My Asymmetric Electrodynamic Machines

[Midaztouch]

The core architectural structure of this motor generator seems to be flawless. I've been back and forth and in 3D with the magnetic force interactions inside the core. I've tried my best to find a flaw but I can't. It seems to me to be perfect...

The commutators are open for discussion. My thing is that the comms create a "natural occurring pulse". The DC output will flow out smooth and plentiful, easy to control..... Of course the JS Monster pulser will put system in hyper drive, like the whole system on steroids, growth hormones and a lot of caffeine! The DC current will be coming out like a river after a major rain storm

Does anyone see any weak points that I can't see? Thank you

Keep it Clean and Green
Midaz

[Ufopolitics]

God Bless You...

It's Erfinder, it has a meaning, I don't abbreviate it.

My response to that individual wasn't meant as an insult to you, it was a reaction that he should have expected, period, he insulted me. I don't post on your thread...I don't make comments, or offer suggestions...I don't provoke you or your following, I leave you people alone. He said some fresh crap, begging for my attention. Don't call me out if you don't want me here.

My opinion of your work hasn't changed, regarding this new disclosure, my opinion is negative, and as such won't be viewed fairly, so I'll just keep the opinion to myself.

Regards

God Bless You Erfinder!

Namaste

[erfinder]

Hello Er,

C'mon man...you could do much better than just that comment...

You are a smart guy...would like to hear your opinion on this...even if it is a negative one.

Regards

Ufopolitics

It's Erfinder, it has a meaning, I don't abbreviate it.

My response to that individual wasn't meant as an insult to you, it was a reaction that he should have expected, period, he insulted me. I don't post on your thread...I don't make comments, or offer suggestions...I don't provoke you or your following, I leave you people alone. He said some fresh crap, begging for my attention. Don't call me out if you don't want me here.

My opinion of your work hasn't changed, regarding this new disclosure, my opinion is negative, and as such won't be viewed fairly, so I'll just keep the opinion to myself.

Regards

[Ufopolitics]

C'mon...Er!

Think again....blind follower......

Hello Er,

C'mon man...you could do much better than just that comment...

You are a smart guy...would like to hear your opinion on this...even if it is a negative one.

Regards

Ufopolitics

[erfinder]

Another amazing demo UFO
I remember early on when some rude people were calling you the guru and the rest of us your blind followers. I am thinking that sooner or later they will show back up wanting to study at the feet of the master.

Think again....blind follower......

[Zardox]

Amazing

Another amazing demo UFO
I remember early on when some rude people were calling you the guru and the rest of us your blind followers. I am thinking that sooner or later they will show back up wanting to study at the feet of the master.

[RandyFL]

Soft Iron

23 May 14 / 24:21:00
Hello All:
Does anybody know where to get soft iron from...
In what shape or form and how much...
Trying to finish some other project so I can start asymmetrical project.

All the best
RandyFL

[Ufopolitics]

Dual Supercaps Crossfiring Machine Coils...

Hello to All,


[IMG][/IMG]

Above I am showing a completely new and different way to feed my Machines...yes, we could also feed them like that with side battery Banks as well as caps...but on the following video you will observe how well the Super-caps get charged with this little motor...

SUPER CAPS CROSSFIRE (PART 2)

On the video I explain clearly on my "hand sketch" how this works...the final part is that Caps get charged by "half" charge from battery/L1 and the other half enters through our collapsing coils (L2) reversed currents...

We only test here C1 & C2 as Side Supercap Banks...No C3 shown here, like on First Video (Buffer Cap)...This Buffer Cap keeps bouncing charges back and forth between this Two Crossfire ends...and when I disconnect batteries...it starts "filling up" from both ends...they start a "Communication Network" between Parallel and Series Resonance...and we will put all this in schematics so we could discuss the best way to keep harmonics through electronics control, in a more accurate fashion...


I wanted to show here, mainly, the Generating Capacity of such small Five Pole All North Asymmetric Machine...to the point Motor "feeds back" itself reaching over 13,000 RPM's on a power it generated, using only Milli volts.


Once I complete this 3 videos, I will move on to "Bigger Toys"...I miss them...besides this little machine is limited by the number of poles/coils...and that reflects on the speed to regenerate and acceleration properties...

The "Effect" I am trying to achieve now...is to observe the same increase on Supercaps as We have seen in Battery before...while acceleration increases also...but it is not a simple deal guys...it occurs at specific speeds...and specific voltage levels from THREE POINTS at Caps...or decay will prevail...so, lots of development...and lot of frustrated testing as well.


Hope You enjoy this part...


