PDA

View Full Version : New permanent magnet motor video


amigo
10-17-2007, 12:49 AM
Saw this on overunity.com and I have a feeling this fellow might be on the right track.

YouTube - Magnet Motor Prototype (http://www.youtube.com/watch?v=jZjEYu9BbW0)

The problem I have seen with all permanent magnet motors so far is that everyone keeps thinking in two dimensions which is a big shortcoming.

This fellow has expanded into the third dimension and you can already see improvement over those two dimensional spiral motors.

I would take this a few steps further (or turn it up couple of notches :) ). Instead of a cylinder use an inverted cone (apex down) so that we have a vortex/spiral, and pieces on the cone are constantly spiraling or "falling" down into the vortex. I remember reading about David Hamel and his revelations where he said that his device is all about being out of alignment and constantly "falling" so that clicked in right away after seeing this.

Peter Lindemann
10-17-2007, 04:18 AM
Saw this on overunity.com and I have a feeling this fellow might be on the right track.

YouTube - Magnet Motor Prototype (http://www.youtube.com/watch?v=jZjEYu9BbW0)

The problem I have seen with all permanent magnet motors so far is that everyone keeps thinking in two dimensions which is a big shortcoming.

This fellow has expanded into the third dimension and you can already see improvement over those two dimensional spiral motors.

I would take this a few steps further (or turn it up couple of notches :) ). Instead of a cylinder use an inverted cone (apex down) so that we have a vortex/spiral, and pieces on the cone are constantly spiraling or "falling" down into the vortex. I remember reading about David Hamel and his revelations where he said that his device is all about being out of alignment and constantly "falling" so that clicked in right away after seeing this.

Amigo,

This is very interesting. It certainly represents a new and different method for a permanent magnet motor. If you are interested in this idea, I highly recommend that you first try to DUPLICATE the design shown in the video clip. IF you can get it to run, THEN you should think about modifying it or improving it.

There are still a few unknowns. We don't know what magnets he used or the polarity he used to face the screws. Did he use all the same poles facing the screws, or did he alternate the poles? Or did he face the edge of the magnets to the screws, with the poles facing each other?

The idea seems simple enough to work with.

Good find!

Peter

Aaron
10-17-2007, 05:03 AM
Stefan Marinov had an "infinitely long Siberian Coleiu (spelling???) magnet".

Infinitely long seems to be the same concept of "constantly falling"

amigo
10-18-2007, 12:38 AM
Aaron, this must be it, will take a read at the paper: Coliu (http://digilander.libero.it/altraenergia/marinov/coliu.html)

Peter, I usually try to visualize something and at the same time recollect things I have seen, heard or read from the past that might apply to the task at hand.
This process is seemingly transparent for me most of the times, and so I see it as a gift - being able to connect abstracts that at first sight do not have anything in common.

Though I'm not Tesla who could visualize a machine in his mind, set it up and let it run until it breaks, then figure out why it broke and make his physical design with corrected parameters, thus succeeding with it the first time around. :)

Damien
10-18-2007, 09:52 AM
YouTube - How to Power Your Car Using Magnets - HacknMod.com (http://www.youtube.com/watch?v=6LAUAsIosjc&NR=1)

Check out this video for an upgrade of that same device

BroMikey
07-11-2014, 06:34 PM
HoJo Motor A Working Free Energy Machine - BANNED FOOTAGE! - YouTube (http://www.youtube.com/watch?v=3uecsqxtimo)


Mag Motor video. I have been seeing this type of free energy demo for 40 years now with no end in sight. I am sure one exists some where.

Even displaying the principle operation as demo is very threatening to the big oil cartel.

This vid must be from waaaay back when with most of us sitting on the fence.

That is WILTS not Witts sorry.

Keep Duckin:thumbsup:

Mikey

TheoriaApophasis
07-12-2014, 10:25 AM
[url=http://www.youtube.com
Mikey

That motor wont work

Why? because at high speed the mutual induction will create slippage and the whole thing will fly apart (or shake like an earthquake).


You cannot make a machine that works off centrifugal and centripetal field reciprocation, rather only one that runs off of (.......X.........) no comment. :D


Id give him $100 to run it even at 60 RPM, much less 100, it would slip and shake like Hades warmed over.


That machine will "operate" beautifully at VERY LOW RPM, otherwise its a steaming pile


You have to understand magnetism before you can use it properly. :D

http://kathodos.com/hand.jpg

Netica
07-12-2014, 01:24 PM
Just like to say that every kind of magnet motor that I have tried to build, and there's been a few, have always balance themselves out. Not that I've tried everything by any means, but whatever I've done forces just end up equalizing.

Stealth
07-12-2014, 05:23 PM
I, too have built many magnetic motors. Almost all have equalized after a brief running period. Only two prototypes have caused me to reevaluate what is happening and why. Both use magnetism and gravity working in unison to propel the machines. I think a pure magnetic motor is possible given the correct alignment and dimentions. But I also feel that a combo motor is more practical, using magnetic and another energy source to compliment each other. I am now designing a new motor to utilize these energy forces to enhance the power and adding to the magnetic power already inherent in the magnets. I have two such machines on the drawing board(cad) as we speak. With some tweaking and experimenting, it should be very possible to get one, if not both up and self running. Both use the same concept but very different configurations. Only after I build a prototype will I know their limitations and parameters. I have hope that, at least one will be feasible as a self running motor. One will be very simple to build, while the other one will require major machining and strict tolerances. Good Luck with your designs. Stealth

TheoriaApophasis
07-12-2014, 06:39 PM
I, too have built many magnetic motors. Almost all have equalized after a brief running period



Thats because you (and everyone else also) think they're messing with magnets when they use "magnets"

they aren't. Whats that mean?

It means any and all magnets you ever had your hands on are electrified dielectric objects with (under perfect conditions) a ratio of 3.23606 units of dielectricity to 1 part magnetism. At 90 degrees from any "pole" around the center is the inertial plane , or dielectric 'flywheel'.


Everyone is 'looking' at the precessing and reciprocating axes of a magnet, just like someone who can only see the precessing axes of a gyroscope but is utterly ignoring the giant spinning flywheel at 90 degrees to the precessing axes.

See the book for reference. https://archive.org/details/magnetism1small

boguslaw
07-12-2014, 07:39 PM
I, too have built many magnetic motors. Almost all have equalized after a brief running period. Only two prototypes have caused me to reevaluate what is happening and why. Both use magnetism and gravity working in unison to propel the machines. I think a pure magnetic motor is possible given the correct alignment and dimentions. But I also feel that a combo motor is more practical, using magnetic and another energy source to compliment each other. I am now designing a new motor to utilize these energy forces to enhance the power and adding to the magnetic power already inherent in the magnets. I have two such machines on the drawing board(cad) as we speak. With some tweaking and experimenting, it should be very possible to get one, if not both up and self running. Both use the same concept but very different configurations. Only after I build a prototype will I know their limitations and parameters. I have hope that, at least one will be feasible as a self running motor. One will be very simple to build, while the other one will require major machining and strict tolerances. Good Luck with your designs. Stealth

Congratulations :thumbsup: This is the correct approach I'm sure. However I still think magnetic motor is not much usable due to costs per output power...

BroMikey
07-12-2014, 08:07 PM
@Boguslaw

@Stealth

@ Theo

Here is a vid of magmotor just simple magnets on an angle. I have never seen such a simple arrangement that produces power for free.

Free Energy Magnet Motor fan used as Free Energy Generator "Free Energy" light bulb - YouTube (http://www.youtube.com/watch?v=jiAhiu6UqXQ)

If a set of magnets could be put on any fan blade you could have a free fan.

Is this possible? Has anyone used magnets like this?

Mike:)

This one is big NO scam (it's a REAL DEAL) Muammer Yildiz Magnet Motor demo at Delft University - YouTube (http://www.youtube.com/watch?v=mHW6b1aFPfU)

TheoriaApophasis
07-12-2014, 08:20 PM
[SIZE="3"]@Boguslaw


Free Energy Magnet Motor fan used as Free Energy Generator "Free Energy" light bulb - YouTube (http://www.youtube.com/watch?v=jiAhiu6UqXQ)




yes, that Indian guy and his watch batteries taped to the side of the fan motor. Either than or an induction field under the table.

Ive seen that bogus video a few times.

Some people send me links to that video.


He should become an illusionist :rofl: :rofl:


HE MAKES A HUGE MISTAKE AT 2:17 ON THE VIDEO, where you can see the fan blades stop moving VERY QUICKLY, hes got it powered externally

Field pressures always find equalization, you can build one yourself, it wont work.

BroMikey
07-12-2014, 08:27 PM
Thanks Theo

Here is the secret of magmotors

I think?

Self Running Magnetic Motor Stator Test #2 update - YouTube (http://www.youtube.com/watch?v=QLufUUpqNgU)

See the speed of acceleration.

Is this a fake? Is everything a fake?

Mike

Free Energy Selfrunning Magnet Motor ??? - Fact or Fake ? Wasif
Kahloon challenge to the engineers - YouTube (http://www.youtube.com/watch?v=lCMuDBajFjU)

Discovery Of Magnetic Shielding For All-Magnet Motor. The Holy Grail Of Free Energy. - YouTube (http://www.youtube.com/watch?v=14ayyu9PVSI)

TheoriaApophasis
07-12-2014, 08:33 PM
also fake, Ive seen that one before.



THIS ONE IS REAL:
https://www.youtube.com/watch?v=b-MSiQTXIG0


however he doesnt understand WHY he needs to have a missing magnet :p

AND what 'destroys' his experiment is that he keeps having to move his tube which is inducing counter precession to the reciprocating fields of the magnet on the table. :rolleyes:

He has to create precession to get the 'results' he thinks is power generation.



THIS ONE IS REAL TOO:
https://www.youtube.com/watch?v=rZIrTUenGAE

I mess around a lot with pyrolytic graphite

however at PERFECT design (which his certainly is NOT), you might get only a very few milliwatts out of it.

BroMikey
07-12-2014, 08:54 PM
Thanks Theo I am collecting your input

Magnetic gates. John Bedini has a seminar on DVD and people would be better off watching that first.
:thumbsup:
Discovering Magnetism Magnetic Gates Howard Johnson) (2006) - YouTube (http://www.youtube.com/watch?v=XqTFgX4YA0c)

Mike PS I Am watching John B right now talk magmotors howard Johnson

wrtner
07-15-2014, 04:30 PM
@Boguslaw

@Stealth

@ Theo

Here is a vid of magmotor just simple magnets on an angle. I have never seen such a simple arrangement that produces power for free.

Free Energy Magnet Motor fan used as Free Energy Generator "Free Energy" light bulb - YouTube (http://www.youtube.com/watch?v=jiAhiu6UqXQ)




Some devices can act as either a motor or generator.

None of my computer fans, when mechanically spun, generated a voltage. I doubt the rest of this video.

ewizard
07-16-2014, 05:19 PM
yes, that Indian guy and his watch batteries taped to the side of the fan motor. Either than or an induction field under the table.

Ive seen that bogus video a few times.

Some people send me links to that video.


He should become an illusionist :rofl: :rofl:


HE MAKES A HUGE MISTAKE AT 2:17 ON THE VIDEO, where you can see the fan blades stop moving VERY QUICKLY, hes got it powered externally

Field pressures always find equalization, you can build one yourself, it wont work.

Yes - that - and you notice he never hooks up the light to the fan and then spins it up which would slowly bring up the brightness if it was real. That is because simply hooking the wires to the light would turn on the light as the light bulb probably has a battery inside the base and simply hooking the wires together on it would turn it on. Output wires from fan are probably just shorted together. You first clue this is fake should be that he has an East Indian accent. Not sure why but there are a whole lot of fake energy videos from guys with that accent :rofl:

TheoriaApophasis
07-16-2014, 07:38 PM
Not sure why but there are a whole lot of fake energy videos from guys with that accent :rofl:


I know why, I translate ancient Pali (a prakrit) texts, and Indians have been FAMOUS for many 1000s of years for having "magic tricks".

The "Saddhus magic"


its used by traveling saddhus to impress the dumbz people to toss a coin or some food into their pot. :rofl:


Indians love "cool magic" like Americans love watching the Superbowl

BroMikey
07-16-2014, 07:41 PM
Some devices can act as either a motor or generator.

None of my computer fans, when mechanically spun, generated a voltage. I doubt the rest of this video.

Hello Wrtner

Any coil with a magnet passing by it will produce power IF a capacitor is installed in parallel across the winding. I am not sure how he did it but I can tell you it works.

One day I took an old washer motor and spun it up to speed. It didn't put out any power so I put an old run cap across the leads. First a 45uf oil filled 370vac.

It produced about 2 amps before failing and what would have is it would stop generating even though it was still being turned so I had to unhook the load for a second.

There is went again, it generated the 1-2 amps without dropping out.

Next I added more in parallel til I had several hundred uf.

I pulled the full rated amount of 9 amps from it to use an electric chainsaw out back in the woods.

It is a motor rated at 9 amps 120vac but I use it to generate power.

Type in Motor/generator on the web and you will see videos and more than what I had to work with.

Everyone is doing that now.

I did it 20 years ago.:thumbsup:

I think normally those little pc fan motors have a circuit but it can be bypassed with easy and made to generate.

There is a guy who rewired one to make a JOHN BEDINI ENERGIZER.

