Energetic Forum  
Facebook Twitter Google+ Pinterest LinkedIn Delicious Digg Reddit WordPress StumbleUpon Tumblr Translate Addthis Aaron Murakami YouTube 2020 ENERGY CONFERENCE - PRE-REGISTER NOW!!!!

2020 Energy Science & Technology Conference
PRE-REGISTER NOW!!!
http://energyscienceconference.com


Go Back   Energetic Forum > > >
   

Eric Dollard Official Forum This forum is dedicated to the work of Eric P. Dollard. His Official homepage is http://ericpdollard.com

* NEW * BEDINI RPX BOOK & DVD SET: BEDINI RPX

Reply
 
Thread Tools
  #691  
Old 02-12-2013, 05:40 AM
dR-Green's Avatar
dR-Green dR-Green is offline
Gold Member
 
Join Date: Apr 2008
Location: Wales, UK
Posts: 1,558
Quote:
Originally Posted by Sputins View Post
I watched the video and it was good to see the ground output lightbulbs lite as well as the bulb on the terminal capacitance. This is bloody good considering only +/- 10.9 volts to the primary. Also I found this video a little clearer to see / understand how the rig set up is exactly.

Is there any difference if you pulse the primary coil with the square wave option on the frequency generator, I.e. experiment with the duty %?
So what kind of power supply are you considering to ramp up to? Are you intending to use sine wave input, or pulsed input? How are you going to interface the frequency generator to the new power supply? When you say 'modern components' do you mean transistors of some sort. What transistors are you using to interface with the frequency generator & primary coil? What EMF / MMF are you intending on using?

It will be nice to see some "corona" coming off of your rig! The higher voltages may make transmissions more effective?

My latest power supply idea which is coming along slowly, consists of the frequency generator, this then tickles a TC4420 MOSFET driver to give zero, +6volts, (square wave) output at the required frequency (the output voltage level is variable). This I then intend to drive a 2050 thyratron tube (perhaps two). (I'm not sure how the TC4420 will go at driving the grid of the thyratron but I can't see why it won't). The plate supply for the 2050 is derived from a small resonant tank circuit, which is then rectified and set to give 600 volts DC. (I'm not sure of the overall power, but it isn't much). So my power supply a 2050 Thyratron driven by a digital interface, the 2050 switching a 600 volt resonant DC supply. This is for impulse drive, to the primary, not oscillation in this case. I'm almost ready to power it up to test.
This arrangment could be altered so that the resonant plate supply is not rectified and is made to be the same frequency as the TMT. Ultimately i'm thinking to make the primary driver as given from Dollard:
The primary is only getting just under +/- 8V with the transistor voltage drops and everything, it only gets that high when I use a primary condenser. It will also go a bit higher again depending on the load on the ground end of the secondary.

I haven't tried a square wave with this setup, only briefly with the setup I used with audio modulation before, a basic 2N2222 amplifier. As I recall varying the duty basically had the effect of varying the amount of power (available at the receiving load), and under a certain pulse width the audio output became garbled.

The maximum with this new circuit will be +/- 15V. The signal generator is currently driving an op amp which is driving TIP120 and TIP125 transistors in a push-pull arrangement. A modulation stage will be added before the op amp for when amplitude modulation is needed, but I haven't started assembling that circuit yet. I intend to use sine waves because I'd like to use (undistorted) signals to experiment with, there are a lot of interesting possibilities like Tesla said. "Signals" of course being a very generic term. In basic terms I want a relatively powerful/versatile signal generator with the option of modulating the amplitude.

I think the threshold for transmission is about +/- 3-4V, but it's impossible to say really because it also depends on the receiver and the load etc. That's about what it takes when I use the original CRI design secondary to power an LED over an earthed transmission line (transmitter and receiver connected by a wire that's earthed). That using only the op amp to power the primary. Current or voltage is one of the things I want to experiment with which is why ideally I want to have independent control over both.

Combining the valves with the circuit Eric posted sounds like a good idea to me. I'd be interested to know how your power supply test goes.
__________________
http://www.teslascientific.com/

"Knowledge is cosmic. It does not evolve or unfold in man. Man unfolds to an awareness of it. He gradually discovers it." - Walter Russell

"Once men died for Truth, but now Truth dies at the hands of men." - Manly P. Hall
Reply With Quote

Download SOLAR SECRETS by Peter Lindemann
Free - Get it now: Solar Secrets

  #692  
Old 02-13-2013, 04:11 PM
Web000x's Avatar
Web000x Web000x is offline
Silver Member
 
Join Date: Apr 2009
Posts: 547
Quote:
Originally Posted by dR-Green View Post
Thank you dR-Green for the link, but the text ends up being too small when I print it. It would be okay if it just had standard text in it but also has superscripts and subscripts in the equations that become illegible when printed. I doubt Eric would get much out of it without being able to see all of the details of the equations.

Can somebody with a scribd account download Method of Symmetrical Co-Ordinates Applied to the Solution of Polyphase Networks-xSf and send it to me? I can't print it off unless I have a copy on my hard drive first. Private Message me for my email address.

Thanks

Dave
__________________
 
Reply With Quote
  #693  
Old 02-13-2013, 07:40 PM
Web000x's Avatar
Web000x Web000x is offline
Silver Member
 
Join Date: Apr 2009
Posts: 547
Quote:
Originally Posted by Web000x View Post
Thank you dR-Green for the link, but the text ends up being too small when I print it. It would be okay if it just had standard text in it but also has superscripts and subscripts in the equations that become illegible when printed. I doubt Eric would get much out of it without being able to see all of the details of the equations.

Can somebody with a scribd account download Method of Symmetrical Co-Ordinates Applied to the Solution of Polyphase Networks-xSf and send it to me? I can't print it off unless I have a copy on my hard drive first. Private Message me for my email address.

