Energetic Forum  
Facebook Twitter Google+ Pinterest LinkedIn Delicious Digg Reddit WordPress StumbleUpon Tumblr Translate Addthis Aaron Murakami YouTube PRE-REGISTER - 19 SEATS LEFT!!!*** 2017 ENERGY CONFERENCE ***


* NEW * BEDINI RPX BOOK & DVD SET: BEDINI RPX


Go Back   Energetic Forum > > >
   

Eric Dollard Official Forum This forum is dedicated to the work of Eric P. Dollard. His Official homepage is http://ericpdollard.com

Bedini RPX Sideband Generator
Reply
 
Thread Tools
  #2611  
Old 07-29-2016, 07:56 PM
Marcus Neuhof Marcus Neuhof is offline
Member
 
Join Date: Nov 2012
Posts: 52
Mr. Dollard,

as a means of further exploring the potential anomalous effects of dielectric parameter variation, I re-wired my prototype / replication of the PP-18, and performed a number of tests with the intent of observing even the finest, most minute appearance of surplus energy in the circuit as a result of dielectric parameter variation.

None were found.

Here were the experiments performed:

In this new configuration, the vibrator coil itself was powered by a separate battery. There was thus no load placed on the condensers and source voltage whatsoever -- apart from resistive losses.

The purpose of this new configuration was to determine if any surplus Joule-seconds were being produced at all.

Given the lack of any significant load, if this configuration of dielectric parameter variation was producing surplus Joule-seconds, then one would expect to see either a voltage gain or at least no voltage drop across the input or output condenser.

The experiment was performed by powering on the vibrator using the separate battery. Then, a second battery was used to charge up the condensers in the circuit.

A volt meter with 0.001mV accuracy was placed across the output (24V) filter condenser, the condenser which is charged by the action of the position-varying condenser in combination with the input condenser.

Upon removal of the "charging" battery, with the vibrator coil still operating off its separate power source, the measurement was observed.

The voltage across the 2200uF output condenser was seen to decrease at a rate of approximately 1 millivolt per second.

Performing the identical measurement across the 6800uF position-changing condenser, with the vibrator still operating, revealted a decrease in voltage of approximately 1 millivolt per 8 seconds.

Finally, the voltage across the 6800uF input condenser was seen to decrease at a rate of approximately 1 millivolt per 6 seconds.

Removing power from the vibrator, the measurements were observed again.

The voltage across the 2200uF output condenser decreased at approximately 1 millivolt per second.

The voltage across the 6800uF position-changing condenser decreased at approximately 1 millivolt per 6 seconds.

The voltage across the 6800uF input condenser decreased at approximately 1 millivolt per 6 seconds.

The observed difference between the rate of voltage decay in the position-changing condenser while the vibrator was operationg, and when it was not, is within the margin of error of my observations.
__________________
 
Reply With Quote

Download SOLAR SECRETS by Peter Lindemann
Free - Get it now: Solar Secrets

  #2612  
Old 07-29-2016, 07:56 PM
Marcus Neuhof Marcus Neuhof is offline
Member
 
Join Date: Nov 2012
Posts: 52
Nevertheless the measurement was performed again using the differential voltage measurement function of the volt meter to measure the change in voltage precisely over a period of one minute.

In this case, a voltage decay rate of 10mV per minute was observed with the vibrator off, and 10mV per minute with the vibrator on.

Measurement of the contact timing with an oscilloscope suggested that both sets of contacts were synchronized to within less than 100 nanoseconds of each other.

Therefore it may be concluded that, while the normally adjusted PP-18 circuit successfully converted an input DC current into an output current of twice the voltage potential, no surplus energy was observed to appear.

Next, adjustment of the vibrator contacts was investigated.

The vibrator contacts were adjusted so as to produce a "cross phased" switching approach: where the contacts responsible for the "Side B" configuration of position-varying condenser in series with the input condenser did not "break" before the "Side A" contacts "made". (Side B being the case where the doubled voltage appears, side A being the condition where the condenser are charged)

(The opposite was incidentally also the case: as a result of this configuration, the Side A contacts did not "break" until after the Side B contacts "made.")

In this configuration, a great deal of sparking was observed from one side of one set of contacts. However, extreme energy loss was observed: the output condenser never reached more than half its operating voltage.

The sparking was observed on the set of contacts which alternate between the input voltage terminal and ground. Specifically, between the negative end of the position-varying condenser and the input voltage terminal.

The contacts were re-adjusted to eliminate the cross-phased action on the other contact set. This way, only the contacts which were observed to produce sparking operated in the cross-phased mode.

Applying voltage, nearly the same effects as with the previous cross-phased configuration were observed. This time, sparks appeared at both A and B contacts in the cross-phased contact set. However, the extreme voltage losses were still observed, and the output voltage condenser only reached half its voltage.
__________________
 
Reply With Quote
  #2613  
Old 07-29-2016, 08:00 PM
Marcus Neuhof Marcus Neuhof is offline
Member
 
Join Date: Nov 2012
Posts: 52
The contacts were then adjusted again, so that only the non-sparking contact set was cross phased. (In other words, the contact set which varies the positive terminal of the position-varying condenser between the input voltage terminal and the output voltage terminal.)

With this configuration, barely any voltage was observed to appear at the output voltage terminal -- the device appeared not to function at all.


Based on these experiments it appears that neither pure dielectric parameter variation, nor the combination of dielectric parameter variation in combination with sparking or cross phased switching, are sufficient to produce energy synthesis in the PP-18 circuit.


Further avenues for experimentation include the possibility of parametric excitation / resonance in combination with the un-labeled inductances in the military PP-18/AR schematic, and/or the other condensers therein.