So yes I think you are right modifications are needed to get the tiny motor to make 1 vdc.

My question about the video is "can magnets turn the fan blade in that arrangement" it has a magnet on every blade on an angle (Plain and simple) then a magnet above sends the thing spinning.

What I did consider was the possibility of the dual magnet arrangement. Magnets in the motor and on the fan and maybe they are spaced just right (By accident) causing a double action to the drive magnet.

Mike

BroMikey
07-17-2014, 08:26 PM
HoJo Magnetic Motor - BEST Alternative Energy, AMAZING! - YouTube (http://www.youtube.com/watch?v=CjiDTHJCzGA)




The Steorn Magnetic Motor - could it power your home for free? In this article, I will tell you more about Steorn the company and their development of a free energy device. I will explain why I believe that Steorn's products really can revolutionise the world in the near future and how you can start powering your home for free without having to wait for the first Steorn commercial unit to hit the market.

History Of Steorn And Their Development Of Magnetic Motor Technology

Steorn is a company based in Dublin, Ireland that over the last few years generated a lot of buzz and chat in the industry and on the internet as their publicity machine has gained traction.

Steorn has been developing free energy magnetic motor technology since 2003. In 2009, they invited engineers and companies to become part of their development group and also successfully demonstrated their e-Orbo magnetic motor to the public. Their YouTube channel contains several demonstrations and evidence that the devices are working properly.

What sets Steorn out from the crowd is their very corporate approach to magnetic motor technology which has previously attracted mostly garage workshop hobbyists with only a few poor commercial efforts.

How Does It Work?

Steorn explains on their web site that their motor is the result of over-unity technology. Over-unity technology is an area of fringe physics that does not obey the conventional laws of physics that we have come to take for granted.

Using the magnetism contained within standard magnets, their repelling force can be used and converted into rotary motion. This can then be converted into electricity for immediate use, storage or transmission to elsewhere.

How To Generate 7 Kilowatts Without Waiting For Steorn

Within five years time, Steorn will have probably brought this technology to market either directly themselves or via partners. But what if you don't want to wait that long to stop paying power bills?

One option is to pay ?419 to gain access to Steorn's knowledge development base (SKDB). Whether this will give enough details for you to create your own motor quickly is not clear.

A better alternative is to do what many thousands of others are doing every day - make your own magnetic motor. The beauty of this technology is that it is so incredibly simple and little more than a rotor, some strategically placed magnets and basic wiring. All you need is some tools.

ZERO POINT MAGNET GENERATOR Cheap Alien Alternator Barack Camelot Clinton Cloak Energy Free Generator George Green HHO Hamel Hilary Hydrogen Invisible Larry Lawrence Machine Magnet Magnetic Magnetism McCain Motor Obama Overunity Paul Perendev Potomac Project Shielding TESLA Tesla Time Travel UFO Xpenzif anti anti-gravity antigravity aviation car cavity clean coils computer effect electric energy engine environment field free gas gravitons

BroMikey
07-19-2014, 07:49 AM
Self Running Magnetic Motor Stator Test #2 update - YouTube (http://www.youtube.com/watch?v=QLufUUpqNgU)

One Way Magnetic Shielding - Is Indeed The Holy Grail - YouTube (http://www.youtube.com/watch?v=IlMBZJEtwRQ)

Published on Feb 19, 2013

Updates, FAQ's and Reports Now Archived at:
Stator Pro, Magnetic Engine Technology (http://www.StatorPro.com)
James Roney Stators, Up and Personal (http://www.JamesRoneyStators.com)
Pleaseee pass the links around. Thanks a million!
________________________________________

Request from Youtuber for an improved stator test as to better examine the dynamics of the imbalance in the James Roney One Way Magnetic Stator. Results are genuine and thus have not been faked.

Magnets used in this video:
N42 Neodymium Magnets - 1"x1"x1/4"
N42 Neodymium Magnets - 1" round by 1/4" thick
N42 Neodymium Magnets - 2"x4"x1/4" buried inside of stator
Opposite poles of attraction are used in this demonstration.

No tricks of any kind were used in the making of this video.

FREE MAGNETIC ENERGY - OPEN SOURCE. (http://www.FreeMagneticEnergy.info)

Is a self-running magnet motor possible??? Is my one way magnetic shielding technique the Holy Grail to making a running magnet motor??? I simply don't know one way or the other until all tests are exhausted. That's why I'm exploring all avenues. By the way, my work has absolutely nothing to do with perpetual motion.

SPECIAL NOTICE: A con artist is someone who intentionally lies to someone to swindle/scam them out of something for monetary/financial gain. Someone who gives away free information is no more a con artist then someone who gives away FREE food samples in a grocery store. All my info is 100% FREE and 100% OPEN SOURCE. I'm just someone having fun playing with magnets who shares their findings and insights with the public. Anyone who accuses me of being a con artist amounts to nothing more than reckless, ignorant and unsubstantiated allegations and will be banned.


________________________________________*___
SPECIAL NOTE TO KNOWITALLS:

First... a big THANK YOU! ...to all those who have given me 'constructive" feedback and encouragement in the continued research and development of free energy via magnetism. Sadly there are those out there who feel it's their duty to lie and mislead you about my research. To set the record straight, my work has nothing to do with perpetual energy as magnets don't last forever. Nor does my work have anything to do with V-gates, Bedini motors or what have you. Rather my work is about magnetism itself and how one might build a motor that uses only magnets to run without any magnet wire of any kind.
Formally stated; Newton's third law is: For every action, there is an equal and opposite reaction; in this case, magnetic forces. My objective is simple: "To overcome the cause and effect between two opposite poles where not all of the net gain from the initial attraction is totally lost by an equal and opposite attraction."
Because of all the lies, false claims and accusations made against my simple experiments with magnets, I feel it's best that I turn off comments. However I have left the negative comments and ignorant attacks on my work so as you can easily identify the culprits and flamers that caused me to turn off comments in the first place. You have my permission to "have at them" on my behalf via their channel.
Lastly, I currently work from 8:30 AM to 10:00 PM, seven days a week ever since early 2013. Thus I've no time for magnets right now. That will drastically change in early 2014 once I retire from my job.

If you CAREFULLY replicate my work, you will discover what I have revealed in my videos 'actually works' the way it works in my videos. Rather than attack my work, do it yourself and then you will see my research and results are as real as it gets. Otherwise bug off and don't come back.
*By the way, I have nothing for sale. Never did. All the info is "OPEN SOURCE" only that I claim Copyright to my videos itself and not the information or contents contained within, thus my videos my NOT be used to make money from on YouTube or elsewhere without written permission. I do NOT have a working prototype at this time, nor have I ever had an actual working prototype.



Cheers!

James Roney Stators

Duncan
07-19-2014, 06:17 PM
As I recall steon .. 200 kits were issued to interested academics world wide who replicated the device, this then was the promo video https://www.youtube.com/watch?v=PFZS-UMN1lk we don't have the device so I guess tptb prevailed .... again :mad:

BroMikey
07-19-2014, 07:52 PM
As I recall steon .. 200 kits were issued to interested academics world wide who replicated the device, this then was the promo video https://www.youtube.com/watch?v=PFZS-UMN1lk we don't have the device so I guess tptb prevailed .... again :mad:


Ireland is to close to the Queen of England. The suppression is everywhere so we will have to use our heads to implement and infiltrate so as not to ruffle any feathers.:rolleyes:

Mike

BroMikey
07-21-2014, 05:28 AM
http://pesn.com/2010/07/31/9501681_Revealing_What_I_Know_About_Building_the_P erendev_Magnet_Motor/Photos/mike_brady_assembling_perendev_rotor2_crop.jpg




http://pesn.com/2010/07/31/9501681_Revealing_What_I_Know_About_Building_the_P erendev_Magnet_Motor/Photos/perendev_motor_edge_800w.jpg




http://pesn.com/2010/07/31/9501681_Revealing_What_I_Know_About_Building_the_P erendev_Magnet_Motor/Photos/perendev_motor_assembled_susan_carter_witness_full .jpg


Mike

BroMikey
07-21-2014, 06:01 AM
► ► ► The Secret Behind The James Roney Stator ◄ ◄ ◄ - YouTube (http://www.youtube.com/watch?v=KhY7hHb2l6o)


This video is now public. For reasons unbeknown to me, most were not able to view it once I added them to the allowed list for this video. I have turned comments back on.

► One way shielding. A must see to believe. I originally posted this video on Youtube and then Youtube to sent me a letter telling me point blank from their legal department telling me that posting these videos that show cause and effect of magnets related to generating free energy, is in violation of Youtube's community guidelines. When you read their community guidelines, you quickly see that in no way, shape or form do my videos violate Youtube's community guidelines. If so, point it out to me then. Note: I'm not selling anything, or asking for anything, nor am I promoting a product for sale, nor am I endorsing anyone, which is not even covered in the community guidelines anyway. I'm not violating any community rules here whatsoever. Copy and repost my videos where ever you like while you still can, before my video are gone for a third time!! ► Can't say I did not warn you. ◄

► FYI: Google Pours Massive Investment into Renewable Energy Research. Don't believe me??? Just Google it! lol

► We must remember that Google is a publicly traded company, and Google does not want some small guy like me coming along and pulling the rug out from underneath their feet?

► Food for thought: Ask yourself this. Why is it that some free magnetic energy channels stay up that are on the up and up, while other channels like mine get taken down???

________________________________________*___
SPECIAL NOTE TO KNOWITALLS:

First... a big THANK YOU! ...to all those who have given me 'constructive" feedback and encouragement in the continued research and development of free energy via magnetism. Sadly there are those out there who feel it's their duty to lie and mislead you about my research. To set the record straight, my work has nothing to do with perpetual energy as magnets don't last forever. Nor does my work have anything to do with V-gates, Bedini motors or what have you. Rather my work is about magnetism itself and how one might build a motor that uses only magnets to run without any magnet wire of any kind.

Formally stated; Newton's third law is: For every action, there is an equal and opposite reaction; in this case, magnetic forces. My objective is simple: "To overcome the cause and effect between two opposite poles where not all of the net gain from the initial attraction is totally lost by an equal and opposite attraction."

Because of all the lies, false claims and accusations made against my simple experiments with magnets, I feel it's best that I turn off REAL TIME comments and will approve them. However I have left the negative comments and ignorant attacks on my work so as you can easily identify the culprits and flamers that caused me to turn off comments on most of my videos in the first place. You have my permission to "have at them" on my behalf via their YouTube channel.

Lastly, as a business owner, my day starts at 8:30 AM to 10:00 PM, seven days a week ever since early 2013. Thus I've no time for magnets right now. That will drastically change in early 2014 once I close my current business for good.

If you CAREFULLY replicate my work, you will discover what I have revealed in my videos 'actually works' the way it works in my videos. Rather than attack my work, do it yourself and then you will see my research and results are as real as it gets. Otherwise bug off and don't come back.


*By the way, I have nothing for sale. Never did. All the info is "OPEN SOURCE" only that I claim Copyright to my videos itself and not the information or contents contained within, thus my videos my NOT be used to make money from on YouTube or elsewhere without written permission. I do NOT have a working prototype at this time, nor have I ever had an actual working prototype.

Cheers!

James Roney Stators

BroMikey
07-21-2014, 06:18 AM
Magnet Motor concept and How magnetic shielding works - YouTube (http://www.youtube.com/watch?v=vUcWn1x3Tss)


Permanent Magnet Motor - YouTube (http://www.youtube.com/watch?v=z-vYOXm5hrM)


Free magnetic energy, magnetic shielding is the key to perpetual force and never endless rotation - YouTube (http://www.youtube.com/watch?v=qxN4I_c5Xlw)


How to make a "monopole" magnet - YouTube (http://www.youtube.com/watch?v=6iEnQw2Wt7w)


Flynn Parallel Path Device test 1 - YouTube (http://www.youtube.com/watch?v=kAO44dOC6m0)


Switching Permantent Magnet Field.wmv - YouTube (http://www.youtube.com/watch?v=Z_UHixEy7xU)

TheoriaApophasis
07-21-2014, 08:27 AM
I was ALMOST going to call a stinker on the "monopole" video until I saw it, since no such thing exists.

:rofl:

http://kathodos.com/FIELDMOVEMENT.jpg

BroMikey
07-21-2014, 08:36 PM
Isn't it crazy that all of these people making these motors work can't hear any air noise. They all think is works and for them is does. As for the rest of the people who say it will never work, that is correct for them as well.


The "AIR NOISE" is the noise of millions of buzzing voices who say "IT'LL NEVER WORK" now thats a lot of noise.:thumbsup:

As long as people don't know it won't work they keep on hoping and believing they can make a free energy machine:D

That James guy can't find time right now to work on his magnets so he gave it all away on youtube. The dead batteries inside and the shielding makes for a one way magnet. Or mono directed type whatever you call it.

IT WORKS is the main thing and while people with DEEEP understanding and POWERFUL credentials say it can't function the poor boys will make it work.:cheers:

Also I need to put up some pictures of Howard Johnsons shielding materials, he used rubber spacers and metals. Plus Howie has a ceramic tile cutter he used on magnet blocks instead of using it to cut bathroom floor tiles for around the stool:suprise:


Triangular cuts glued to rectangular shaped blocks with shields redirected the magnetic pathways til Howard had (FOR ALL PRACTICAL PURPOSES) a UNIDIRECTIONAL magnetic magnet or whatever it is called.

Whatever folks call it, the magnets pull hard on one pole and the other one don't work.

The free energy fun is just beginning and the AIR NOISE is so low now that no one can hear their voices anymore.

Thanks to men like John Bedini, Peter L. Aaron, Eric, I can't begin to name them all.

Mike

BroMikey
08-15-2014, 07:28 AM
http://members.tele2.nl/kovavla/pictures/perendev_calloway_variant_labeled_NScorrected_full .gif

https://d2t1xqejof9utc.cloudfront.net/screenshots/pics/fda1b8893d360b5e3180ba6089c377eb/medium.bmp

http://climateofsophistry.files.wordpress.com/2013/02/vortex.jpg

http://aboutfreeenergy.com/wp-content/uploads/2011/04/Magnetic-Motor-Free-Energy.jpg

http://i0.wp.com/www.greenoptimistic.com/wp-content/uploads/2008/07/new_motor_with_shields_375.jpg

http://i.ytimg.com/vi/yodY1jH5j-I/hqdefault.jpg


http://i.ytimg.com/vi/4Ge2h8Apgd8/0.jpg

http://i2.ytimg.com/vi/gQ4TlyTOsho/0.jpg

http://i.ytimg.com/vi/NxF29DzXcRo/0.jpg

TheoriaApophasis
08-15-2014, 09:49 AM
one should always support the experimenter :thumbsup:


its tough stuff!

http://www.overunity.com/14767/ultimate-proof-of-magnetic-vortex-free-book-and-videos/dlattach/attach/141727/image//

BroMikey
08-15-2014, 09:16 PM
Is this your way of saying, AFFIRMATIVE?

I guess I am bringing you guys out of the woodwork AAA? You have no idea.

Mike

BroMikey
08-16-2014, 02:13 AM
A real machine, no bread boards. Looping power endlessly. Move over skeptics.

https://www.youtube.com/watch?v=8Gl45Ulf7Us

http://peswiki.com/images/d/d4/140215_QuantaMagnetics_T2_350.jpg

BroMikey
08-16-2014, 04:15 AM
https://www.youtube.com/watch?v=G7bVeiZU5kM

BroMikey
09-06-2014, 10:56 PM
Here is Dr. Kanarev


http://192.211.49.220/-%20Free%20Energy/Kanarev/Overunity%20Motor-Generator%20by%20Professor%20Ph.%20M.%20Kanarev.fl v

BroMikey
09-24-2014, 03:23 AM
Saw this on overunity.com and I have a feeling this fellow might be on the right track.

YouTube - Magnet Motor Prototype (http://www.youtube.com/watch?v=jZjEYu9BbW0)




The problem I have seen with all permanent magnet motors so far is that everyone keeps thinking in two dimensions which is a big shortcoming.

This fellow has expanded into the third dimension and you can already see improvement over those two dimensional spiral motors.

I would take this a few steps further (or turn it up couple of notches :) ). Instead of a cylinder use an inverted cone (apex down) so that we have a vortex/spiral, and pieces on the cone are constantly spiraling or "falling" down into the vortex. I remember reading about David Hamel and his revelations where he said that his device is all about being out of alignment and constantly "falling" so that clicked in right away after seeing this.


Amigo

Here is another great motor he claims the battery keeps rising which is more than most posted inventions have ever done. Most drain the battery.

Microwave Transformer Magnet Motor - YouTube (http://www.youtube.com/watch?v=T5RtBVvOviA)

Magnetic generator Motor using Microwave Oven parts - YouTube (http://www.youtube.com/watch?v=pUDnPQY6yJI)



http://i.ytimg.com/vi/T5RtBVvOviA/maxresdefault.jpg

BroMikey
09-25-2014, 01:35 AM
Here is the secret of a magnetically run engine like the MONOPOLE should be built. It should use Howard Johnsons ideas of shaping a magnetic field so the Monopole Motor can run in an O.U. state.

Move over world new technology is coming through.

I know you may not understand what this is at first but I will keep posting on Howards stuff.

http://www.resonantfractals.org/Magnetism/Neutron_Spin_Coherence_files/CoherentControl.jpg


http://freeenergynews.com/Directory/Howard_Johnson_Motor/Blueprints/images/p2of4/HJ2top2_600.gif



http://1.bp.blogspot.com/-UafYquKYc_o/Ts4sxXK2dKI/AAAAAAAACCs/0SIMAqiNPU4/s1600/01.gif


http://freeenergynews.com/Directory/Howard_Johnson_Motor/1979Paper/images/fig01.gif

http://www.callowayengines.com/msg24.gif






Mike

BroMikey
09-25-2014, 08:36 AM
Youtube Motor no magnets


https://www.youtube.com/watch?v=VkBGfcZjXvM


http://www.jrmagnetics.com/magapps/fluxgate/fluxgatedesign_1.png

TheoriaApophasis
09-25-2014, 09:15 AM
Youtube Motor no magnets


https://www.youtube.com/watch?v=VkBGfcZjXvM


http://www.jrmagnetics.com/magapps/fluxgate/fluxgatedesign_1.png



that video is a lie, is pure nonsense



also, monopoles dont exist :rolleyes: :rolleyes:

BroMikey
09-25-2014, 09:55 AM
Many things are not what they appear to be. One must always read between the lines of motivations.:thumbsup: Stay tuned for free energy!!:thumbsup: Just kidding. I mean getting tapped into the lightening bolt size power from the ionoshere whatcamacallit.

Most people call it that but we know better HUH?;) So ya gotta work with whats out here.

Mikey

garrypm
09-25-2014, 09:12 PM
Amigo

Here is another great motor he claims the battery keeps rising which is more than most posted inventions have ever done. Most drain the battery.

Microwave Transformer Magnet Motor - YouTube (http://www.youtube.com/watch?v=T5RtBVvOviA)

Magnetic generator Motor using Microwave Oven parts - YouTube (http://www.youtube.com/watch?v=pUDnPQY6yJI)



http://i.ytimg.com/vi/T5RtBVvOviA/maxresdefault.jpg


Hi Mikey,
Did you take the time to watch his overunity flywheel -

Flywheel Energy Overunity - YouTube (http://www.youtube.com/watch?v=xvhwEDeEp18&index=2&list=UUPG9tPsA51_Daae-Qm1MJ0g)

Would like to know the motor type that he claims is from a VCR.

Cheers, Garry

BroMikey
09-29-2014, 06:00 AM
Hi Mikey,
Did you take the time to watch his overunity flywheel -

Flywheel Energy Overunity - YouTube (http://www.youtube.com/watch?v=xvhwEDeEp18&index=2&list=UUPG9tPsA51_Daae-Qm1MJ0g)

Would like to know the motor type that he claims is from a VCR.

Cheers, Garry

Hi Gary

Not really sure of all of his details but it reminded me of the Newman motor coil that most people thought was a hoax for the last 50 years.

The bedini window motor windings are not exactly the same but close.

I think with his broken English he is hard to understand but maybe he got the bearing out of a VCR for free letting people know where to get good ones.

He says the coil is out of a microwave oven transformer.


I post this stuff because almost no one has any practical O.U and this guy makes it childs play.

Pretty insulting hey? Well I cried "UNCLE" quite awhile back finding O.U. and now it seems to fall into my lap.

I was making it out to be hard. Just get some magnets and coils, that is too easy.

I watched it again and the tiny motor is out of a VCR for opening the drawer.

The big one is a gear reduced stepper motor out of a paint machine he says.

Mikey

BroMikey
11-04-2014, 07:08 AM
Here is a self runner

https://www.youtube.com/watch?v=jKFTAobM-l0

http://img69.imageshack.us/img69/9695/amms.jpg


Mike

Dog-One
11-04-2014, 07:58 AM
[SIZE="4"]Here is a self runner

https://www.youtube.com/watch?v=jKFTAobM-l0

Mike

Easy does it Mikey. I'm pretty sure where I saw this one dissembled with batteries inside the coils. Those bolts don't go all the way through.

In fact he even says:
Don`t waste your time with a replication of these motor / generator.

Now you can make a replication of my motor / generator for fun and it will run. It has now run 35 hours on 2 pcs. 800 mah NiMH accu batteries and then stopped.


Amazing Magnetmotor Motor/gen Diagram Part 3. - YouTube (http://www.youtube.com/watch?v=fM6-4D74bi4)

BroMikey
11-04-2014, 08:12 AM
You Dog you. Popping my bubble Hey?:thumbsup:

You know everybody personally. Been around awhile hey?:D

Not me, I am one of those guys who trusts people, well til they are found out to be liars.

Thanks again Dog. I will BRB



Easy does it Mikey. I'm pretty sure where I saw this one dissembled with batteries inside the coils. Those bolts don't go all the way through.

In fact he even says:


Amazing Magnetmotor Motor/gen Diagram Part 3. - YouTube (http://www.youtube.com/watch?v=fM6-4D74bi4)

BroMikey
11-06-2014, 01:20 AM
Extra fun with free energy motor.


https://www.youtube.com/watch?v=2qJP4rGfv7o


http://teslafreeenergy.files.wordpress.com/2011/03/motor_gemini_cutaway-300x284.jpg

BroMikey
12-22-2014, 07:05 AM
Free energy all around

Over 3000 watts 24/7:thumbsup:



https://www.youtube.com/watch?v=C0IbppxPdHc


http://peswiki.com/images/2/21/Wasif-Kahloon_magnet-motor_open_sunlight_400.jpg

BroMikey
01-02-2015, 08:19 AM
Magnet motor non linear magnetic forces. Pole reversal at TDC.:D Key phrases take the cake. Free energy comin up.:thumbsup:


https://www.youtube.com/watch?v=c2qjF8x-HA8


http://i.ytimg.com/vi/c2qjF8x-HA8/mqdefault.jpg

Dog-One
01-02-2015, 08:44 AM
Magnet motor non linear magnetic forces. Pole reversal at TDC.:D Key phrases take the cake. Free energy comin up.:thumbsup:

http://i.ytimg.com/vi/c2qjF8x-HA8/mqdefault.jpg

Not sure I believe that specific rendition, only because I spent days trying to do the same thing, but I will say, I know a PhD that personally saw the Yildiz magnet motor run and he is convinced it's possible. He's still working out the mathematics to prove it.


Ken understands this stuff probably better than anyone. I'm guessing it won't be long until he slaps something together to prove one of his theories and bingo, you'll have a video. It's only a matter of time. Dielectric inertia baby. You get that whipped and you'll be all set.

BroMikey
01-02-2015, 09:17 AM
Not sure I believe that specific rendition, only because I spent days trying to do the same thing, but I will say, I know a PhD that personally saw the Yildiz magnet motor run and he is convinced it's possible. He's still working out the mathematics to prove it.


Ken understands this stuff probably better than anyone. I'm guessing it won't be long until he slaps something together to prove one of his theories and bingo, you'll have a video. It's only a matter of time. Dielectric inertia baby. You get that whipped and you'll be all set.


Hey Dog

Good to know the path is well beaten. Thanks-A-Million:D Maybe it will be worth a shot.:thumbsup:

Now here is a mechanically switched magnet pole. John Bedini says we can do the same thing with a stack of various magnets without them rotating.

Two words, Howard Johnson. Non linear magnets that can reverse poles at the trigger point. That is the way John Bedini's BIG MACHINE works.

I am sure you know what I am going to say but for the sake of others, I will repeat it again. The moving magnet is pulled in to the stationary magnet and when it reached the fully locked position the pole reverses pushing the rotating magnet away. BINGO!!! Free energy!!

John Bedini showed his 16 pole (Looks like a red ribbon) Ferris Wheel in PART 22. This machine puts out gigantic amounts of power due the the magnet stacks made to reserve polarity.

A solar panel is quicker but only works when the sun is out;)

Remember Howy stacked magnets using neo, ceramic, rubber, steel and aluminum shielding, triangular cuts. This video shows the mechanical version.

https://www.youtube.com/watch?v=vBRDvwrFwVo


http://i.ytimg.com/vi/z8--9z9WTRM/hqdefault.jpg

http://i.ytimg.com/vi/hoiReuIlqMI/hqdefault.jpg

BroMikey
01-02-2015, 09:27 AM
This one works but does not push, it only pulls. Half as good but it works.



Self Runner:thumbsup:

https://www.youtube.com/watch?v=QLufUUpqNgU





http://img.youtube.com/vi/QLufUUpqNgU/0.jpg

Stealth
01-02-2015, 07:44 PM
Nice video. I have, over the years built many magnetic motor configurations. Some were very close to being self running. The greatest obstacle to overcome in a self running magnetic motor is size. In simple terms, you need a wheel large enough to have sufficient distance between each magnet or magnetic section. It needs to assume a neutral position after it has engaged the stator section before engaging another magnet on the rotor. Here a some examples of working magnetic motors. Some more are the Bowman motor, Hampster Cage motor. Good Luck. stealth

BroMikey
01-02-2015, 09:19 PM
Nice video. I have, over the years built many magnetic motor configurations. Some were very close to being self running. The greatest obstacle to overcome in a self running magnetic motor is size. In simple terms, you need a wheel large enough to have sufficient distance between each magnet or magnetic section. It needs to assume a neutral position after it has engaged the stator section before engaging another magnet on the rotor. Here a some examples of working magnetic motors. Some more are the Bowman motor, Hampster Cage motor. Good Luck. stealth


Hi Stealth

Talk to me about Bowman, Hampster cage? Magnet motors? You have these?

I understand what you said about spaces. I never built one.

What did you think about the self runner using a scooter motor to generate?

The one I am thinking about uses simple ring magnets spaced out nicely and a single ring magnet over head rotates?

I have scene a half dozen of these fully operational all from people who do not know one another.

The mechanical pole switching can be replaced with stationary pole flipping using Howard Johnson's magnetic gate shaping experiments.

Mikey:thumbsup:

BroMikey
01-02-2015, 09:35 PM
Here is a magnetic Vortex motor conversion experiment. The picture shows us what John Bedini showed us years and years ago how magnets offer free energy. The Video is the same thing? I think?:thumbsup: :D Amigo your motor is in:D

https://www.youtube.com/watch?v=2qJP4rGfv7o



http://thegreaterpicture.com/images/magnetic_motor.jpg

BroMikey
01-02-2015, 09:49 PM
Ladies and gentlemen boys and girls, I give you a serious replicator of Howard Johnson's work. All of Howy's hidden magnets. Got to protect the patent, you know.

Free energy is all around. This is a great adventure. John Bedini did it, so can we.:thumbsup:



https://www.youtube.com/watch?v=zavp87bKgnQ

http://i.ytimg.com/vi/OZ-mGJaipT0/hqdefault.jpg

Stealth
01-03-2015, 01:16 AM
The ring magnet(s) is a gate magnet. It works exactly like a row of magnets in a linear configuration in that it pulls in one directions and pushes in the opposite. Once you can overcome the initial repulsion of the like poles, then it will repel through with great force and speed. If you are going to use that configuration, you will have to split the case and make a section for a wheel to travel through. This configuration has a strong magnetic pull and repulsion because of the combined strength of the magnets. The Bowman motor is three wheels, 1 is large and the other 2 are 1/2 size and they are all geared together. As the large on turns, the two smaller one rotate in the opposite direction. All north faces on the large one and like on one small one, and opposite on the other. This sets up a push-pull relationship with the large wheel. An offset magnet then keeps the wheels unbalanced to keep it in motion. More later. Good Luck. stealth

BroMikey
01-03-2015, 01:55 AM
The ring magnet(s) is a gate magnet. It works exactly like a row of magnets in a linear configuration in that it pulls in one directions and pushes in the opposite. Once you can overcome the initial repulsion of the like poles, then it will repel through with great force and speed. If you are going to use that configuration, you will have to split the case and make a section for a wheel to travel through. This configuration has a strong magnetic pull and repulsion because of the combined strength of the magnets. The Bowman motor is three wheels, 1 is large and the other 2 are 1/2 size and they are all geared together. As the large on turns, the two smaller one rotate in the opposite direction. All north faces on the large one and like on one small one, and opposite on the other. This sets up a push-pull relationship with the large wheel. An offset magnet then keeps the wheels unbalanced to keep it in motion. More later. Good Luck. stealth


Sounds good. I got alot of catching up to do I see.

For all the Amigo's here is a V-Gate with mechanical reset.

Many possibilities exist. This is a test for a possible functioning OVER UNITY DEVICE.

Move over world.:D I want thank everyone for sharing in the other thread.:thumbsup: Sharing makes you a winner.

https://www.youtube.com/watch?v=gtm4BwfIvUs
(https://www.youtube.com/watch?v=gtm4BwfIvUs)

https://www.youtube.com/watch?v=JL6iAf0WEmA




http://s017.radikal.ru/i420/1111/f1/69a3a8ca655b.jpg

BroMikey
01-03-2015, 05:53 AM
This V-Gate has a double acting mechanical pole reversing switching.

Still incomplete. I find very few V-Gate motors that are complete.

This one looks better than all I have found so far. This one needs a timing belt.:thinking:

https://www.youtube.com/watch?v=A7Zepnqrux4


http://i.ytimg.com/vi/hbj3rIFVb5w/hqdefault.jpg

BroMikey
01-03-2015, 06:50 AM
In these videos we find some good points to retain. From close observation of the picture we can see that many combinations are possible. Many designs work just as good as the next. Not all.:thumbsup:



HOWARD JOHNSON Linear Magnetic Motor

https://www.youtube.com/watch?v=618k46W3kNY



https://www.youtube.com/watch?v=-u3fOwkiM7U



http://www.cheniere.org/images/Johnson/johnso1.gif



http://img.youtube.com/vi/618k46W3kNY/0.jpg



http://cheniere.org/images/people/Howard%20Johnson/Howard%20Johnson%20with%20gate.jpg



http://energyfromthevacuum.com/Disc4HoJo/PICT3837a.jpg



http://www.energyfromthevacuum.com/images/Image4001a.jpg



https://i.ytimg.com/vi/JJfYd1jJ6N0/hqdefault.jpg



http://i.ytimg.com/vi/OZ-mGJaipT0/hqdefault.jpg



Have fun anyone can do it.:thumbsup:


http://chemicalengineeringnews.org/wp-content/uploads/2013/07/funny-cat-picture-with-caption.jpg

BroMikey
01-03-2015, 07:05 AM
Mylow experimenting and making progress.:thumbsup:

https://www.youtube.com/watch?v=NSyMPrVUDm4



https://www.youtube.com/watch?v=Z9bYfc3xLq8



http://i.ytimg.com/vi/NSyMPrVUDm4/hqdefault.jpg

BroMikey
01-03-2015, 08:18 AM
Jeremiah Sturk use Pyrolytic Graphite to shield his magnets


https://www.youtube.com/watch?v=6Lz09rqmP-0


Pyrolytic Graphite Sheets – Panasonic | DigiKey (http://www.digikey.com/us/en/ph/panasonic/pgs.html)


Directory:Jeremiah Sturk's Magnet Motor - PESWiki (http://peswiki.com/index.php/Directory:Jeremiah_Sturk%27s_Magnet_Motor)



http://i.ytimg.com/vi/6Lz09rqmP-0/hqdefault.jpg

Turion
01-04-2015, 05:50 AM
I basically told him I could put him in front of some investors if he had a working prototype. This was his response.

I do have a small example of a device producing energy, it is like a battery
and a very simple demonstration. The full prototype that will produce 6KW @ 6Amps with regenerative capabilities requires several different metallic powders with a -Negative ion hemisphere ties to a +Positive ion hemisphere connected in series will produce clean, safe and lightning like energy. However this will require a 120 ton powder press and a magnetizer to produce. The materials needed are very expensive and I would need at least $1.5 Mil. I am willing to offer a percentage to an investor, but before I will do anything I need help on a different project.