Thanks

Dave
Nevermind, Techzombie was kind enough to get it for me. Thanks Tech!
__________________
 
Reply With Quote
  #694  
Old 02-13-2013, 07:46 PM
Aaron's Avatar
Aaron Aaron is offline
Co-Founder & Moderator
 
Join Date: Feb 2007
Location: Washington State
Posts: 10,999
Arrow Method of Symmetrical Co-Ordinates Applied to the Solution of Polyphase Networks-xSf

Quote:
Originally Posted by Web000x View Post
Can somebody with a scribd account download Method of Symmetrical Co-Ordinates Applied to the Solution of Polyphase Networks-xSf and send it to me? I can't print it off unless I have a copy on my hard drive first. Private Message me for my email address.
Method of Symmetrical Co-Ordinates Applied to the Solution of Polyphase Networks-xSf
__________________
Sincerely,
Aaron Murakami

Reply With Quote
  #695  
Old 02-14-2013, 03:32 PM
techzombie's Avatar
techzombie techzombie is offline
Member
 
Join Date: May 2012
Posts: 35
Could you guys please share your favorite radionics pdf files with me?

It is to support Eric's fundraiser.
__________________
 
Reply With Quote
  #696  
Old 02-15-2013, 12:19 AM
David G Dawson David G Dawson is offline
Senior Member
 
Join Date: Mar 2008
Posts: 420
Cosmic Ray Detector

Cosmic Ray Detector:
Completed and not working as was expected after doing some experiments with the 0A4G as Eric suggested in aid to understanding operation of a Gas Triode - cold cathode - starter Anode type.
Tried 150pF, 5,800pf and 10,500pF and best was in the middle.
Lower the pF, the higher the required voltage (about 140) and as you go higher the voltage comes down to about 100 volts and this is for repetitive, 1second pulsing used as the reference requirement.
Most Photocells use 90 to 100 volts as their required voltage.
However, have tried both the 21" Geiger/Mueller Tube and a NOS 868 (early 918) and all I can measure at the trigger point is 1.5v AC.
Why AC I have no idea but this may be Mains AC interference as I am close to a fluorescent at the bench.
Volts set at 150 vDC.

Just do not now see how a Tube in the open as a 'Receptor' can generate 100volts being sufficient to fire the 0A4G.

I do not know what the pulsing rate here would be and may be something like 100 hours or so is needed before the unit will fire.
Eric hasn't covered what this period may be.
There are several 'free energy' devices using long wire antennas and a spark plug to charge a small capacitance or batteries but this is the only other device I could directly associate with.

Anyone doing Thyratron testing for circuits as I am will find Eric's setup on Page 12 Post 347 '0A4G Neon Detector Tube' (Argon) and also for Geiger/Mueller Tubes and Photocells, most helpful.

Putting this aside but will leave in the background powered up for observation and concentrating on the pulsing of the TMT using the 2050 and the Jerry Bales Tubes and 'The Radiant Energy Tube' as time permits.

Have won myself a Morse Key on Ebay and boning up on the Code again after some 52 years and I was a terrible operator, not my thing but time may have changed all of that, now being Telluric communication.

Smokey
__________________
 
Reply With Quote
  #697  
Old 02-15-2013, 12:25 AM
David G Dawson David G Dawson is offline
Senior Member
 
Join Date: Mar 2008
Posts: 420
Radionics

techzombie,
Excellent work you are doing here.

Could you guys please share your favorite radionics pdf files with me?

Dr Ruth Drown and Dr Albert Abrams - what specifically are you after here and can you elaborate on why Radionics?
Huge field and need specifics.
Dowsing?
Thanks.

Smokey
__________________
 
Reply With Quote
  #698  
Old 02-16-2013, 09:28 PM
Infunity Infunity is offline
Junior Member
 
Join Date: Feb 2011
Posts: 24
Quote:
Originally Posted by David G Dawson View Post
Cosmic Ray Detector:
Completed and not working as was expected after doing some experiments with the 0A4G as Eric suggested in aid to understanding operation of a Gas Triode - cold cathode - starter Anode type.
Tried 150pF, 5,800pf and 10,500pF and best was in the middle.
Lower the pF, the higher the required voltage (about 140) and as you go higher the voltage comes down to about 100 volts and this is for repetitive, 1second pulsing used as the reference requirement.
Most Photocells use 90 to 100 volts as their required voltage.
However, have tried both the 21" Geiger/Mueller Tube and a NOS 868 (early 918) and all I can measure at the trigger point is 1.5v AC.
Why AC I have no idea but this may be Mains AC interference as I am close to a fluorescent at the bench.
Volts set at 150 vDC.

Just do not now see how a Tube in the open as a 'Receptor' can generate 100volts being sufficient to fire the 0A4G.

I do not know what the pulsing rate here would be and may be something like 100 hours or so is needed before the unit will fire.
Eric hasn't covered what this period may be.
There are several 'free energy' devices using long wire antennas and a spark plug to charge a small capacitance or batteries but this is the only other device I could directly associate with.

Anyone doing Thyratron testing for circuits as I am will find Eric's setup on Page 12 Post 347 '0A4G Neon Detector Tube' (Argon) and also for Geiger/Mueller Tubes and Photocells, most helpful.

Putting this aside but will leave in the background powered up for observation and concentrating on the pulsing of the TMT using the 2050 and the Jerry Bales Tubes and 'The Radiant Energy Tube' as time permits.

Have won myself a Morse Key on Ebay and boning up on the Code again after some 52 years and I was a terrible operator, not my thing but time may have changed all of that, now being Telluric communication.

Smokey
Hey Smokey, not sure this is completely relative but i thought this idea might give you some ideas. I was looking into oscillating systems that were up in the femtohertz range because i suspect these frequency ranges hold the primary or secondary harmonics of cosmic background radiation which i believe is the resonance of the spacetime field across our region of the universe. Just a theory, but if one where to resonate a receiver with a signal oscillating with a wavelength equivalent to the some of the smallest units of spacetime, it would mean you would have to tune to it. Moray suggested this energy came in waves so tuning was facilated by the fact that the rate radioactive decay is coupled to the frequencies the waves were arriving at. This assumed that radioactive decay was a direct result of structural instability under the pressures of the energy that permeates our spacetime. So, these frequencies are pretty high up there. I suggest that one way to tune to these changing frequencies that carry energy like waves across the universe, is to use a sensor that resonates with the stronger harmonics, and then uses a step down oscillator that can resonate physical matter with a direct harmonic of the source's changing frequency. Radioactive decay can stimulate electric flow oscillation to resonate an antenna with the source, but i believe a conductor can also carry these oscillations in its electic flow, and that this flow could be used to activate a switch through which another oscillator could be resonated. Unfortunately, the fastest transistors don't cut it, graphene transistors are closest, so i believe a method for amplifying the signal and stepping down the frequency is to use lasers, coupled to one another like gears, as are used in femtosecond pulse trains for super clocks. Once you can couple the souce frequency to a resonating receiver, i think you can harness the energy bombarding the earth in waves like Moray talked about.
__________________
 
Reply With Quote
  #699  
Old 02-16-2013, 09:43 PM
Infunity Infunity is offline
Junior Member
 
Join Date: Feb 2011
Posts: 24
Hey Techzombie
And this goes out to Dave too

We've talked about helping Eric out, and you guys know i want to contribute, and so do lots of other people, but we can't give him anything but money until he has a place to keep more possessions. Where does he want a lab? I can really help him get settled out here, but its up to him. Where does he want to work? I want to help him get all the physical stuff he needs to further his research and development of this antenna array. With all the people we know that want to help Eric we could easily buy the land he needs to work on. That way he isn't worrying about the possibility of his stuff getting lost because of rent and landlord related issues. Anyways, lets talk about what we can do to get Eric goin' again! I think one of us oughta go see him again so we can arrange moving somewhere! I'm relatively close, and i already know how meet up with him, so i might go for ya. At least you can call me on the silly phone; i'll cook my brain to relay the messages faster! He has a lot to tell us about what he needs in his new lab. Anyways, i'll try to stay available.

Edward "Alex" Loseman
Alloseman@aol.com
Skype: steelbaboon
Facebook.com/loseman
__________________
 
Reply With Quote
  #700  
Old 02-16-2013, 10:05 PM
techzombie's Avatar
techzombie techzombie is offline
Member
 
Join Date: May 2012
Posts: 35
David,

I want to offer a collection of books about electro healing/radionics ask perks for Eric's fundraiser.

I'll take whatever you have.


Quote:
Originally Posted by David G Dawson View Post
techzombie,
Excellent work you are doing here.

Could you guys please share your favorite radionics pdf files with me?

Dr Ruth Drown and Dr Albert Abrams - what specifically are you after here and can you elaborate on why Radionics?
Huge field and need specifics.
Dowsing?
Thanks.

Smokey
__________________
 
Reply With Quote
  #701  
Old 02-16-2013, 11:58 PM
David G Dawson David G Dawson is offline
Senior Member
 
Join Date: Mar 2008
Posts: 420
TH Moray Replication

Hello Alex,
Thankyou for your input.
Just went back and reread your 'resume' and was most impressed, again, - how is it all going?
Three projects I have on the board are all associated with the TH Moray replication.
The 'Cosmic Ray Detector' was sent to us/me by Eric as a back end detector and it's up to us/me to find out how to get the 100volts out of the Cosmos required to fire the 0A4G, anyway, that's as I see it - a challenge!

'The Radiant Energy Tube':
or 'Gas Diode' from Bruce Perrault is all prepared to go and just need the fittings collected and the Calcium Hypochlorite to make the Chlorine.
The only Zinc I could get was 325 mesh, which to me is too fine as the Iron Pyrite I had crushed to about 10 to 20 mesh which is about 1 to 2 mm size.
Remembering here that the gas needs to be saturated throughout the mix so am looking at something to add to the Zinc to space it out a little.
Looking on this as a super 1N34 and may give me the starting voltage required where an outside energy source is immediately excluded.
Have Bismuth here which is something of an unknown and is an Alpha emitter and in between magnetism and radioactivity and may be a good catalyst to use.
Bismuth has properties not at all well known apart from being diamagnetic - I am using these as 9mm pellets in the David Lowrance Rainmakers and their exact purpose is still not quite revealed.
Is the Chlorine gas used here as a carrier between the two grids as the porous Pyrex filter is the dividing medium?

Jerry Bales Hydrogen hyperfine frequency Tubes:
('Tornado Tubes') also set to go as the 'BoomBox' input from the Sig Gen works well into the Microphone input in 'Tape' mode.
Mum's audible range is not bad at 12.6khz (66years) and mine is about 11.6khz (70years).
Am able to read to 1 hertz accuracy and that is also a bonus.
Been wanting to set this up for some time and can now also do Cymantics with sand as that is where hidden messages can be revealed.
Been raining here and not had a chance to take this outside as I need to be able to erect it at an angle against the house roof flashing or tree as elevation may be of interest and also magnetic north.

My RF life has been associated with frequencies from VLF at 40 Khz through to 'Water Maser' at 24 Ghz but see a gap at the top end of the UHF Band at 900 Mhz and then to S-Band at about 2.4 Ghz, nobody appears to work in this gap.
Jerry Bales has pointed out the Hydrogen hyerfine frequency at 1.42 Ghz and this is the only one that I can see that is significant to this particular area.
Correct me if I am wrong but get this feeling that somewhere in there is where the magic happens.
Don't think it is out of our reach in the femtohertz region but is accessible by lesser means and strongly believe in the KISS principle that it is not out of our comprehension.

Powering the CSI this week and been delaying this for too long and looking forward to some illuminating results, pardon the pun.

Aaron,
Many Thanks for supplying Eric's Fortescue document, was about to download the Scribd source and saw your input - most appreciated!
That document is way TOO deep for me but am glad that others can see something of value.

Smokey
__________________
 
Reply With Quote
  #702  
Old 02-17-2013, 11:24 AM
David G Dawson David G Dawson is offline
Senior Member
 
Join Date: Mar 2008
Posts: 420
Bismuth

1927 was a magic year for some where developments in the new Radio technology were either lost or gained.
This one was right on top of TH Moray and bought out by Westinghouse, never to be seen again, well not until now that is:

Quote:
He styled the device “an application of bismuth plates as detectors and amplifiers”, which could be used in place of present batteries and vacuum tubes in a radio.

http://fultonhistory.com/Newspaper%2...20-%200036.pdf

So we follow the trail and view the Patent:

Palmer Craig: Hall Effect Device (Battery, rectifier, amplifier)

The only application that ever came out from this in what we have in use today as the Hall Effect device.

Moshe of Joe Cell fame has a good overall coverage of Bismuth:

Bismuth the Metal - Moshe's favourite element - Bismuth metallicum

Would very much like to make Bismuth sheet as it is easy to work with and a bit like Lead, temperature wise.
Has distinct possibilities as Moray discovered.

Smokey
__________________
 
Reply With Quote
  #703  
Old 02-17-2013, 11:59 AM
David G Dawson David G Dawson is offline
Senior Member
 
Join Date: Mar 2008
Posts: 420
Radionics

techzombie,
Quote:
"I want to offer a collection of books about electro healing/radionics ask perks for Eric's fundraiser.

I'll take whatever you have."

OK, had to go through Radionics to get to where I am today and have a rather large Library.

Dowsing a good start:

A Mini-Course in Pendulum Dowsing

Unfortunately most of what I have in books will no longer be available through a URL as it took many years to build the Library.
This is the site where I first began in Radionics and led into Weather Engineering through TJ Constable:

Dr. Ruth B. Drown, America's Greatest Radionics Innovator, The Untold Story Part 1

Tried to find his book 'The Cosmic Pulse Of Life' but no longer available except via a bookshop.
That was the first book I read on retirement and basically set myself up with some sort of an understanding of what it was all about in both Radionics and the Weather aka the Aether.
Dr Hulda Clark is there too and a few others.

Will get back to you as I find access to the material.

Smokey
__________________
 
Reply With Quote
  #704  
Old 02-17-2013, 12:17 PM
David G Dawson David G Dawson is offline
Senior Member
 
Join Date: Mar 2008
Posts: 420
Radionics

techzombie,

Trevor James Constable

See the first and second last 'The Visual Ray'.
Have actually done this and it works and shows you what power you have in your eyes, just like Superman as this is what it is telling you.

Anything to do with TJ Constable is kind of Radionics associated and it all boils down to being Witch like as this is what they were burnt at the stake for - messing with the Aether and nothing to do with Satan.
I keep looking behind me.

Borderland Sciences (BSRF) under Meade Layne were just so far ahead of the mob and that is where I started.

Smokey
__________________
 
Reply With Quote
  #705  
Old 02-17-2013, 08:08 PM
Aaron's Avatar
Aaron Aaron is offline
Co-Founder & Moderator
 
Join Date: Feb 2007
Location: Washington State
Posts: 10,999
Trevor Constable

All of Trevor Constable's books, videos, etc... are copyrighted and are not available for a free download. I have some of his work available here: Trevor James Constable | Real Rain Making | Official Website. We have the only company right now that actually pays Trevor a royalty on his work, while everyone else is selling his work without permission and without giving him anything. He had a stroke a couple years ago and isn't doing well, we need to be fair to him.

If Cosmic Pulse, etc... are found online, they will be taken down.
__________________
Sincerely,
Aaron Murakami

Reply With Quote
  #706  
Old 02-17-2013, 09:33 PM
madhatter's Avatar
madhatter madhatter is offline
Senior Member
 
Join Date: Nov 2010
Posts: 457
been busy lately with the buisness, just finished up the refurb on the power supply unit I picked up. some before and after pics. debating on going to the trouble of silkscreening labels on the front.

acquired some more parts, working on yet more math and sorting the schematics Eric has shared.




__________________
 
Reply With Quote
  #707  
Old 02-17-2013, 10:17 PM
techzombie's Avatar
techzombie techzombie is offline
Member
 
Join Date: May 2012
Posts: 35
Thank you David, great info.!

It seems that the actual pdf's of the best radionics books are extremely difficult to find online....

does anyone have pdf's of expired copyrights on alternative/aetheric healing in general?



Quote:
Originally Posted by David G Dawson View Post
techzombie,

Trevor James Constable

See the first and second last 'The Visual Ray'.
Have actually done this and it works and shows you what power you have in your eyes, just like Superman as this is what it is telling you.

Anything to do with TJ Constable is kind of Radionics associated and it all boils down to being Witch like as this is what they were burnt at the stake for - messing with the Aether and nothing to do with Satan.
I keep looking behind me.

Borderland Sciences (BSRF) under Meade Layne were just so far ahead of the mob and that is where I started.

Smokey
__________________
 
Reply With Quote
  #708  
Old 02-17-2013, 10:58 PM
Aaron's Avatar
Aaron Aaron is offline
Co-Founder & Moderator
 
Join Date: Feb 2007
Location: Washington State
Posts: 10,999
psychotronics related

Quote:
Originally Posted by techzombie View Post
Thank you David, great info.!