Mercury-wetted type relays proved to be unavailable at a reasonable price from the suppliers accessible to me. However I was unable to identify avenues for experiment which they would have allowed, but which were not covered by careful adjustment of the vibrator contacts.
__________________
 
Reply With Quote
  #2614  
Old 09-20-2016, 05:03 AM
David G Dawson David G Dawson is offline
Senior Member
 
Join Date: Mar 2008
Posts: 406
Push-Pull Drivers/Variacs

Hello Eric,
Am currently building a 6SN7GTA Push-Pull driver similar to your schematics and find your information most helpful.
In your letter to JohnP on this subject (6N7s and MagAmps), you made the statement:

"So let's see if the miracle of a parameter EMF can be brought out"

Could you please elaborate on exactly what this 'miracle' is?

Have plans to drive the CSI/CRI with this setup and also your 5R4GYB/2050 thyratron pulser for effect.
What I have also not done but see it as a required component is to raise a capacitor hat well above the Extra Coil.

Anything more you would like to pass on with respect to Vacuum Tubes will be most appreciated as you are talking to about one of the very few that have bothered to build all or any of your circuits.
Cosmic Ray Detector (CRD) still working well with the large 8" donger.
However, it is not talking to me although I do note a change in dong frequency at certain times.
Thanks.

Variable Inductor:
Spent quite some time looking for the impossible and eventually found it - this being a large range variable Inductor.
Most you can buy are large ex Transmitter Finals and are of the Roller type but with very limited range.
The IF cans and similar out of Radios are OK but small and the range is still limited using the Ferrite tuneable cores.
Coils with open core bobbins are good with room to fit Ferrites like antenna rods out of old transitor radios but with a still limited variable range.

I had just purchased two NOS Ohmite 120volt 1.5amp VA2 Variacs and put then to the range test and came out with a variable inductance from 3mH to 1.2H and in such solved the problem.
These all have a broad Copper winding which is about 1" wide at top and bottom and in such make an ideal variable inductor and the way in which they are made by Ohmite, have an extremely reliable contact surface.
Only problem here is the cost, USA about $50 but in Oz at $A100 but I went to Ebay where they went cheaply.

All the best.

Smokey
__________________
 
Reply With Quote
  #2615  
Old 11-20-2016, 09:43 PM
Aaron's Avatar
Aaron Aaron is offline
Co-Founder & Moderator
 
Join Date: Feb 2007
Location: Washington State
Posts: 10,419
Eric Dollard in the hospital

Eric is in the hospital but still wants to do a live call - 2pm Pacific today in 15 minutes.

Conference Dial-in: 1-857-232-0155
Conference Code: 582590

Thanks,
Aaron
__________________
Sincerely,
Aaron Murakami

Reply With Quote
  #2616  
Old 01-27-2017, 09:07 AM
h2ocommuter's Avatar
h2ocommuter h2ocommuter is offline
Senior Member
 
Join Date: Sep 2009
Location: Fresno Ca,
Posts: 146
Send a message via Skype™ to h2ocommuter
Any More updates?

Quote:
Originally Posted by Aaron View Post
Eric is in the hospital but still wants to do a live call - 2pm Pacific today in 15 minutes.

Conference Dial-in: 1-857-232-0155
Conference Code: 582590

Thanks,
Aaron
I know I must be out of the loop. Are there any updates about Erics' health?
__________________
 
Reply With Quote
  #2617  
Old 02-28-2017, 08:32 AM
Aaron's Avatar
Aaron Aaron is offline
Co-Founder & Moderator
 
Join Date: Feb 2007
Location: Washington State
Posts: 10,419
Tomorrow live call with eric dollard

ERIC DOLLARD - HE'S RECOVERED AND WILL BE ON A LIVE CALL! - JUST A REMINDER...


February 28th, Tuesday, 3pm Pacific Time, we'll have a live call where you can ask Eric Dollard questions. The topics he DOES want to focus on are Telluric Research, Alexanderson Networks, and other related questions based on any of his books or video presentations. He does NOT want to answer questions relating to topics that are not specifically related to his books/videos.


As you may or may not know, he was in the hospital for about 3 months with a blood cancer and he is now doing really well and we are lucky to have him offer to answer questions live - please honor his request of what he wants to talk about if you get on the call.


Here are the call details, they may not be given again so please write these down and put the date on your calendar:


Conference Dial-in: 1-857-232-0155
Conference Code: 582590
__________________
Sincerely,
Aaron Murakami

Reply With Quote
  #2618  
Old 03-06-2017, 12:59 AM
Aaron's Avatar
Aaron Aaron is offline
Co-Founder & Moderator
 
Join Date: Feb 2007
Location: Washington State
Posts: 10,419
Recording - Eric Dollard Live Call 2017-02-28

Eric Dollard Live Call 2017-02-28 - Eric P. Dollard - Official Homepage
__________________
Sincerely,
Aaron Murakami

Reply With Quote
Reply

Tags
aether, cosmic induction, energy conference, epd laboratories, eric dollard, eric p dollard, ernst alexanderson, extraluminal, generator, longitudinal, steinmetz, tesla, versor algebra, wireless, dollard, eric

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



Please consider supporting Energetic Forum with a voluntary monthly subscription.

For One-Time Donations, use admin@ this domain > energeticforum.com

Choose your voluntary subscription

All times are GMT. The time now is 01:25 AM.


Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimisation provided by DragonByte SEO v1.4.0 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Shoutbox provided by vBShout v6.2.8 (Lite) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
2007-2015 Copyright - Energetic Forum - All Rights Reserved

Bedini RPX Sideband Generator

Tesla Chargers