Regards to All


Ufopolitics

[Zardox]

Nice demo

Nice demo UFO!
Would I be right in assuming that when the super cap was charged to a voltage high enough to run the machine the battery could be disconnected and a second super cap could be put in its place?
I would like to mention my experiment with using the 22 gage wire. It is actually 2 of the goldmine motors set end to end with a gap between the two rotors but wound as one. At this point I need to modify the end plates so I can adjust the timing. As it is it is set at the factory timing. As it is it will not run on the lower voltage as you are showing or maybe my battery just won't put out enough amperage. It does however run just fine on my 10 volt alum converted motorcycle battery. There is no arcing in the commutators and it does not get hot. If the timing was adjusted I think it could do much better as I am only seeing just under about 8 volts on the output. I did hook the shaft directly to a 18 volt trimmer motor with not so good bearings and got 17 volts out of that as well. I don't have much time to work on this at this time of the year so my apologies for not getting things done in more of a timely fashion. I only mention my work in hopes that my results might be of help and do not want to detract from your work in any way.

[Cornboy 555]

Great Stuff UFO, and very well explained, it would be interesting to see what happens if you put a gentle mechanical load on motor shaft.

Warm Regards Cornboy.

[Ufopolitics]

Ufo very nice demo.

Thanks Sam,

When you slip the cap in simply charge it up to battery voltage first, connect in parallel with battery, let it run a little bit, get the voltage up some more, than viola, disconnect battery, smooth, easy peasy.

See Sam, that's what I do NOT want to do now (or pre-charge Supercap by a different source/charger)

What I want to demonstrate (and I will do just that in my next video...) is to show that our Machines, no matter how small the set up is...Machine is ABLE TO CHARGE Supercap ABOVE Starting Battery levels (Generator Capabilities)....trust me, I have done it by now...

Problem with Supercaps is that when they are Zero Charge...or Negative Values...they will become a SHORT CIRCUIT to our Machines...so a very small precharge must be done (200 to 300 millivolts) in order to add some resistance.

I know you will love what is coming next couple of videos...


Take care


Ufopolitics

[sampojo]

YES! most impressive

Ufo very nice demo. When you slip the cap in simply charge it up to battery voltage first, connect in parallel with battery, let it run a little bit, get the voltage up some more, than viola, disconnect battery, smooth, easy peasy.

[Ufopolitics]

Analyzing Diagram...

Hello Again,

On this separate post I will go over about what's going on inside Machine...and why I believe is doing this "Effect":


[IMG][/IMG]

For all of you familiar with My Machines and specifically this type of all North config...

L1 receives a feed from battery, then once magnetized it rotates and becomes L2, here it creates a "momentary" LC Circuit with Supercap, where Cap receives a dumped charge as also L2 magnetizes in resonance for the short time of closed loop, this creates a strong field and acceleration starts becoming more robust...after disconnection it goes back to L1 POSITION, where excess charges are dumped back to Battery...and so on and on...NOW, realize we have here FIVE L#...so it is L1, L2, L3, L4 and L5 swapping places constantly during rotation.

Since ALL COILS are North or same winding directions...they generate same magnetic fields (no matter if North or South)...then the Spatial "Ring" around Rotor is ALL BLUE...or All North...the same direction Energy is "lingering" in its environment...so, "sucking" from this constant UNIPOLAR FIELD is not such a big stress...or such big job...like when Spatial Field is completely canceling to Zero Value at every spin in North-South Configurations.


Hope you see all this clear...because what's coming next is not that simple to "digest"...and has absolutely nothing to do with above...however, they will "blend" perfectly in beautiful harmony in the end...


Regards to All


Ufopolitics

[Ufopolitics]

Ufo I don't understand where the "rear junction" hook up goes and which "two ????? terminals" you are using. I need to see how the G10 does vs the P10 here. where do you hook the bulb up when it looks like you are using gen terminals on the "rear junction".

[IMG][/IMG]

[Ufopolitics]

Supercap Test Part 1

https://www.youtube.com/watch?v=-Afl...0YnD2b5zasXXng

Hello to All,

Above is the First Test I conduct with Supercapacitors...here is just one of them, replacing the typical electrolytic I used on previous video...so We can see how much the Supercap enhances the Effect, on Self Acceleration and Regeneration of Voltage In (V In) at Right hand side Meter.

[IMG][/IMG]

This Test clearly shows that we have a Progressive Regenerative Effect that develops much faster than with typical Electrolytic Caps...more layers...more density of currents.

Caps that I used here are MAXWELL 310 Farads and 2.7 Volts.

I am making Three Videos...this is first...on second I will NOT be using this approach on Cap connection, but a COMPLETELY NEW way to connect a feed to this Machines...then at the Final Video I will be showing the "Fusing" of both type of connections and the "Advantages" I will be very glad to demonstrate.

On the video, sorry about some background sound tracks going a bit crazy on volume levels...but you will see the whole effect clearly.


Thanks and Regards


Ufopolitics