It seems that the actual pdf's of the best radionics books are extremely difficult to find online....

does anyone have pdf's of expired copyrights on alternative/aetheric healing in general?
Visit Energetic Science Ministries™ | Resource Library

There are 2 parts - two great papers about Egely here. They're free for distribution to the best of my knowledge.
__________________
Sincerely,
Aaron Murakami

Reply With Quote
  #709  
Old 02-17-2013, 11:08 PM
dR-Green's Avatar
dR-Green dR-Green is offline
Gold Member
 
Join Date: Apr 2008
Location: Wales, UK
Posts: 1,558
Does anyone know why bulbs start to light in open circuits at high frequencies? I burnt out the first bulb last night, the glass is black inside, there's clearly a decent amount of power going through it into the earth. This is a result of minor adjustments to the (secondary) coil, the supplied power hasn't been increased at all.

This was one of the grain of rice bulbs. Measured resistance = 7 ohms. Halving this resistance at the ground end by putting two bulbs in parallel has the opposite effect of what one might expect - rather than the energy more easily flowing into the earth, the bulb at the top of the extra coil gets brighter. Although I suppose the bulbs in parallel are dissipating less energy (a lot less light is produced) so by conventional thinking the bulb at the other end "should" get brighter, but in reality it's an easier path to earth through the parallel bulbs, why should the bulb at the top of the extra coil get brighter at all.

The energy also seems to want to "spill" into receivers even though the transmission line/wire that's connecting them is earthed, with quite poor connections to the receiver. It's quite curious how there's "practically zero" volts at the ground end of the receiving secondary coil, but 20 turns of coiled wire later there is "high(er)" voltage which is detectable without physical connection to anything, the voltage gradient over the receiving coil is observable with an AV plug. The receiver can clearly be seen to be in resonance due to the fact that by touching the grounded parts of the circuit it continues to work as normal, but touching anything that has gone through coiled wire causes it to stop working (including the usual effects of body capacitance near it).
__________________
http://www.teslascientific.com/

"Knowledge is cosmic. It does not evolve or unfold in man. Man unfolds to an awareness of it. He gradually discovers it." - Walter Russell

"Once men died for Truth, but now Truth dies at the hands of men." - Manly P. Hall

Last edited by dR-Green; 02-17-2013 at 11:12 PM.
Reply With Quote
  #710  
Old 02-17-2013, 11:28 PM
David G Dawson David G Dawson is offline
Senior Member
 
Join Date: Mar 2008
Posts: 420
Trevor James Constable

Aaron, techzombie,
I was most surprised when I first saw 'Cosmic Pulse of Life' available for free and actually did download it just to confirm but note now the loopholes have been closed off as you say.
Besides that book I also bought 'Loom Of The Future' which is where I gleaned my Rain Engineering detail from.
The schematics/circuit diagrams don't exist in these books but just so much information is provided and you have an intent, you can glean the missing bits.
Learn the word 'Intent' and what it means and add a smile and the magic happens.
Anyone that has read my Aetheric Rain Engineering pdfs can see that a good part of it is Radionics associated and includes messing with Crystals.

I can sit here doing my daily weather download and begin drawing circles on the synoptic charts where I feel that rain is needed as I happened to do yesterday and today, bingo, right where I wanted it and now you can explain that to me so that everybody understands.
To the best of my knowledge the system that generated that rain did not previously exist and have now excluded coincidence as one of the involved possibilities.

If you go to the Borderlands site you will see certain material that has been released for download and at the bottom of page suggests other closely associated topics like this:

L. George Lawrence | Borderland Sciences Research

And this:

Experimental Electroculture Part 1.pdf - SchematicsForFree.com

And this from the Journals:

Detecting Biodynamic Signals, I | Journal of Borderland Research

Radionics is closely associated with Electrometer or' Life Force' measurement and this I also do in the background.
I have built Dr Hulda Clark's 'Syncrometer' (and others) but must admit to not having the time to fully test these devices as it is not prime focus.

Gregory Hodowanec is also one I would include in this measurement field with his 'Rhysmonic Cosmology':

Gregory Hodowanec: Rhysmonic Cosmology (Index of Articles)

I will do a show and tell now that I can present pictures.

My goal would be to set up a Lab that involves others where we could fully evolve these devices to a stage of complete replication.
That's why I invited Eric to Oz but can't see that happening.

BSRF (Borderlands Science & Research Foundation) in Garberville, California near Eureka in amongst the Redwoods is after donations to allow them to present all of their collected Files into Journal presentations like as displayed in the last URL.

I apologise for my long Posts but I have a lot to offer.

Smokey
__________________
 
Reply With Quote
  #711  
Old 02-17-2013, 11:45 PM
David G Dawson David G Dawson is offline
Senior Member
 
Join Date: Mar 2008
Posts: 420
Madhatter,
Beautiful work, you have done an excellent job!
Makes one feel good, doesn't it?

dR-Green,
Yes, I know what you are describing and my feeligs are that you have set up through the coil, standing waves which will be voltage amplified but no current.
Think this is why body and touch capacitance kill the one wire energy.
Find this same effect with the Extra Coil but when you go to the variable capacitor which I have set up between Secondary and Extra, you can improve signal strength by the hand at a certain distance.
A surface wave like LMD and not TEM, my little 1N34 probe and headphones would tell you more.

techzombie,
Next one with Eric would you please ask him about his 'Cosmic Ray Generator' (CRG) with the large bulb and how he was able to poke a piece of Copper wire through the hot spot in the glass.
This is the Tesla 'Radiant Energy' at work where somewhere on the glass surface, the glass will become molten.
Think others here would also like to know a little more about the CRG in general as several of us here are building this device.
Thanks.

Smokey
__________________
 
Reply With Quote
  #712  
Old 02-17-2013, 11:54 PM
madhatter's Avatar
madhatter madhatter is offline
Senior Member
 
Join Date: Nov 2010
Posts: 457
Quote:
Originally Posted by dR-Green View Post
Does anyone know why bulbs start to light in open circuits at high frequencies? I burnt out the first bulb last night, the glass is black inside, there's clearly a decent amount of power going through it into the earth. This is a result of minor adjustments to the (secondary) coil, the supplied power hasn't been increased at all.

This was one of the grain of rice bulbs. Measured resistance = 7 ohms. Halving this resistance at the ground end by putting two bulbs in parallel has the opposite effect of what one might expect - rather than the energy more easily flowing into the earth, the bulb at the top of the extra coil gets brighter. Although I suppose the bulbs in parallel are dissipating less energy (a lot less light is produced) so by conventional thinking the bulb at the other end "should" get brighter, but in reality it's an easier path to earth through the parallel bulbs, why should the bulb at the top of the extra coil get brighter at all.

The energy also seems to want to "spill" into receivers even though the transmission line/wire that's connecting them is earthed, with quite poor connections to the receiver. It's quite curious how there's "practically zero" volts at the ground end of the receiving secondary coil, but 20 turns of coiled wire later there is "high(er)" voltage which is detectable without physical connection to anything, the voltage gradient over the receiving coil is observable with an AV plug. The receiver can clearly be seen to be in resonance due to the fact that by touching the grounded parts of the circuit it continues to work as normal, but touching anything that has gone through coiled wire causes it to stop working (including the usual effects of body capacitance near it).
tungsten filament bulbs have a tiny coil of tungsten, that small coil will have a resonance peak of its own, that may play a part. the bulb is a simple ballast resistor, depending on where in the circuit your putting it will effect the extra coil. ballast resistors are fascinating in behavior over traditional resistors. the bulb will behave as a current limiter/regulator due to the thermionic action of the filament, the resistance will vary as the temperature changes.
__________________
 
Reply With Quote
  #713  
Old 02-18-2013, 12:05 AM
Aaron's Avatar
Aaron Aaron is offline
Co-Founder & Moderator
 
Join Date: Feb 2007
Location: Washington State
Posts: 10,999
radionics

Quote:
Originally Posted by David G Dawson View Post
Learn the word 'Intent' and what it means and add a smile and the magic happens.
Reich talked about the Y-Factor but it took forever for anyone to learn what it meant - you just spelled it out almost. The Y-Factor is the YOU-Factor and that is what allowed his orgone motors to run.

Most members here at Energetic Forum don't know it, but I had this forum setup originally to be a support board for PATHS - the most advanced "quantum" or aetheric mind technology ever developed. It basically made all commonly known radionics methods obsolete. It works even if there is no intent involved, which has most people in the radionics world scratching their head. But, it does require that anyone on the receiving end does have a subconscious mind, which is identifiable in the collective. It isn't frequency based, it is based on a principle that the subconscious mind communicates in a "universal language" that is common to every human regardless of the language they speak. That code has been cracked and is one of the most important discoveries in history.

Even the QXCI/EFPX/SCIO is a radionic frequency broadcast machine. Bill Nelson simply did everything he could to get away from that language, but that is exactly what that machine is - a computerized radionic frequency broadcaster.

I'll see if I can post more radionics related documents.
__________________
Sincerely,
Aaron Murakami

Reply With Quote
  #714  
Old 02-18-2013, 12:06 AM
madhatter's Avatar
madhatter madhatter is offline
Senior Member
 
Join Date: Nov 2010
Posts: 457
Quote:
Originally Posted by David G Dawson View Post
Madhatter,
Beautiful work, you have done an excellent job!
Makes one feel good, doesn't it?

dR-Green,
Yes, I know what you are describing and my feeligs are that you have set up through the coil, standing waves which will be voltage amplified but no current.
Think this is why body and touch capacitance kill the one wire energy.
Find this same effect with the Extra Coil but when you go to the variable capacitor which I have set up between Secondary and Extra, you can improve signal strength by the hand at a certain distance.
A surface wave like LMD and not TEM, my little 1N34 probe and headphones would tell you more.

techzombie,
Next one with Eric would you please ask him about his 'Cosmic Ray Generator' (CRG) with the large bulb and how he was able to poke a piece of Copper wire through the hot spot in the glass.
This is the Tesla 'Radiant Energy' at work where somewhere on the glass surface, the glass will become molten.
Think others here would also like to know a little more about the CRG in general as several of us here are building this device.
Thanks.

Smokey
thanks, it surprisingly wasn't that difficult to clean up, bakelite is far superior to plastics today. I replaced all the dry caps and went over the solder connections. looking over the layout and the schematic I made off it, the one transformer that feeds to two terminals and the indicator bulb seem to be off the input side of the transformer while the HV leads are wired to the low voltage variac and also feeds to the filament on tube. I get that to a certain extent as the HV rectified voltage would be on the filament leads, but how is that going to handle the current draw for heating the tube? need to some more digging on that transformer, it's not labeled other than some ink stamps... should re-draw the schematic. I didn't have a small replacement bulb on hand for the indicator so I put in a neon bulb with a 175kohm resistor, not entirely sure what the voltage on that circuit will be though..
__________________
 
Reply With Quote
  #715  
Old 02-18-2013, 12:10 AM
Infunity Infunity is offline
Junior Member
 
Join Date: Feb 2011
Posts: 24
I feel like a hundred volts out of the cosmos is hard to do with a small antenna.. A large antenna might get interference from covering such a large area. Goodness, how will you fire that thing.. I'll be thinking it over!
__________________
 

Last edited by Infunity; 02-18-2013 at 12:13 AM.
Reply With Quote
  #716  
Old 02-18-2013, 12:18 AM
dR-Green's Avatar
dR-Green dR-Green is offline
Gold Member
 
Join Date: Apr 2008
Location: Wales, UK
Posts: 1,558
Quote:
Originally Posted by madhatter View Post
tungsten filament bulbs have a tiny coil of tungsten, that small coil will have a resonance peak of its own, that may play a part. the bulb is a simple ballast resistor, depending on where in the circuit your putting it will effect the extra coil. ballast resistors are fascinating in behavior over traditional resistors. the bulb will behave as a current limiter/regulator due to the thermionic action of the filament, the resistance will vary as the temperature changes.
Yes, Farmhand made a video before using a bulb as an inductor I think and it produced the usual high voltage spikes when pulsed.

