM bug you for that info on the treatment of cancer you mentioned somewhere in this forum? Know many people who could benefit from that as I share your opinion about the traditional medical approach, lost several family members and friends who went that route.

Anyway, thanks for all your work and R&D burning candles to help us all.

All the best!

[BroMikey]

I bought my classic for two reasons: I wanted
to contribute to what has proven itself to be the best solution for going
green despite the inconvenience of driving an electric car in today's world
of politically correct bondage to the gas pump.

Respectfully please do not post your personal messages on this thread. Such as car reviews etc.

If you are going to address the thread owner (CLARENCE) do so by
saying excuse me and do not change the topic.

This thread is about building designs of the B&L captor and getting
yours working, not about hypothetical external operating systems
of endless schemes.

A moderator will be asked to delete your comments in this thread if
you continue and that is more work for them.

You have your own thread so by all means use that one for your
personal topics.

Thank you and God Bless.

Michael Rowland (Central Kansas USA)

[BroMikey]

Hello BRO,

No sleep here Bro!
Thanks for the comments and insight and support as well.You are correct
in saying there are many excellent leaders here and they have continually proven themselves so in the same manner.

Thanks Again Bro,
Best Wishes,

Clarence

Thanks Clarence I knew you like that, also the BOYBLUNDER?

The BOY BLUNDER has deleted his book math copy and paste so
he doesn't like who he really is. Now he has added something else.

He is a tricky fox.

Next it will be all my fault because of his embarrassing thought process
and even tho he and others would love to call me everything but a
white boy, I am the one who is the bad man attacking the poor defenseless.

What a world of men who are spiritually castrated.

[BroMikey]

Hello BRO,

Watch out - BLUNDERDOG ,s on the loose again!

You heard of the comedy show WONDERDOG
I call this comedian BLUNDERDOG!! HA! HA!

Regards,

Clarence

Egg-Zactly this gentlemen is front and center on your thread acting as
if he is going to explain everything mathematically but those are easy
to find copy and paste text out of books made by the shadow Gov who
fly around without gravity and make school books that use endless
formula and withhold the true knowledge.

The boy blunder is the average college boy who never smelled any of
the real coffee. It is one thing to get schooling, that is fine yet
somewhere, you would think, reality would kick in. NOPE. Just the
endless parroting of "TEACHER TOED ME" like some 3 fingered brain
dead zombie who was programmed NOT to think through the simple
experiment.

Your posts need not be cluttered or speckled about with school boy
rhetoric that isn't even used in real world science. I have seen children
do much better than these big boys coming out of the gov crusher.

Your post gives me the chance to explain how it feel from our end.

It's not just "BLUNDER"

From here it looks like so many people can not follow simple directions
however in many cases I have learned that their obstinate way turns out
to be a condition picked up from their professors,

"Here are all the answers say this and you will pass"

Most of those caught up in big business power producing plants have
been duped to believe they are up with Telsa as they clean all of the
beautiful copper/brass lugs off and like pets right out of schools look
for that special stroking by their superiors who herd them around under
this fraudulent mind warp.

I agree, this is what I deem true "Comedy" almost as pathetic as the new
SNL hit job mind freeze pulled over the public mud guppies

It's the best they can do.

I don't mean to take up to much time on the subject on all these look
alike 'ARM CHAIR COMMANDERS" who should have known that schooling
was only a basic entry level while they all seem to reject anyone who
does the experiment. They all say the same things, "SHOW ME MATH"

IT WON"T WORK BY THE BOOK" "You are a FE circus clown" on and on
we go showing pure disdain for the direction that the experiment takes us
and implementing their own obsolete dogma as cover for their $50,000
school bill that they are still paying at age 45 years.

Most of the highly educate all fall into this bracket so look for another

Anything you offer them out of kindness is looked at as incorrect even
before any evidence is presented.

We are blessed here with leaders who can see both sides and they are
the real minds. I use to think that all that glitters is gold
like the big money and the prestigious position of power in the tech
industry. It is all meant to keep us traveling down a path opposite to
reality using peer pressure as a "Whipping Post"

I hope I didn't put anybody to sleep.

.

[clarence]

Don't worry about the weirdo's they have to show their ability to
screw over or they won't have a life. I know he wants to cloud the issue
so he can show what a neon does.

Same ole burning watts to ground genius

The setup is coming along great, can't wait to hear more.

Hello BRO,

Thanks again Bro.
Have something new to try next couple of days. It should give me an indication of what is or is not next.
Will give you an E on that thou about mid week.

Regards,

Clarence

[BroMikey]

Hello Bro .

Yeah , thats right !

Also below your post You will find BLUNDER DOG is back with
usual ASS Hole ****
Thinks hes intelligent - just a stinking TURD!
The silly SOB doesn't understand I NEVER used a neon bulb open
ended or otherwise. DUMB ASS!
OH WELL!!!!

Regards,

Clarence

Don't worry about the weirdo's they have to show their ability to
screw over or they won't have a life. I know he wants to cloud the issue
so he can show what a neon does.

Same ole burning watts to ground genius

The setup is coming along great, can't wait to hear more.

[BroMikey]

Hello BRO,

Made new run on PV.

3 panel no exterior light.
12 v batt .
12.6 v begin.
11.6 v end
1000 watt inverter with 75 watt load.
7 hour run.
Working towards powering 106.9 amp large toroid 24/7.
To be continued.

Regards,

Clarence

Yeah this sounds good. I am looking forward to even better results, this
one is good. This shows a principle that is working and from what i gather
is a way to transfer power without interrupting a dipole? If this is right
then you just got 75 watts free for 7hrs?

I think this is right. I know you have other processes going that have
ranged from the captor to the Tesla pancake system.

I know you will fill us in when you can get more of what you want.

Very exciting progress in the right direction.:thumbsup: