Barbosa and Leal Devices - Info and Replication Details

[clarence]

Size of inverter counts

From this, it sounds like much less net power would be available when using a battery/inverter setup not connected to the grid?

digits10

Its the size of the inverter that counts,
AND you have to bear in mind that the current/amperage being consumed is not really sensed by the inverter just like the same thing that happens with a mains system.

The MOST important thing for a battery Inverter system would be whether or not it can pull in enough energy to power a smart charger and keep its batteries at peak voltage.

Best to you Sir!

Clarence

[digits10]

Next

Clarence,
Thanks for the reply. I decided to pick up a hammer drill attachment - hopefully that will make the ground rod project easier!

You gonna fire up your inverter & battery bank to see what happens? I'm still probably 2 weeks out to get to that point.

[wantomake]

Goal

Clarence,
Thanks for the reply. I decided to pick up a hammer drill attachment - hopefully that will make the ground rod project easier!

You gonna fire up your inverter & battery bank to see what happens? I'm still probably 2 weeks out to get to that point.

My main goal has been to power this setup with an inverter/battery with charger that would be totally self powered. But that's after my ground grid is in place. So I'm on snails pace now and hate it. The patent said B&L jumped their system off with mains then switch over to system powering itself. I think maybe with inverter/battery.
wantomake

[BroMikey]

I spent time doing the math and it seems that for the said 25 amp load
total 75% comes through the mains Line supply - the OTHER 25% comes THROUGH THE GROUND RETURN.

Hey Clarence

This statement will be attacked by critics thinking you mean 75%
of your power was coming from the mains off the grid. So please
let us all know what MAINS that 75% of the power is coming
from. Plz clarify that the mains you referred to have nothing to
do with the power company mains.

Possible change your wording to say "Power Bus" a separate designation
other than "Supply Line Mains", terms power companies use to talk
about THEIR grid.

Your mains and THEIR mains are not the same thing to you but others
may become confused.

Just watching your back.

PS The above statement could be easily misinterpreted and get
people thinking that your calculations show that you made a mistake
about getting the energy from the environment. Something that has
already happened once before.

Everyone knows that your experiment derives energy from the ground
rods so it looks like you might be saying that only 25%..................?



Thank you for your hard work of love and support to the sheepeople.

[clarence]

Thanks

Hey Clarence

This statement will be attacked by critics thinking you mean 75%
of your power was coming from the mains off the grid. So please
let us all know what MAINS that 75% of the power is coming
from. Plz clarify that the mains you referred to have nothing to
do with the power company mains.

Possible change your wording to say "Power Bus" a separate designation
other than "Supply Line Mains", terms power companies use to talk
about THEIR grid.

Your mains and THEIR mains are not the same thing to you but others
may become confused.

Just watching your back.

PS The above statement could be easily misinterpreted and get
people thinking that your calculations show that you made a mistake
about getting the energy from the environment. Something that has
already happened once before.

Everyone knows that your experiment derives energy from the ground
rods so it looks like you might be saying that only 25%..................?



Thank you for your hard work of love and support to the sheepeople.

BroMikey,

Thanks for the heads up!
Yeah, the only thing the Utility grid powers is the Two toroids, and that only amounts to .07 Amps. Every thing else does come from the ground.
After all , that's what their whole devise is all about and how they managed to get it done.

Hows's things going on your end? I have looked in at times on you work and photos . All of that seems Busy Busy Busy!

There has been a lot of posts and look ins from many members this last week ,That's for sure.

Thanks again for the advice BRO!
That I will keep in front of my noodle for certain!

Best wishes on your end BRO!

Clarence

[Hotdog]

Schematic

For those of us who have spent a career thinking graphically, here is a simple diagram of what I think Clarence's pictures show. Please advise if there is an error and I will redo it.

[clarence]

Toroid part number and ordering information

Hello GoToLuc,

You had asked for the Toroid Part number and ordering information.

In the thumbnail attachment youwill see the old invoice fro Bridgeport Magnetics Company. Also you will see an image of what they look like.

You should be able to get a hold of them and order what you need from this information.

Hopes this helps Sir!

Clarence

[gotoluc]

Thanks Clarence for taking the time to post your Toroid details

Kind regards and thanks for sharing

Luc

[clarence]

Ordering

Thanks Clarence for taking the time to post your Toroid details

Kind regards and thanks for sharing

Luc

Luc,

When ordering be sure to tell them that it will be for 220volt 50 Hz.
I believe that is right for your area if I remember right (hopefully).

Clarence

[FRANKLIN]

Gas discharge tube

For those of us who have spent a career thing graphically, here is a simple diagram of what I think Clarence's pictures show. Please advise if there is an error and I will redo it.

Hello
I saw your schematic.
Could you tell me more details about the gas discharge tube.
it looks like it is a SPRAK-GAP?
If I compare this schematic with the picture from clarence, it is the very small piece that is between the negative and the positive?

thanks

franklin

[Hotdog]

Gas Discharge Tube

Franklin,

That is the symbol for a spark gap. My component library did not have a real gas discharge tube. They are essentially the same by providing an arc-over when a certain voltage level is reached. If I remember correctly, Clarence said his is 150 volts, Mouser part number B88069X2840S102. In his picture it is in the upper left corner on a two-terminal block.

[BroMikey]

Good Deal

BroMikey,

Thanks for the heads up!
Yeah, the only thing the Utility grid powers is the Two toroids...........

Hows's things going on your end?

I see everyone is getting excited and chiming in. It has been a long
wait but worth it after all. Yes my work is coming along slow because
I do not have much time each day to work on it. However the winding
table is finished.

Now back to your sweet setup. I see one schematic recently posted
and wondered if that is the entire circuit. Since I have already posted
earlier drawing that were inaccurate, perhaps I should update the
drawing.


It is no hurry, just whatever you want is fine. I see your wrap numbers
have changed slightly on the heavy electron captor amp section.

I am thrilled to see your victory, just get in there and do. That is your
motto. You are going to have folks clamoring from here to
christmas to test the waters now.

Be ready for anything

[level]

Hello Clarence. How are things? Haven't been following very closely for quite some time, but as I have mentioned in the past, do you get the same results when you are not connected to the mains, but power it from batteries and an inverter instead? I think this is an important point that should be made clear before other people go spending a bunch of money trying to build it.

From what I understood, you say the power meter shows it is only using about 8 Watts from the mains (0.07A current draw), so if your setup really is over unity it should be able to power microwaves etc. using just a battery and low power inverter to power it. If powering from the inverter doesn't work the same at all as when you are powering from the mains, then for certain your extra power is coming from the mains, and is not real free energy. So, to make it clear for everyone else here, when you use only a battery and inverter to power it (no mains connection at all, anywhere), does your power meter still show just 0.07A draw from the inverter output while powering your microwave, or is the current draw from the inverter much higher when using the inverter? Your best bet to really be sure what is going on would be to measure the current draw from the 12V battery using a clamp on current meter over a battery wire (set to measure DC current), as those portable power meters can sometimes be fooled depending how you hook things up.

[flaviop]

ups for power unit

Hello Clarence, Congratulations on your work. I would like to know about what you think of using an online double conversion ups to power the system?
thanks.
flavio pereira

[BroMikey]

Hello Clarence. How are things? Haven't been following very closely for quite some time, but as I have mentioned in the past, do you get the same results when you are not connected to the mains, but power it from batteries and an inverter instead? I think this is an important point that should be made clear before other people go spending a bunch of money trying to build it.

From what I understood, you say the power meter shows it is only using about 8 Watts from the mains (0.07A current draw), so if your setup really is over unity it should be able to power microwaves etc. using just a battery and low power inverter to power it. If powering from the inverter doesn't work the same at all as when you are powering from the mains, then for certain your extra power is coming from the mains, and is not real free energy. So, to make it clear for everyone else here, when you use only a battery and inverter to power it (no mains connection at all, anywhere), does your power meter still show just 0.07A draw from the inverter output while powering your microwave, or is the current draw from the inverter much higher when using the inverter? Your best bet to really be sure what is going on would be to measure the current draw from the 12V battery using a clamp on current meter over a battery wire (set to measure DC current), as those portable power meters can sometimes be fooled depending how you hook things up.

Hello Level

I think everyone has the same questions, all over again and from previous
posting it looks like wantomake is eventually going to do that test but
right now Clarence and a few others are spending time with the newest
alterations. Now everyone wants to know if the energy is coming from the
grid or our grid, from the mains or our mains, very confusing in and of itself
to use the same terms for THEIR grid and our GRID.

But like you say we don't have our grid set up yet.

From what I gather Clarence had thought for about 1 year he was not
getting any power from the utility company pole transformer, then he
measured something and I don't know how he arrived at the deduction
but said he basically had failed.

He did not fail completely, just a temporary set back. Now this new setup
seems to be nearly same as the old setup as far as I can tell so my question
would be, what test was made that change Clarence mind?

What test was it that Clarence made that caused him to think his first
setup was drawing power from the grid and what test was it that Clarence
made that showed him he was no longer getting power from the
utility company.

You see I don't know what test he made, you will have to ask him. It is
a valid question and I hope Clarence is up for it. We better let him do
more verification and I am sure he will clarify his reasoning for now
thinking he has something different than he had last year.

Believe or believe not don't mean zhit, we need more to go on than
what we have before the money is spent on all of these boxes.

Now are you happy with my reasoning LEVEL?

From the patent information the utility grid is required to make the unit
function? I am not sure, but if that is the case what is the reasoning
behind it? Most would say it is because some back flowing current is
being harvested in such a way that no meters can read it.

But Clarence was honest enough to own up to the fact that his first
setup was drawing power from the utility company transformer after he
defended that is was not for a year.

The question should be "what test did Clarence use that changed his
mind" helping him to know one way or another. I have read all of the
posts and I must confess it has been a long slow mess of tiring
changes from one experiment to another.

Clarence is a fighter and that is why he will not fail in the end.

PS I told you to be ready for anything Clarence and Level is back.