But in this situation, why is the current flowing? It wouldn't work at 50 cycles, so why at higher frequencies? I don't think the resonance of the bulb itself is much of a factor in this case because different bulbs work the same, the only difference being the brightness, but the point is they work.

Taking the thermionic action into consideration, the resistance decreases as the temperature increases, but to what extent? Less than 3.5 ohms (= 2 parallel bulbs)? It gets difficult then because of the power dissipated by the single bulb compared to the parallel bulbs. There just seems to be energy flowing to places where it "shouldn't", as if action without equal and opposite reaction, at least none that's intuitively observable. It flows through the filament to earth and causes it to light from the "nothingness" on the other end. That is, it readily dissipates this energy in the form of light/heat, when it's free to escape on the other end. Why light the bulb?

The same equally applies to the receiver. Why flow into the receiver and power the load, when there's an easier path to earth.
__________________
http://www.teslascientific.com/

"Knowledge is cosmic. It does not evolve or unfold in man. Man unfolds to an awareness of it. He gradually discovers it." - Walter Russell

"Once men died for Truth, but now Truth dies at the hands of men." - Manly P. Hall

Last edited by dR-Green; 02-18-2013 at 12:26 AM.
Reply With Quote
  #717  
Old 02-18-2013, 03:10 AM
Nhopa Nhopa is offline
Senior Member
 
Join Date: Nov 2011
Posts: 134
Trevor James Constable

Amazon sells "The Cosmic Pulse of life", in paperback, for $19.96. Orders over $25, shipping is free. I just thought you would like to know.
__________________
 
Reply With Quote
  #718  
Old 02-18-2013, 03:22 AM
David G Dawson David G Dawson is offline
Senior Member
 
Join Date: Mar 2008
Posts: 420
Pendulum Dowsing

Radionics and Dowsing go hand in hand.
Hanging above my bench is a Brass key and this is used for Pendulum Dowsing.
If I require answers I will us the key for this purpose but also do acknowledge that I use it too infrequently.
This happened just now.

Question asked of the Key:
The Key is held above a 24A Vacuum Tube, a NOS Kenrad that arrived last week making 14 in total.

"Is the 24A the Vacuum Tube that Nikola Tesla used in his Pierce Arrow with his electric motor back in 1931 with Mr Savo in attendance"?

You first must introduce yourself to the key and tell it what you want and in this case I asked for a 'yes' answer to swing right and left and for a 'no' answer to swing up and down or north and south and you will note that this is contrary to convention.
The response was an emphatic 'yes' a left to right.
I then told the Key 'thankyou' and asked it to stop and it did.

I then asked for a confirmation of that result by now moving in an up/down direction and again the response was emphatic.

Telling the Key to stop and it did.
End of session and took about 3 minutes.
Now, does that sound like Witch Craft or what?
I would rather it be called 'Radionics'.
Thanks.

Smokey
__________________
 
Reply With Quote
  #719  
Old 02-18-2013, 06:20 AM
garrettm4 garrettm4 is offline
Senior Member
 
Join Date: Oct 2010
Location: Orbiting Sol somewhere in the Milky Way
Posts: 178
Interesting Results

Quote:
Originally Posted by dR-Green View Post
Does anyone know why bulbs start to light in open circuits at high frequencies? I burnt out the first bulb last night, the glass is black inside, there's clearly a decent amount of power going through it into the earth. This is a result of minor adjustments to the (secondary) coil, the supplied power hasn't been increased at all.

This was one of the grain of rice bulbs. Measured resistance = 7 ohms. Halving this resistance at the ground end by putting two bulbs in parallel has the opposite effect of what one might expect - rather than the energy more easily flowing into the earth, the bulb at the top of the extra coil gets brighter. Although I suppose the bulbs in parallel are dissipating less energy (a lot less light is produced) so by conventional thinking the bulb at the other end "should" get brighter, but in reality it's an easier path to earth through the parallel bulbs, why should the bulb at the top of the extra coil get brighter at all.

dR-Green,

Just wanted to say I think your doing some fantastic work, as usual! There definitely needs to be more open and clear headed people like yourself doing experiments!

For clarification, when you say the grain of rice incandescent bulb ("grain of wheat" where I'm from) lights in an open circuit, you're referring to a free bulb, outside of the circuit, with leads open right? Or is this with just one wire connected to the circuit, and if so at what point?

I'm probably wrong on this, but in an "open circuit" condition, three possible modes of energy coupling are possible, Electrostatic, Magnetic & Electro-magnetic. The first is purely capacitive coupling, the second is magnetic coupling (but requires a closed "loop" though so this is obviated by the circuit conditions at hand), the third is radio absorption, either as a "black body" or merely as a reflector having a certain amount of attenuation associated with it.

The bulbs are most likely acting as either a lossy conductor for a mutual terminal of some sort of capacitive loop or acting as a lossy radio reflector having high attenuation upon reflection, both would yield the same effects - heating of the filaments. Oscillations of the filament should be nill, due to extremely high AC resistance - the natural logarithmic decrement would be very high, probably enough to preclude oscillation. If the circuit isn't radiating large amounts of RF energy (and have the directivity to focus enough of it to be meaningful), it most likely comes down to the capacitive mode of energy coupling.

