PDA

View Full Version : 2014 Energy Science & Technology Conference


Aaron
01-28-2014, 01:27 AM
http://energyscienceforum.com/energyconference2014/2014energyconference.png (http://energyscienceforum.com/energyconference2014)

Registration is now open for the 2014 Energy Science & Technology Conference.

Conference homepage: Energy Science Forum Technology Conference 2014, formerly known as the Bedini-Lindemann Science & Technology Conference (http://energyscienceforum.com/energyconference2014)

Where: Hayden, Idaho (next to Spokane, Washington)
When: June 27, 28 & 29, 2014 (Fri, Sat & Sun)

Speakers:

John Bedini
Eric Dollard
Jim Murray
Paul Babcock
John Polakowski
Aaron Murakami
few others being confirmed...

Jeane Manning will moderate a discussion panel.

BrentA929
01-29-2014, 02:43 AM
Aaron,

What about Peter?


Thanks, Brent

Aaron
01-29-2014, 06:40 AM
Hi Brent,

Peter will be out of town and he has some other projects going on that he has to stay focused on.

Wish he could make it but will still be an awesome conference. There will be a minimum of 3-4 firsts as far as public demos that will be shown that have never been seen before at any conference or public forum.

Aaron
01-29-2014, 06:40 AM
John Polakowski's bio and presentation for the 2014 Energy Science & Technology Conference is updated: Energy Science Forum Technology Conference 2014, formerly known as the Bedini-Lindemann Science & Technology Conference (http://energyscienceforum.com/energyconference2014/#johnp)

BrentA929
01-30-2014, 07:20 PM
Aaron,

Thanks...looking forward to it!


Thanks, Brent



Hi Brent,

Peter will be out of town and he has some other projects going on that he has to stay focused on.

Wish he could make it but will still be an awesome conference. There will be a minimum of 3-4 firsts as far as public demos that will be shown that have never been seen before at any conference or public forum.

Aaron
02-12-2014, 02:19 AM
There are a few updates on the conference page and take note that there is a new domain dedicated to the conference: Energy Science Conference - 2014 (http://energyscienceconference.com)

John Bedini, John Polakowski, Eric Dollard and my own conference presentationdescriptions below our bios have been updated so check them out.

Also, I'm very excited to announce that we have two speakers confirmed that have just cranked the one-of-a-kind status of this conference through the roof! You can see them in the schedule and a preliminary bio and presentation topic. As soon as I have pictures,official bio and presentation topics in hand, I'll announce who they are. You might be able to guess from what I already put in there so it is an understatement to say that this is a conference that you absolutely will want to come to!

Energy Science Conference - 2014 (http://energyscienceconference.com)

After talking to Eric Dollard today, not only is he excited about his own presentation, he is very excited that these other two speakers will be there! Much of that they do is related to Eric's own work and to have all of these people in one room together may not happen for the rest of your life.

We still have a bit over 4 months to go and there are only 132 seats left! Make sure to register now so you can be a part of the event of a lifetime! Energy Science Conference - 2014 (http://energyscienceconference.com)

Sincerely,
Aaron - 2014 Energy Science & Technology Conference

Aaron
02-19-2014, 06:07 AM
William Lyne will be speaking at the conference!

It will be a rare opportunity to spend some time with this legend. He is the author of multiple books including Occult Ether Physics (http://www.amazon.com/gp/product/0985452714?ie=UTF8&tag=maimounas-20&linkCode=as2&camp=1789&creative=9325&creativeASIN=0985452714) and is well known for his work with Atomic Hydrogen Torches.

In several interviews, Eric Dollard has said many of the aetheric concepts that William Lyne shares are valid - much is rooted in the works of JJ Thompson and Tesla. This is a presentation you'll want to see!

You can find his full bio and talk description here: 2014 Energy Science Conference (http://energyscienceconference.com)

Shanjaq
02-19-2014, 06:46 AM
Will you be accepting Dogecoin for registration?

Aaron
02-19-2014, 07:11 AM
Will you be accepting Dogecoin for registration?

I'll be accepting most cryptocoins for just a handful of registrations including Dogecoin. If you want to pay with Dogecoin, please PM me with an email and I'll see what I can do.

Thank you.

SilverToGold
02-19-2014, 10:15 PM
Amazing! Will be looking forward to hearing what Bill has to say!!

William Lyne will be speaking at the conference!

It will be a rare opportunity to spend some time with this legend. He is the author of multiple books including Occult Ether Physics (http://www.amazon.com/gp/product/0985452714?ie=UTF8&tag=maimounas-20&linkCode=as2&camp=1789&creative=9325&creativeASIN=0985452714) and is well known for his work with Atomic Hydrogen Torches.

In several interviews, Eric Dollard has said many of the aetheric concepts that William Lyne shares are valid - much is rooted in the works of JJ Thompson and Tesla. This is a presentation you'll want to see!

You can find his full bio and talk description here: 2014 Energy Science Conference (http://energyscienceconference.com)

qbjorn
02-20-2014, 10:11 AM
William Lyne will be speaking at the conference!


Wow, that's a presentation I'd REALLY like to hear!
His books really made me see the world in a different way.
If I had the chance, I'd sign up for the conference immediately but unfortunately it's not that easy when you're on a different continent.

Aaron, can I hope that you'll be be filming this presentation and make it available afterwards for all of us who wish we could be there?

Aaron
02-28-2014, 08:58 PM
Here is a private forum for conference attendees that have already paid for their seats: Energy Science Forum (http://www.energyscienceforum.com/forumdisplay.php?f=60)

I'll send a password to get in there - please keep it private. The forum will list all members who access it.

This is for early networking so you can get to know some of the other attendees who will be going, business networking, rental car sharing, etc...

This was done at the request of one of the attendees and it's a great idea. I hope that it is helpful.

Aaron
03-15-2014, 01:42 AM
Mark McKay will be presenting at the 2014 Energy Science & Technology Conference. He has new information that sheds some light on Ed Gray's solid state power supply. Energy Science Conference - 2014 (http://energyscienceconference.com)

Aaron
04-30-2014, 11:24 PM
2014 Energy Science & Technology Conference

Formerly known as the
Bedini-Lindemann Science & Technology Conference


Limited to Only 150 People - ABSOLUTELY NO EXCEPTIONS
Only 79 Seats Left!



Even without many updates here on the conference, half the seats are already taken and there are only 2 months left!


There is a NEW conference website, check it out: Energy Conference (http://energyscienceconference.com)


I do want to mention about the updated talk description for Paul Babcock and Jim Murray - you can read it here: Reactive Power as an Energy Source (http://energyscienceconference.com/2014/04/22/paul-babcock-jim-murray-presentation-description/)


Here is what I said about it yesterday in a newsletter:




REACTIVE POWER – REAL “FREE ENERGY” TECHNOLOGY

We’re going to show you a video soon and it will blow your mind! Many of you may be hearing about a global effort to make some Tesla Generator and there is a lot of hype included. To date, there has been ZERO results showing that there is less coming from the power source than the machine is creating.

The video clip that you’re going to see shows more returning to the power source than is leaving and it is very significant! That is the topic of Paul Babcock and Jim Murray’s upcoming talk at the 2014 Energy Science & Technology Conference – here is the description: Paul Babcock & Jim Murray Presentation Description | 2014 Energy Science & Technology Conference (http://energyscienceconference.com/2014/04/22/paul-babcock-jim-murray-presentation-description/)

There are only 82 seats left and when they’re gone, they’re gone! The conference is in 8 weeks so register now because yet again, this is the only conference that you can come to and actually see real “overunity” technology.

Last year, John Bedini showed his famous Bedini SSG, but with a modification. As the output battery charged up, SO THE THE INPUT BATTERY! The wheel was just spinning away and BOTH batteries were charged. That is what you get to see at the Energy Science & Technology Conferences.

Register now: 2014 Energy Science & Technology Conference | Exclusive conference with the Godfathers of the modern day free energy movement! (http://energyscienceconference.com/)

Here is Paul Babcock’s presentation from last year – Magnetic Energy Secrets – part 1 and 2 are on this page: Magnetic Energy Secrets (http://www.emediapress.com/go.php?offer=qiman&pid=33)

By the way, Paul and Jim’s upcoming presentation is based on a four quadrant system like Eric Dollard’s!

Allcanadian
05-09-2014, 04:07 AM
It sounds very interesting and Jim Murray is one person I wouldn't mind having a chat with. In fact I have read all the literature from every person on the list in depth. One of these days I may have to make the journey to attend one of these conferences. Of course I would like to bring a device to demonstrate which raises concerns with the border and all.
In any case, Aaron has done a very good thing here I think in bringing these like minded people together. I can only imagine the brain-storming that goes on behind the scenes. I think that if I could I would some day.

AC

Sputins
06-25-2014, 01:48 AM
Good luck with the Conference Aaron!

I’ll be sad & slightly depressed when it’s on, because I know I’ll be missing out on a once-in- a- lifetime opportunity with the gathering of such spectacular speakers!

I hope all goes according to plan and the Conference is a bigger success than expected.

(I also hope there are no Aether-Farce gate-crashers who might try to spoil the fun).

Aaron
06-25-2014, 06:18 PM
Good luck with the Conference Aaron!

I’ll be sad & slightly depressed when it’s on, because I know I’ll be missing out on a once-in- a- lifetime opportunity with the gathering of such spectacular speakers!

I hope all goes according to plan and the Conference is a bigger success than expected.

(I also hope there are no Aether-Farce gate-crashers who might try to spoil the fun).

Thanks Sputins - it will definitely be an amazing weekend!

I think it will be a nice peaceful event with no troublemakers - a private club in North Idaho is the last place anyone wants to start trouble. ;)

Sputins
07-04-2014, 02:24 AM
Now that the 2014 Energy Science & Technology Conference has concluded, could someone who attended give some kind of overall review, report or feedback from their experience? (Written or otherwise).

What were the highlights? What were the surprises? Anything disappointing? - Any information would be much appreciated!
I’m just looking for someone (no bias) to fill us* in with some information, (or gossip).

*For all of those peeps who missed out and couldn’t make it!

Please do tell! Thanks.

Jiffycoil
07-05-2014, 03:55 AM
I agree with Sputins, are There no members who attended that have reviews or highlights from the conference . The only comment thus far has been how momentous Eric Dollards presentation was. Surely the were other monintous speaches. Any members who were there I would love To hear about your experience.

Aaron
07-05-2014, 07:32 AM
Any of the attendees can confirm or deny what I'm saying but I'll give you my own brief insight. I only mentioned Eric's because quite a few people were asking.

Paul & Jim's was beyond important. They shared where the principles came from in Tesla's work that made the SERPS type technology possible. It's been right there for many years, but apparently hardly anyone has ever figured it out. They both shared much of their background - since Paul's motor patent was finally granted, he showed a test video of the machine producing a COP of about 3.0, which equates to about 250 watts per horsepower. Paul's SERPS replication with his switching was shown back in the exhibit/vendor room and it was operating at a COP of about 50.0 (5000% more work in a resistive load than is drawn from the power supply).

William Lyne's presentation was very interesting - kind of went in a few directions but for the most part, he relayed quite a bit of his background, how he got into a lot of this, and gave his opinions on the origins of the "UFO" technology that many people see. Right when he started to get into the atomic hydrogen technology, I had to leave for a bit so will have to watch it on video when it is edited. He is really quite the gentleman and there were so many synchronicities between us that it was amazing - to me personally of course.

Floyd Rigby and his son went through quite a bit about how his auditing method has saved companies, cities and schools over $720 million and it is MUCH bigger and involved than I thought. He is at the top of his industry and has completely rearranged what I thought utility auditing was all about.

Jeane Manning moderated a discussion panel with most of the speakers. Bedini couldn't take part because of his video agreement with Craddock and Lyne wasn't up on stage with us because when I was gathering everyone together, I didn't know where he was. Quite a few people told some of us that it was actually the discussion panel that "locked it in" for them to know who they're dealing with and not just a bunch of techie geeks - but people who are awake and very conscious about wanting to be very intentional about changing the paradigm of how energy is used in the world today, etc.

Mark McKay shared some new information that came from some recently discovered audio tape conversation with some of EV Gray's investors/engineers but unfortunately, I wasn't able to hear most of it because I was called away for some other business. I know just a bit about what Mark talked about but will have to hear the rest when it is on video.

My own presentations (two of them) were on the Plasma Ignition and Water Fuel and was a bigger hit than I thought. I thought hardly anything would be new to anyone, but to my surprise, it was new for most people in the room so that was good. I showed more of my jet engine project that I never shared publicly including running it with recycled exhaust, plasma, etc. and the propane valve pressure was touching the 0 PSI mark on the scale. Too small to measure with the gauge I had, but is a HUGE difference considering before doing all of that it needed 8 PSI. I debunked every major skeptic's argument against HHO boosters and I ever debunked the proponents of HHO booster claims as to why they work - and I did it with most JPL, NASA, DOE, etc. documentation showing the facts, which are completely indisputable in addition to shining light on what Meyer was really doing that all the Meyer "experts" continue to deny.

Peter Lindemann showed a demo of an SSG that put the spikes to a comparator cap circuit to charge another battery and in that mode, we all know that it is easy to get over 90% recovery in the back battery. When it is switched into "generator" mode, which Bedini shared last year, we had it tuned up so good that the front draw increased by 50% but the output in the caps increased by 100%. So if in normal mode we can get 90% recovery and in this mode, the input goes up by only 50%, yet the output is doubled - well, too many people think they know everything about the SG, but really don't know much about it at all. We were only willing to share so much here but Peter did show a generator coil lighting up 40 white LEDs pretty bright and while doing so, the RPM dropped 0 RPM. We can probably light up several hundred LEDs pretty bright still with 0 drag on the rotor with this method. This was a preview of what is to be explained in the 3rd SG book. I'll repeat - front draw increased by 50% but the output in the caps increased by 100%.

John Bedini revealed quite a bit about his linear current regulator circuits. These are the basic circuit in the new solar charge controllers. On the back end of an SG (designed for the SG), they will convert the spikes to a lower voltage steady direct current. They're very important circuits and John even played an audio amplifier using the same type of circuits that are in the solar charge controllers - you're listening to the current. It is really out of the box. We didn't film this but the same type of presentation on this circuit was already filmed months ago.

John Polakowski gave an awesome presentation on the Cosmic Induction Generator. I missed most of it because I was called away again, but he did go into a lot of very specific details on its operation. There was a demo in the exhibit room. It still has the lower power supply but was still able to show the neutral black spot in the tube between the coils, which is a point of "counterspace", which energy apparently synthesizes right into it. Looks like at one point, the entire tube went black. The filament transformer got fried at one point and smoked and almost set off the fire alarm and sprinklers, but they got it aired out enough for us not to have to evacuate! :suprise: Bedini had a spare one that worked at his shop, some diodes and maybe a cap that made the demo a possibility.

There were plenty of breaks and free time for people to network and spend time with the speakers asking more questions and watching the demonstrations.

Anyway, that is a basic rundown of what was presented. Many people personally told me that it was the best conference they have been to in their lives on any topic. More than one "overunity" device was demonstrated for all to see. We had a full house with people from all over the world - mostly US and Canada. And for me personally, it was quite an honor to sit at the discussion panel with with some of the most brilliant pioneers of the modern day "free energy" movement!

We aim to get 2-3 presentations released by the end of the month.

yaro1776
07-05-2014, 09:22 PM
As an addendum to Aaron's overview of the conference below is my take on this momentous conference.

I had been looking forward to this conference due to the intriguing array of speakers and hints of great revelations - this conference did not disappoint and topped the last two attended.

Day One
1) The first seminar was presented by Floyd Rigby and son on energy audits and their value to larger clients and companies. Truly a very interesting subject matter that, perhaps, could have been covered in half the time allotment since it did become repetitive and interspersed with off point wanderings. Not much there for small home owners and the like. Floyd is an engaging speaker and managed to keep the interest of the audience through most of the time allotted.
2) Next was Mark Mckay who amplified on last year's presentation with additional facts on the E.V. Gray device dating from the 70's. Mark kept the audience engaged with informative historical slides along with a wealth of information on a device that was tested with a COP of 250:1 by big name US labs for verification. In concluding, Mark McKay had an interesting speculation/comment that the electronic circuitry in the Gray appears to be very similar in impact as Bedini's SG. Very good and knowledgeable speaker with a great presentation.
3) Next John Bedini presented the new linear current Solar Tracker with a great example of the internal electronics of the Solar Tracker using it to play music - I was somewhat baffled initially, but slapped my forehead when it dawned on me that we were listening to the current. So the Bedini amplifier circuits have another life. The following Solar Tracker demo showed the unit gathering potential from the Amorphous Solar panels under cloudy and showery conditions. The circuitry is such that the device maintains a given charge voltage level of ~15.1volts to the charge battery and any excess can be directly delivered to another device. John showed a nifty charge circuit using a LED bulb - circuit ( integrated in a Solar Tracker already) will turn an/off the bulb according to set charge voltage threshold. Slick! John B. also used a LiFeP battery that has a high energy density, but without the common problems of a standard lithium ion battery. This appears to be a worthwhile battery advance that is about 1/3 the weight and twice the price of a standard LAB unit.
4) Next Aaron Murakami gave a very thorough presentation on Plasma ignition and presented a detailed look at the progressive improvement in spark through a series of slides and short videos - fascinating stuff. During this segment of the presentation Aaron sprayed a fine water mist onto the plasma spark producing a small flash of light where he claimed that the water was broken down into its constituent elements of hydrogen and oxygen. Whoa!
Furthermore, as an example of the plasma spark capabilities a short video clip showed a standard lawn mower operating with this plasma spark device on straight diesel as a fuel.
The presentation progressed further with uses of HOH from electrolysis as a fuel and its implementation. This portion then segued to Stanley Meyers uses of water as a fuel showing the original water powered dune buggy from the 1970's. Aaron continued to dissect this water as a fuel process and presented a hypothesis as to how this really worked - very well thought out and there may be more to come from Aaron on this entire subject. Aaron speculated that there may be way simpler methods and means for this to be a viable process. Stay tuned to this.
Aaron the progressed to his jet engine design - while it was very interesting and the videos impressive this writer was at the end of his rope from jet lag and the lateness of the hour. Not all was absorbed! I really am looking forward to the video on this presentation since there are some very important points within the subject matter.
End of Day One.

I will continue to the following day Two on Sunday and followed by day Three.
For those who were not present, well you missed a well organized and scheduled lineup of speakers and Demo's. I am still stunned by the information overload and seminars. All the above are my take and understanding of the subject matter presented by the speakers and any errors or omissions are my responsibility.

Later,
Yaro Stanchak
:sun:

BroMikey
07-06-2014, 12:56 AM
Bravo Peter.

Thanks Aaron and ALL for letting us in on the success of that meeting.

There is nobody like YOU!!!:thumbsup:

Mike

Jiffycoil
07-06-2014, 07:15 AM
Thanks Aaron and others for the detailed reviews.

Sputins
07-06-2014, 01:42 PM
Thank you Aaron for the overview, it certainly sounds like it was a fantastic and monumental conference! John Polakowski was lucky that John Bedini could help him out with a filament transformer. (You wouldn't think a filament transformer would likely fry, a plate transformer maybe)? I guess that's one of those little unexpected hiccups that happen. Very kind of JB to help him out.
If many people said that it was the best conference they have been to in their lives on any topic, that is certainly one measure of its success! - Congratulations.

I'm really excited about Eric Dollard's EPIC & historical presentation. Reading what you (Aaron) wrote on the EPD channel gives me goose bumps! I look forward to seeing the video! (Among the others too). I really wish I could have been at the conference in person! Maybe next year?

Thanks Yaro for your review of day one, I certainly look forward to reading about days two and three! I'm sure everyone else is too.

Sputins.

yaro1776
07-06-2014, 10:06 PM
Continuing with yesterday' narrative Day Two was again packed with great information and demo's.

William Lyne woke us all up with his very interesting, and at times, amusing presentation on many unusual, weird bits of info and facts relating to ufo's, nazi collusion during WW2, atomic testing, super submarines, Rosewell aliens, World War two Fu fighters, atomic furnace, etc... Great and engaging speaker that has written several books on his ideas and investigations - truly entertaining with elements of truth and perhaps some grains of salt. His limited supply of books was snapped up quickly, so onto Amazon for a copy...

Next John Bedini brought us back to reality with a comprehensive review and explanation of the SG and the various modes of operation. Very good to hear this again from the master during this show and tell. John again layed out all the schematic diagrams for each mode - 1) Radiant mode, 2) Capacitor mode and 3) Gen mode. John proceeded to add a linear current circuit to the back end of the SG and displayed the operation of this circuit creating a linear direct current that transformed the radiant spikes into a useable form for lighting a super bright LED bulb. He detailed the bi-polar circuit design which doubles the output - bit over my head but the demo was impressive. The kicker here was the little on/off circuit that would turn on the LED when the battery was above a certain voltage threshold - in this case about 15.1v. This presentation by itself was worth the price of admission. The lowly and simple SG has a myriad of untapped capabilities, more as witnessed later by the Peter L presentation. Tip of the hat to JB, you have done it again! Add his two presentations to your DVD collection.

So day two was capped by the much awaited Presentation By James Murray and Paul Babcock on the subject of the SERPS device. The timing/initiation of the Murray \Babcock collaboration is uncertain, but appears to have its roots in the Four Quadrant theory of E. Dollard. This entire presentation, in essence, was based on Tesla's method of recycling electricity. J. Murray in his presentation described and presented documentation of Tesla, mind you under oath, stating that the current energy grid is capable of handling a 5,000,000 gain in power distribution. Power magnification! James M. went on to describe the Dynaflux generator and other hardware related gains that can be realized.
Paul Babcock came into play here describing how modern electronics can replace the older methods of realizing this magnification. So this a marriage of existing technology that has been shown or demonstrated over 30 years ago and now has become a reality. Tesla, the electric zen master, pointed the way nearly a 100 years ago and here we are today reaping the rewards of the Murray/Babcock collaboration, finally showing where Tesla's head was at - some help from Dollard here to clarify the reality of shifting the phase angles between current and voltage. From a broad perspective this seminal seminar and the SERPS demo running in the back room turned the current energy reality on its ear. The rub here is that all this can be explained in classical electrical terms - you go with the flow mon! I will not go into the details of the presentation since the DVD will take care of this - mind you, that this may also become a classic introduction of a new technology...
For further elaboration the SERPS Demo presented an electronic device that was capable of using 1 watt from the power source and successfully lighting at full line voltage two standard resistance light bulbs totaling 50 watts. This yields a rough COP of 50:1 or 5,000%, duh! There may be more with proper tuning...
Could not examine device since it was under two plastic covers - shielding proprietary circuitry - patent is next. Herein lies the difficulty, how do you patent this type of device without creating a tidal wave of opposition? - stay tuned to this device and its progress.
Think Murray, Babcock, Dollard, Polakowski, Murakami, Lindemann and of course, Bedini, who made all of this possible.

Some notes and suggestions here:
The projector arrangement for the computer video feeds was truly inadequate, making it very difficult to see the PPT presentations - get real and improve the setup. Also the screen involved is too small, take the plunge and make it up to par of the subject matter.
The side show in the side room had all the demo's literally in your face during the breaks, most excellent! See it it all - Serps, Bedini SSG, Teslagenix, Energenix and on, and on.

So that is it for Day 2 - truly a mind blowing day event in all its aspects. Day 3 will come in the next installment, fasten your seat belts please.

My take on the conference,
Yaro Stanchak
:sun:

hartiberlin
07-06-2014, 11:28 PM
Any free youtube clips from the conference yet available ?

wantomake
07-08-2014, 02:51 AM
Any free youtube clips from the conference yet available ?

Hartiberlin,
Sorry for being off topic here.

I noticed you come from Germany. Have you any family members alive from the WWII era? If yes do they remember a device that used no battery, fuel of any kind. It was started by pulling a rope like on a grass cutting mower. It was a self running device and would output 300 watts to light several bulbs or a small heater, from the information we have.

There's a group of us trying to replicate this motor generator device called the Lockridge Device. There are some threads(old threads) about it here on this forum. John Bedini and Peter Lindemann have DVD about this device. Our group has been working on this for four years or so. Any old patients or war museums may have something about this also.

Any information would be very helpful.
Thanks,
wantomake

yaro1776
07-08-2014, 01:59 PM
Day Three started with John Polakowski giving a well put together seminar on the Cosmic Induction Generator. Almost like a compressed course in college on the basics of this device and the math behind it. Tesla Coils - the theory, construction and operation - so here we have presented an in depth look at this device and its construction later followed by an actual demo in the nearby display room. More on this later...

John P. stressed that this device is essentially a flat single Tesla coil for the primary and connected capacitor - it always operates as a 1/4 wave circuit - then continued adding the other circuitry elements. Way too complex to handle here, so the video is a necessity if you wish to learn all the details. All in all a very interesting and informative presentation.

The start of the first demo ended in a flash of fried electronics and John went into repair mode with Eric Dollard looking over his shoulder. Later on when all was good. John displayed the operation of the generator while using a short fluorescent light tube to demonstrate the shape of the generated field/lines of force and the dark zone in the center between the antennas/coils. The basic shape of this field was very recognizable with the light intensity varying as it was moved back and forth. Definite black spot in the center when the tube angle was turned from parallel of the centerline of the antennas to perpendicular. Fascinating!

Next Dr. Peter Lindemann gave a very complete seminar on the SSG and its various modes of operation. The demo unit (8 transistor) built for this was very well labeled and completed with instrumentation for voltage and current -very clean setup! In basic mode the wheel (~0.25" gap)was spinning at 365 rpm and drawing 1.35 amps - I missed the amperage going into the charge battery, ouch. Peter elaborated on the performance curves and other basics of design and operation, while stressing the importance of properly conditioning the charge battery.

He then switched the operational mode to generator mode, which he labelled as common ground mode and showed how the capacitor bank functioned in its discharges to the charge battery. During this mode the primary draw increased to ~1.75 amps. One could see the primary voltage remaining stable while the charge voltage was increasing. The Primary input
increased by about 50% while the charge output increased 100%. This is one well tuned SSG... Lindemann stressed that impedance matching is the KEY.

Then onto the the addition of the gen coil. Interesting design in that the internal core of a standard spool was split in half and widened to the width of a standard SSG magnet and then filled with the weld rod core. This was then wound with a 1000ft of #16AWG wire with the assembly mounted to the wheel assembly frame. Not sure of the gap between the coil core and wheel magnets, but the coil was wired to a cap bank and then to a bank of 40 or 48 LEDs using a resistor to control the brightness. Interestingly the inclusion of the generator coil powering the LEDs did not change the SSG RPM. Lindemann explained that it is unknown how many more coils can be added to this arrangement before it impacts SSG RPM and performance. The draw of the LED bank was not quantified.

So the SSG turns out to be one very versatile machine. A well tuned SSG can be tied into a capacitor bank to charge a battery, adding a linear current circuit will create a dc voltage that can light a standard LED super bright and then the addition of one or more modified coils can power small banks of LEDs. You do the math here and it all equals awesome. Thank you Dr. Peter!

So to cap it all off there was a Q and A session for the distinguished speakers and moderated by Jean Manning. A close and personal session where the basic philosophies of all the panel blended into a further push for the advancement of technologies that can change the world we live in for the better.

Then onto the marathon event of Eric Dollard's seminar. So, we all had the immense pleasure of partaking in a stimulating mental onslaught by Eric Dollard on Transluminal power generation. The core of this talk were the differences between Magnetic and Dielectric theory. Eric is a very unique and brilliant scientist who lives in the desert and ponders questions and ideas on transmission line theory and the electrostatic universe. His presentation dealt with the complete history of the development of ac power and radio comm. He dealt with the theories and faults of all the greats such as Maxwell, Faraday etc. Concentrating more on Tesla and his impact on this century. A lot of his 3.5 presentation was way over the head of most of the audience, but he has a wry and deadly sarcastic wit that keeps one engaged.
Eric spoke at length on the theories and equations that he has developed on power transmission along the lines of Tesla's work, this was way over my head and limited knowledge. He provided amusing examples of inadvertent power magnification to illustrate his points. This was a very intense experience from one of the few people on this planet who understands Tesla and his methods of power magnification and generation. He is way out there in his experimentation and tests. He has developed an advance seismic detection and warning system that is currently in operation and build out...
A once in lifetime opportunity to absorb the genius of this man, shunned by the mainstream, but still pushing the envelope. To think that I was there at one of his presentations, whoa!

What else is there to say but thank you to the entire dedicated group of people that made this conference a reality and positive experience. So much to absorb and digest. What can top all this?
:thanks:

My personal take on Day Three and the entire conference,
Yaro Stanchak
:sun:

hartiberlin
07-09-2014, 05:31 PM
Hartiberlin,
Sorry for being off topic here.

I noticed you come from Germany. Have you any family members alive from the WWII era? If yes do they remember a device that used no battery, fuel of any kind. It was started by pulling a rope like on a grass cutting mower. It was a self running device and would output 300 watts to light several bulbs or a small heater, from the information we have.

There's a group of us trying to replicate this motor generator device called the Lockridge Device. There are some threads(old threads) about it here on this forum. John Bedini and Peter Lindemann have DVD about this device. Our group has been working on this for four years or so. Any old patients or war museums may have something about this also.

Any information would be very helpful.
Thanks,
wantomake

Yes, I have old family members, but no one remebers such a device.

Wasn´t the Lockridge device not also a US based invention ?


Well I just read this:
The device was a free energy generator that some German practical genius had made simply by modifying an old automobile generator -- an ordinary generator, not some new, special design! When the allies invaded, an American soldier by the name of Lockridge found this thing running in the basement of an abandoned house powering a bank of light bulbs, but connected to no power source. You started it by pulling a cord wrapped around a pulley on the shaft, just like an old-fashioned power lawnmower, and then it just kept on running.

================================================== =

Would be interesting in what part of Germany it was and who the real inventor was...
Then I could try to find out more...
Was probably only one device built by just one inventor..so not made for sales..

Regards, Stefan.

P.S. No Video clips from the conference floor or the lobby during
chat exchanges ? Did nobody bring his smartphones with him and
recorded there a few clips ?

Aaron
07-09-2014, 07:28 PM
Stefan and all,

Here are a few pics from Jim Murray and Paul Babcock's presentation on the SERPS showing COP 50.0 (5000%) - Jim Murray & Paul Babcock SERPS COP 50.0 (5000%) Presentation | 2014 Energy Science & Technology Conference (http://energyscienceconference.com/2014/07/09/jim-murray-paul-babcock-serps-cop-50-0-5000-presentation/)

Aaron
07-10-2014, 07:20 AM
Free download of the video recording of the discussion panel coming soon...

Here is a bit about the discussion panel - just follow the link on that page:
Free Energy Conference Video Coming | A & P Electronic Media – Digital Publishing by Aaron Murakami & Peter Lindemann (http://emediapress.com/2014/07/10/free-energy-conference-video-coming/)

wantomake
07-11-2014, 08:46 PM
Yes, I have old family members, but no one remebers such a device.

Wasn´t the Lockridge device not also a US based invention ?


Well I just read this:
The device was a free energy generator that some German practical genius had made simply by modifying an old automobile generator -- an ordinary generator, not some new, special design! When the allies invaded, an American soldier by the name of Lockridge found this thing running in the basement of an abandoned house powering a bank of light bulbs, but connected to no power source. You started it by pulling a cord wrapped around a pulley on the shaft, just like an old-fashioned power lawnmower, and then it just kept on running.

================================================== =

Would be interesting in what part of Germany it was and who the real inventor was...
Then I could try to find out more...
Was probably only one device built by just one inventor..so not made for sales..

Regards, Stefan.

P.S. No Video clips from the conference floor or the lobby during
chat exchanges ? Did nobody bring his smartphones with him and
recorded there a few clips ?

Stefan,
So far we heard the device was line produced only in Germany during the war. Nothing here in US like that, at least I've never heard of such. Another member has older friend that remembered seeing one in bunker or cave that regular citizens were hiding in. But he doesn't remember much details.
There was more than one built I believe.

Any information is like gold at this point.
Thanks again,
wantomake

hartiberlin
07-12-2014, 02:34 AM
If that is true, who was the production company ?
If we could have a name, one could do a search on this...
How many should have been built ?
I have studied quite a bit German history, but have never come across such a thing..

wantomake
07-14-2014, 02:22 PM
Stefan,
Thanks for looking and your time.

Nobody has been able to find any information on this device because of the time that has elapsed and I'm sure the US government doesn't want one of these devices to be publicly available.

Can you imagine what will happen IF it does?

wantomake

Aaron
07-15-2014, 05:55 PM
3 testimonials - a lot more in email to be sorted

"I've been to three conferences: 2010, 2013 and 201. This year's conference was the best so far! There isn't even a close second." - Breck

"I drove a total of 3478 miles round trip to attend the convention and was able to personally talk with, and ask questions of, all the presenters. I really appreciated the opportunity for the one on one contact and getting to see the equipment and demonstrations up close and personal! Thanks for holding the convention and thanks to all the presenters! It was time, energy and money well invested." - Gary Hammond

"Enjoyed the conference and was worth the 2700 kms I put on the wife's van. As a fabricator and builder the conference was a bit overwhelming but the connections I made were well worth the trip. I would go again and look forward to your next one." - Jerry Sand

Aaron
07-15-2014, 06:46 PM
TOPICS

FREE Video from 2014 Energy Science & Technology Conference
48 HOURS UNTIL THE RELEASE OF JIM MURRAY & PAUL BABCOCK’S PRESENTATION FROM THE ENERGY CONFERENCE – SERPS COP 47.9 (4790%)!!!!


Hi Friends,


The 2014 Energy Science & Technology Conference was an incredible success! Many are saying it is the most important conference they have been to in their lives from any category of conference.

“I’ve been to three conferences: 2010, 2013 and 201. This year’s conference was the best so far! There isn’t even a close second.” – Breck

“I drove a total of 3478 miles round trip to attend the convention and was able to personally talk with, and ask questions of, all the presenters. I really appreciated the opportunity for the one on one contact and getting to see the equipment and demonstrations up close and personal! Thanks for holding the convention and thanks to all the presenters! It was time, energy and money well invested.” – Gary Hammond

“Enjoyed the conference and was worth the 2700 kms I put on the wife’s van. As a fabricator and builder the conference was a bit overwhelming but the connections I made were well worth the trip. I would go again and look forward to your next one.” – Jerry Sand

FREE Video from 2014 Energy Science & Technology Conference

To view this free video from the conference, you must be a subscriber to the Energy Times newsletter. If you are already a subscriber, you will receive an email with the viewing instructions. If not, go here to watch the video: Energy Times by Peter Lindemann & Aaron Murakami (http://www.emediapress.com/energytimes.php?offer=qiman)



After you click the confirmation link in the email that comes, the first newsletter will have the video link and password. Make sure to give the video a thumbs up to show your support for all the speakers!


48 HOURS UNTIL THE RELEASE OF JIM MURRAY & PAUL BABCOCK’S PRESENTATION FROM THE ENERGY CONFERENCE!


Beginning in two days, the 2014 Conference Film Series will start being released. The first presentation will be the monumental presentation by Jim Murray and Paul Babcock about Jim’s amazing SERPS device. SERPS stands for Switch Energy Resonant Power Supply and is the ultimate in methods for using, storing, and returning electricity to its source!In the first hour, Jim Murray shows the various machines he built and tested over the last 35 years that lead to the understanding of how to build the SERPS device. In the second hour, Paul Babcock explains the theoretical operations of the SERPS system showing how it borrows, uses, and returns electrical power to the source.

The presentation then switches to a clip in the exhibit room where the working model was running and demonstrating 4790% MORE WORK THAN IS SUPPLIED IN NET ENERGY FROM THE POWER SUPPLY – THAT IS A COP OF 47.9!!! It ends with a Q&A by Paul back in the meeting room. A separate PDF file of all of the slides shown in the Power Point Presentation will be included.

Aaron
07-17-2014, 08:57 PM
http://teslaspowermagnification.com/images/secretofteslaspowermagnification300x.jpg

We're honored to be able to release Jim Murray and Paul Babcock's presentation from the 2014 Energy Science & Technology Conference! This is one of the most, if not THE MOST, anticipated video presentation we have ever made available. Jim & Paul teach the science behind the SERPS (Switched Energy Resonant Power Supply) device, which has the highest publicly demonstrated COP's that we know of.

The title of the final presentation release is -The Secret of Tesla's Power Magnification. It's 2 Hours Long and we're even including a PDF of the powerpoint for the presentation so you can see everything up close and clear.

Get your copy now: The Secret of Tesla's Power Magnification by Jim Murray & Paul Babcock (http://www.emediapress.com/go.php?offer=qiman&pid=19)

At the conference - Paul Babcock's replication of Jim Murray's SERPS device using his own patented high speed switching method was producing 52.7 Watts of dissipated energy in two light bulbs while the net draw from the power transformer was only 1.1 Watts! That is a COP of 47.9 or 4790% more energy dissipated in the light bulbs than the net draw from the power supply.

This information represents the first public display and explanation of this technology in all of history. Even Tesla never showed this much about how to accomplish these effects.

Get your copy now: The Secret of Tesla's Power Magnification by Jim Murray & Paul Babcock (http://www.emediapress.com/go.php?offer=qiman&pid=19)

Sincerely,
Aaron @ White Dragon Press

Aaron
07-24-2014, 12:25 AM
TOPICS
ERIC DOLLARD'S PRESENTATION LAUNCHING IN 20 HOURS! PLUS * NEW * INTERVIEW WITH ERIC DOLLARD

Dear Friends,

ERIC DOLLARD'S PRESENTATION LAUNCHING IN 20 HOURS!

In 20 hours, we're launching Eric Dollard's EPIC presentation that he says is his best one ever! It is jammed pack with 4 HOURS of the most thorough history, scientific documentation, and even diagrams of not only wireless transmission systems in general but for electrostatic Tesla and Alexanderson type systems that operate outside of the confinement of the "Speed of Light" - hence, the EXTRALUMINAL reference in the presentation name.

Stay tuned for the announcement!

In the meantime, check out this free *NEW * Interview of Eric Dollard filmed a couple days after the recent conference (make sure to give the video a Thumbs Up to show your support for Eric's work!) -


http://www.youtube.com/watch?v=G5HX9wHU4QE (https://www.youtube.com/watch?v=G5HX9wHU4QE)


Sincerely,

Aaron @ EricPDollard.com

Aaron
07-24-2014, 08:51 PM
* NEW * Extraluminal Eric Dollard Presentation, Includes Lander's Video!

Hi everyone,

We are excited to release the presentation that Eric Dollard says is his best one yet! The Extraluminal Transmission Systems of Tesla and Alexanderson is jam packed with 4 hours of priceless teachings from the master himself.

You will learn not only the history of wireless transmission, but the real science of electrostatic transmission systems that are not restricted to the speed of light. In fact, this is not about "faster than light" but rather INSTANTANEOUS meaning there actually is no velocity! That is why it is called Extraluminal (outside of the speed of light constraints) instead of Superluminal (faster than the speed of light).

Get your copy now: The Extraluminal Transmission Systems of Tesla and Alexanderson by Eric Dollard (http://www.emediapress.com/go.php?offer=qiman&pid=7)

This science was applied by Tesla and Alexanderson and was used by the US Navy in the famous RCA Bolinas station for ship to shore communication back in WWII. Eric Dollard has improved upon the work of Tesla and Alexanderson in this science and has actually build a full scale working model that demonstrates the principles. The primary application was using this electrostatic antenna system to listen to the Earth signals in order to forecast major earthquakes 24-48 hours ahead of time! The best that conventional science can give us is 30 to 60 seconds, which pales in comparison.

You will also learn how the electron models and Einstein's science has been erroneously applied to these systems for all these years. And, you will see the truth in a way that has never before been presented.

SPECIAL BONUS - when you get a copy of this * AMAZING * presentation, you will receive a free bonus download, which is an actual guided tour of the Landers facility, which has never been released to the public before!

Get your copy now: http://www.emediapress.com/go.php?offer=qiman&pid=7 (http://l.facebook.com/l.php?u=http%3A%2F%2Fwww.emediapress.com%2Fgo.php% 3Foffer%3Dqiman%26pid%3D7&h=LAQGK8cH1&s=1)

This presentation is offered at an introductory price, which will expire on July 31, 2014 so make sure to take advantage of this offer now.

Also, if you haven't had a chance to get your hands on Jim Murray and Paul Babcock's presentation The Secret of Tesla's Power Magnification, make sure to get a copy at the discounted price, which will also expire on July 31, 2014.

Get it now: http://www.emediapress.com/go.php?offer=qiman&pid=19 (http://l.facebook.com/l.php?u=http%3A%2F%2Fwww.emediapress.com%2Fgo.php% 3Foffer%3Dqiman%26pid%3D19&h=6AQHLMqFw&s=1)

Sincerely,
Aaron @ White Dragon Press

Aaron
08-06-2014, 01:37 AM
We're finally releasing the Ignition Secrets complete with the VIDEO presentation from the 2014 Energy Science & Technology Conference.
Ignition Secrets by Aaron Murakami has been available only as a book with some demonstration videos but this is the first time there has been an in depth video presentation covering details that are not in the book.

Learn more details based on govt research that shows massive increases in boosting the thermal efficiency of the engine - AND, THIS PACKAGE SHOWS YOU HOW TO BUILD THE PLASMA IGNITION SYSTEM!

Get your copy now: Ignition Secrets by Aaron Murakami | Plasma Ignition (http://www.emediapress.com/go.php?offer=qiman&pid=12)



You're going to get 1.3 GIGABYTES of files that will show you everything you need to build your own and a bunch of demo videos...

You'll see a gasoline engine running on diesel with the plasma - that is how strong and robust this cutting edge ignition system is... a lawnmower running at full speed on only the idle jet... and a bunch of other absolutely incredible demonstrations.

Get your copy now: Ignition Secrets by Aaron Murakami | Plasma Ignition (http://www.emediapress.com/go.php?offer=qiman&pid=12)

And by the way, day after tomorrow, we'll be sending details on some Water Fuel methods based on only air, water and electricity that you haven't seen before! You'll even see my jet engine running strong and the propane pressure gauge needle is on 0 PSI.


Sincerely,
Aaron Murakami
Ignition Secrets

BroMikey
08-06-2014, 02:10 AM
We're finally releasing the Ignition Secrets complete with the VIDEO presentation from the 2014 Energy Science & Technology Conference.
Ignition Secrets by Aaron Murakami has been available only as a book with some demonstration videos but this is the first time there has been an in depth video presentation covering details that are not in the book.

Learn more details based on govt research that shows massive increases in boosting the thermal efficiency of the engine - AND, THIS PACKAGE SHOWS YOU HOW TO BUILD THE PLASMA IGNITION SYSTEM!

Get your copy now: Ignition Secrets by Aaron Murakami | Plasma Ignition (http://www.emediapress.com/go.php?offer=qiman&pid=12)



You're going to get 1.3 GIGABYTES of files that will show you everything you need to build your own and a bunch of demo videos...

You'll see a gasoline engine running on diesel with the plasma - that is how strong and robust this cutting edge ignition system is... a lawnmower running at full speed on only the idle jet... and a bunch of other absolutely incredible demonstrations.

Get your copy now: Ignition Secrets by Aaron Murakami | Plasma Ignition (http://www.emediapress.com/go.php?offer=qiman&pid=12)

And by the way, day after tomorrow, we'll be sending details on some Water Fuel methods based on only air, water and electricity that you haven't seen before! You'll even see my jet engine running strong and the propane pressure gauge needle is on 0 PSI.


Sincerely,
Aaron Murakami
Ignition Secrets

You ain't kiddin Aaron

That stuff is incredible. I have been wondering when the time would come for you to release more of a collective package. Thanks so much for being there and for puttin up with the likes of these people who never have anything good to say thinking it is another scam.

This stuff is real and if people have their minds made up you can't help them.

Thanks for the great work on the jet and the lawnmower that takes so little energy to run on water using the ignition plasma stuff.

Keep it up.:thumbsup:

Mike

Aaron
08-06-2014, 04:58 AM
You ain't kiddin Aaron

That stuff is incredible. I have been wondering when the time would come for you to release more of a collective package. Thanks so much for being there and for puttin up with the likes of these people who never have anything good to say thinking it is another scam.

This stuff is real and if people have their minds made up you can't help them.

Thanks for the great work on the jet and the lawnmower that takes so little energy to run on water using the ignition plasma stuff.

Keep it up.:thumbsup:

Mike

Thanks for the kind words Mike!

It is definitely real and I even give some powerful references from NASA, etc... who are saying the same thing.

With my jet engine, I show a video in the Water Fuel Secrets package coming out day after tomorrow where it is running but the propane pressure is on 0 psi - doesn't mean no propane, but just a trickle too small to measure on that gauge. To give you an idea, before recycling exhaust or using plasma, etc... for the exact same regulator/valve, it took 8 psi just to get it to idle. By the time I was done, the needle is on 0 which I believe it means it is somewhere in the neighborhood of 0.1 to 1.0 psi. Even at 1 psi that is a HUGE reduction.

And, I didn't even try to modify the steam with the RF yet but I already have those amazing results!

BroMikey
08-06-2014, 08:15 AM
Thanks for the kind words Mike!

It is definitely real and I even give some powerful references from NASA, etc... who are saying the same thing.

With my jet engine, I show a video in the Water Fuel Secrets package coming out day after tomorrow where it is running but the propane pressure is on 0 psi - doesn't mean no propane, but just a trickle too small to measure on that gauge. To give you an idea, before recycling exhaust or using plasma, etc... for the exact same regulator/valve, it took 8 psi just to get it to idle. By the time I was done, the needle is on 0 which I believe it means it is somewhere in the neighborhood of 0.1 to 1.0 psi. Even at 1 psi that is a HUGE reduction.

And, I didn't even try to modify the steam with the RF yet but I already have those amazing results!

Yeah Aaron I have been wondering who would come forward first with the hard data. All of this testing and building takes time and your research should help some who don't have as much time to re-invent all of the wheels.

I seems like I remember you either saying 0 on the gauge or I saw one video like that. The reason I got fired up:D about the subject is because every year I have to break my back picking up huge amounts of wood to burn heating this old farmhouse and I am getting near the end of my rope there. So I thought if Aaron and Peter can run a lawnmower on a 47uf cap at 160vdc maybe I could go up alittle in power to say 5000uf at 160vdc using 30-40 of the little burn chambers:thinking: still trying to think it up.

That way maybe a few hundred watts could heat the house?

I think it is possible. Ill bet that jet wouldn't need to come on that much to heat up a house huh? And with only a trickle of propane and a few watts of RF I would truly be stylin.:thumbsup: It is a very exciting thought for me not just for me but for those who will freeze this winter.

Mike

Aaron
08-21-2014, 04:42 AM
We are releasing the Conference Video Series #4, which is Water Fuel Secrets. This shows you the reality of on-demand water fuel using nothing more than air, water and electricity.
Read what's on this website! Water Fuel Secrets by Aaron Murakami (http://www.emediapress.com/go.php?offer=qiman&pid=13)


Many people heard of Stan Meyer and his water fueled dune buggy, but almost everyone has met with failure because they think he was running his car on electrolyzed water gas when he was not! And this is well known by a few of our friends who actually knew Stanley Meyer so you're getting the inside scoop...

Electrolyzed water gas is only one of the ingredients necessary to create his on-demand SYNTHETIC GAS, which is completely contrary to what nearly all the self-proclaimed Stan Meyer experts are claiming. Many people debate this, but in Water Fuel Secrets, you see indisputable proof that this is EXACTLY what Stan Meyer is saying in his own words.


You'll also see my jet engine running strong while the propane pressure gauge is on 0 PSI! That is the results I get by applying this information and I'm only using a few of the steps.

You'll learn the reality to how hydrogen fuel supplementation really works as well as what Stan Meyer was really doing to create his on-demand water fuel - this Water Fuel Secrets package will transform your understanding about water fuel technologies.

Read what's on this website! Water Fuel Secrets by Aaron Murakami (http://www.emediapress.com/go.php?offer=qiman&pid=13)

Go check out what is included in this package including the Free Bonus!

Sincerely,
Aaron

Aaron
08-21-2014, 04:43 AM
http://evgrayrevealed.com/images/graymotor.jpg (http://www.emediapress.com/go.php?offer=qiman&pid=55)

(http://www.emediapress.com/go.php?offer=energetic4&pid=55)Mark McKay's presentation from this year's conference is now available!

This year's talk is Part 2 to The Real History of the Ed Gray Motor.

It includes transcripts from some audio cassette tapes that were recently found by an old associate of Ed Gray. They are interviews with Ed Gray's chief engineer Richard Hackenberger. Details are shared about the power supply that Gray used in his motors and camping lanterns.

If you don't have part 1, you can get both at a discount. Peter and I are also putting together some other bonuses that will be included in this package at a later time and will be available to anyone that purchased Part 2 or the combo without charge.

Go here now: The Real History of the Ed Gray Motor by Mark McKay, E.E. (http://www.emediapress.com/go.php?offer=qiman&pid=55)

Aaron
08-27-2014, 05:48 AM
http://cosmicinductiongenerator.com/images/cosmicinductiongeneratorbanner.jpg (http://www.emediapress.com/go.php?offer=qiman&pid=56)

ANNOUNCING PART 7 OF THE 2014 ENERGY SCIENCE & TECHNOLOGY CONFERENCE SERIES

The Cosmic Induction Generator is a very important technology with many applications, but the first goal was to demonstrate the manifestation of visible evidence of the intrinsic formative forces of the universe, which is done in the spirit of Tesla technology.

The Tesla Transmitters are designed to replicate the ideas expressed in Wilhelm Reich's "Cosmic Superimposition" of formative fields. When two living energy fields mutually interact, they can stimulate each others' excitation to the point of illumination - in other words, CREATE LIGHT!

Get your copy now: Cosmic Induction Generator by John Polakowski (http://www.emediapress.com/go.php?offer=qiman&pid=56)

You'll be getting a 72 minute, in-depth presentation explaining the history and science of the Cosmic Induction Generator and it's use as a study aid for the "etheric formative forces" of the Electrical Universe. Also included are complete schematics and circuit characteristics based on Eric Dollard's "transmission line" theory of operation.
There is also quite a bit of Q & A throughout the presentation - John answers a LOT of questions!

As a bonus, you'll even get over 180 MB of photos of John Polakowski & Eric Dollard working on the CIG at EPD Laboratories and three videos about the CIG that have already been put on YouTube but are included for your convenience. They are interviews with Eric, John with some video of them working on the CIG.
Get your copy now: Cosmic Induction Generator by John Polakowski (http://www.emediapress.com/go.php?offer=qiman&pid=56)

Sincerely,
Aaron

Aaron
09-11-2014, 12:17 AM
FREE VIDEO - 2014 Energy Science & Technology Conference Panel Discussion video - open free to public now. https://www.youtube.com/watch?v=-JJpGhgqu6A

RELEASES FROM THIS SUMMER THAT ARE AVAILABLE NOW

The Secret of Tesla's Power Magnification by Jim Murray & Paul Babcock
The Secret of Tesla's Power Magnification by Jim Murray & Paul Babcock (http://www.emediapress.com/go.php?offer=qiman&pid=19)

The Extraluminal Transmission Systems of Tesla and Alexanderson by Eric Dollard
The Extraluminal Transmission Systems of Tesla and Alexanderson by Eric Dollard (http://www.emediapress.com/go.php?offer=qiman&pid=7)

Dynaflux Alternator by Jim Murray
Dynaflux Alternator by Jim Murray (http://www.emediapress.com/go.php?offer=qiman&pid=6)

Ignition Secrets by Aaron Murakami
Ignition Secrets by Aaron Murakami | Plasma Ignition (http://www.emediapress.com/go.php?offer=qiman&pid=12)

Water Fuel Secrets by Aaron Murakami
Water Fuel Secrets by Aaron Murakami (http://www.emediapress.com/go.php?offer=qiman&pid=13)

Tesla's Ideal Flying Machine by William Lyne
Tesla's Ideal Flying Machine by William Lyne (http://www.emediapress.com/go.php?offer=qiman&pid=47)

The Real History of the Ed Gray Motor Part 2 by Mark McKay
The Real History of the Ed Gray Motor by Mark McKay, E.E. (http://www.emediapress.com/go.php?offer=qiman&pid=55)

Cosmic Induction Generator by John Polakowski
Cosmic Induction Generator by John Polakowski (http://www.emediapress.com/go.php?offer=qiman&pid=56)

sprocket
09-11-2014, 04:45 PM
FREE VIDEO - 2014 Energy Science & Technology Conference Panel Discussion video - open free to public now. https://www.youtube.com/watch?v=-JJpGhgqu6A

That's one interesting little tit-bit of video-information about JLN that I had always suspected! For the uninitiated, Jean Louis Naudin, whom many regard as the French Patron-Saint of free-energy, is actually financed to find what works in open-source FE, then he/his-backers quietly patents it, preventing anyone else from commercialising them. Adding no doubt to the 5000+ other patents that will never be allowed commercial exploitation.

That also strongly suggests that stuff with real potential will never make it to his web-site at all. His Kapanadze 'replication' was a joke that he suckered a lot of people (and me) into replicating - after stringing us along for months, he then introduced a more expensive piece of kit which showed that this 10-20 COP was actually measurement-error after all! So he's into dis-info/misleading as well.

Aaron
11-18-2014, 02:19 AM
The entire conference website has been updated and organized.
Energy Conference (http://energyscienceconference.com)

BroMikey
11-18-2014, 07:32 AM
Nicer layout dude.:thumbsup:

Mike


The entire conference website has been updated and organized.
Energy Conference (http://energyscienceconference.com)