As for "thermionic emission", while I'm not a physicist, I don't think this is a major factor in the heating of the filament, merely something that the filament "could" do when it is hot enough to release electrons - thus not really anything of importance in this case. The V/I characteristics of incandescent filaments is quite interesting, as Madhatter has pointed out, non-linear and contains a region of negative slope (negative differential resistance). (When an Iron filament is used in a hydrogen atmosphere, the resistivity becomes even more complex due to the sequestration of hydrogen by the iron. Resulting in the filament increasing in resistance when cold (sequestrated hydrogen increases resistivity) and decreasing when hotter (hydrogen is released as temp goes up). At a certain temperature the filament returns to the normal characteristic curve, resistance goes up with temp, (as in the absence of hydrogen) all resulting in a complex constant current source - basically a variable resistor that maintains a specific current within certain operating voltage limits)

If the bulb isn't truly an open circuit, that is, connected from secondary to the earth as I think you've described, then the earth current from the Tesla Transformer (which is basically an odd form of "electrical pump") would of course burn out the bulb when operating with finer tuned conditions - i.e. greater earth current.

As far as I understand, the electrostatic potential of the extra SHOULD increase as the earth current increases, this is the basic operation of the pump - more "earth current" = greater "terminal potential". Which is the ultimate problem of the Tesla Transformer, it eventually turns into a "4th of July sparkler" when you tune it just right, lots of earth current and subsequently too much electrostatic potential to contain at the terminal end - eventually the air dielectric ruptures and the light show begins. This of course, when you apply some serious current to the primary, like the thyratron circuit that Mr. Dollard has drawn up, or other equivalent high di/dt circuits.

From my understanding of the 3 coil circuit, the primary is purely a translational component following Kirchhoff's laws. However, the secondary and the extra are both ran as oscillating coils of differing characteristic impedance functions, not following Kirchhoff's circuital laws (current in does not equal current out, respective to each of the two terminals of each network). The impedance mismatch causes a partial reflection to take place at the junction between the two oscillating coils (point where differential impedance change per unit length is greatest). Which in my opinion, is what facilitates the pumping action of the earth current. A portion of energy makes it's way to the extra, exciting it, but most is bounced back to the secondary. Then you have the concatenation of both waves (from extra and secondary respectively), adding together as a 1/2 wave but in phase, rather than anti-phase. Resulting in the extra's terminal voltage rising in step with the secondary's earth current to form a sudo reflection amplifier type action.

Just wanted to say I'm not here to impose any "theories" (we all have our own views), just giving my two cents (which is most likely in err) for what it's worth. Keep up the interesting work!

Garrett
__________________
 

Last edited by garrettm4; 02-18-2013 at 07:23 PM.
Reply With Quote
  #720  
Old 02-18-2013, 07:50 AM
dR-Green's Avatar
dR-Green dR-Green is offline
Gold Member
 
Join Date: Apr 2008
Location: Wales, UK
Posts: 1,558
Thank you Garrett.

Quote:
Originally Posted by garrettm4 View Post
For clarification, when you say the grain of rice incandescent bulb ("grain of wheat" where I'm from) lights in an open circuit, you're referring to a free bulb, outside of the circuit, with leads open right? Or is this with just one wire connected to the circuit, and if so at what point?
I've put a diagram below. As far as I could find on ebay "grain of rice" and "grain of wheat" were different sized bulbs, although I didn't look too far into it and I don't remember which mine were actually named as.

Quote:
Originally Posted by garrettm4 View Post
As far as I understand, the electrostatic potential of the extra SHOULD increase as the earth current increases, this is the basic operation of the pump - more "ground current" = greater "terminal potential". Which is the ultimate problem of the Tesla Transformer, it eventually turns into a "4th of July sparkler" when you tune it just right, lots of ground current, and too much electrostatic potential to contain at the terminal end, eventually the air dielectric ruptures and the light show begins.
Yes I see, that makes sense. It would seem that the current flowing through to the earth is what causes that bulb to light, and the higher potential of the extra coil causes the other bulb to light. (Although why does this only happen at higher frequencies?) The bulb WILL NOT light on the ground end of the coil with an equal capacitance as is used on the top of the extra coil, it needs a much bigger capacitance I.E. the earth. So in other words it either needs a massive capacitance or a high potential to work in open circuit/single wire mode. "High" potential being only just capable of lighting fluorescent tubes and keeping them lit within about 5-10cm of the extra coil/terminal, and a neon bulb with metallic contact.

It all gets more interesting/confusing when some bulbs work and some don't. A 28V bulb will light up on the ground end, but a 2V bulb won't etc. I can't even get a Mini Maglite bulb to light, but the 28V bulb will. I haven't made a note of the resistance of all the bulbs but there's no apparent logic to it yet.

__________________
http://www.teslascientific.com/

"Knowledge is cosmic. It does not evolve or unfold in man. Man unfolds to an awareness of it. He gradually discovers it." - Walter Russell

"Once men died for Truth, but now Truth dies at the hands of men." - Manly P. Hall
Reply With Quote
Reply

Tags
aether, cosmic induction, energy conference, epd laboratories, eric dollard, eric p dollard, ernst alexanderson, extraluminal, generator, longitudinal, steinmetz, tesla, versor algebra, wireless, dollard, eric

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



Please consider supporting Energetic Forum with a voluntary monthly subscription.

Choose your voluntary subscription

For one-time donations, please use the below button.


All times are GMT. The time now is 12:47 PM.


Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
Search Engine Optimisation provided by DragonByte SEO v1.4.0 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
Shoutbox provided by vBShout v6.2.8 (Lite) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
2007-2015 Copyright - Energetic Forum - All Rights Reserved

Bedini RPX Sideband Generator

Tesla Chargers