You see I own 40 acres in Montana and I need about $150,000 to finish developing
The land. I want to help about 3-4 families have a place to live and also where we can
grow Organic, Non-GMO food. This property will remain off grid and would be a great
place to build a magnetic energy device! Here are a few links to this first project.
Here is my Intentional Communities Page:
Freedom Farm - Fellowship for Intentional Community (http://www.ic.org/directory/thefuturenow/)
Freedom Farm Link:
freedomfarms (http://trimetatron.wix.com/freedomfarms)

BroMikey
01-05-2015, 07:45 AM
Free energy motor using a magnet making light.

https://www.youtube.com/watch?v=tcfD6V7pQqc


http://img.youtube.com/vi/tcfD6V7pQqc/0.jpg

BroMikey
01-05-2015, 07:51 AM
Free energy lighting simple and easy using only a coil and magnets plus a small cap. Enjoy :thumbsup:

https://www.youtube.com/watch?v=89duz7xAifI


http://i.ytimg.com/vi/89duz7xAifI/hqdefault.jpg

BroMikey
01-05-2015, 07:56 AM
No battery no nothing just coils and a transistor. Motoring free.:thumbsup:



https://www.youtube.com/watch?v=vOgp7Z8dOtw



https://i.ytimg.com/vi/vOgp7Z8dOtw/0.jpg

BroMikey
01-06-2015, 05:51 AM
Magnet Motor/Generator.



https://www.youtube.com/watch?v=N1l3Fzp1rLw



http://i.ytimg.com/vi/AZOwiiR3oWQ/hqdefault.jpg

BroMikey
01-06-2015, 06:44 AM
I have searched 1000 times and 1000 times again and I always find new ones.


Top 3 energy from magnets? Donno?

https://www.youtube.com/watch?v=FgL4gWPY21U



http://img.youtube.com/vi/FgL4gWPY21U/0.jpg

BroMikey
01-06-2015, 07:02 AM
Magnet motor schooling for us side line pigeons :D


https://www.youtube.com/watch?v=etFCzIe-D2Y


http://img.youtube.com/vi/etFCzIe-D2Y/0.jpg

BroMikey
01-15-2015, 03:46 AM
Here we have a free energy magnetic engine driven electric truck


https://www.youtube.com/watch?v=7jR4DvNO0jg#t=206


http://i2.ytimg.com/vi/7jR4DvNO0jg/0.jpg

BroMikey
01-30-2015, 02:47 AM
Here is the secret of a "Self Running Monople Magnetic Motor" courtesy of John Bedini's Howard Johnson video's "ENERGY FROM THE VACUUM"

I am not kidding either, this is the answer some of you have been looking for over the long long years.

Watch as the young man replicates.

With what you see from these replicators you and I can build a home generating system.

The magnets are cut and stacked, set on proper angles. Neo ,ceramic, rubber magnet arrays. One set of arced magnets.

In part 22 John Bedini is asked by the audience why his Ferris Where with 16 poles had convex (Curved inwardly) surfaces.

Here is part of your answer. Start spreading the word to your friends who have large multipole units only getting spikes:thumbsup:

The secret is out of the bag.:thumbsup:


https://www.youtube.com/watch?v=Kqsa2ZptudM

http://i.ytimg.com/vi/OZ-mGJaipT0/hqdefault.jpg

Turion
01-30-2015, 04:43 AM
There is a magnetic gate at the beginning of this track that the car must be "FORCED" through before the magnets take hold and send it on its way. What is the amount of force required (over what length of time....the definition of WORK) to do this vs the work that is achieved at the exit of the gate at the other end? Perhaps before we claim this is the "answer we have all been looking for" we should do a little research and have an answer to that simple question. Hmmmm?

BroMikey
01-30-2015, 08:07 AM
There is a magnetic gate at the beginning of this track that the car must be "FORCED" through before the magnets take hold and send it on its way. What is the amount of force required (over what length of time....the definition of WORK) to do this vs the work that is achieved at the exit of the gate at the other end? Perhaps before we claim this is the "answer we have all been looking for" we should do a little research and have an answer to that simple question. Hmmmm?

Hey Turion

Yeah that sounds like a winner. Maybe it would be a good idea to let people know that this is the correct direction to go in. No one who is on the inside is permitted to proclaim what John Bedini has shown us in PART22.

I agree, we don't know everything about John Bedini's Ferris wheel improvement. We don't know the exact amounts of force and so forth.

We don't hear about anyone who has done what John Bedini has shown either.

However what we do know is this.

(1) Huge amounts of power pour off of John Bedini's Ferris wheel

(2) John HIMSELF stated that "It would run like that forever"

(3) That the people with Monopole's don't have this with the SSG

(4) John stated Howard Johnson's magnetic gates were the key.

(5) John's Ferris Wheel poles uses specially cut convex (curved in wardly) magnets.

Don't take my word for it Buy Part 22 and listen to John blowing in the wind I guess.;)

As far as me telling everyone everything there is to know INSIDE the mind of John Bedini, I can't:) You are the one to help me out?

Also if you look around at the Howard Gates replications you will see more clues. Not all setups were the same with Howard's work, he reminded me of how many variations I have seen of John's work.

These guys are baffling to follow with their endless possible combinations of how it might be made to achieve the same goal.

So yes you are right Turion, I have not made these gates work completely yet and I can't lead the group step by step to build John's Ferris wheel, all by myself.

But let me ask all of the people something.

Do you think John Bedini gave away the clues in 2010 just for kicks, or do you think John was not telling us right? Do you think John Bedini wants us to find the answers?

The man in the video is way ahead because he is following John's lead by building these gates.

John himself gave us the answer and no one can show a set of magnetic gates that flip poles and self run. Other magnet motors around the world self run but I am not looking at those.

I am looking at a Ferris wheel with 16 convex magnetic gates swinging around from floor to ceiling that pass 2 huge coils with no doubt the other half of the gates inside them.

I didn't say I had all the answers, but no one is putting 2 and 2 together anywhere on the web. What I am saying is I believe John Bedini WANTED us to find the answers from the clues he had already given up to that point in 2010 when John shamed the old leaders of the Monopole group from years ago.

I know the answer is there and that it isn't all that hard either.

John Bedini wants us to follow his lead and I don't see anyone giving it the time of day. Do you really think we are along on this forum?

If people knew what direction to go in, they would have a start. They don't.

The people are in confusion, they don't know that what I am saying is correct.

How many decades more should we wait?

I understand your point Turion, you don't want to say something works unless you have it working and I can respect that.

I am talking about the direction to go in for the young guys.

One of the biggest things that really qissed me off about Sterling years ago when he started, was the way he brought up John Bedini's bike wheel, showed it in 2 minutes, said it didn't work and quickly went to another gadget. I never watched him again, I always turned him off.

Are we any different?

We have the answer right under our noses, been told that the monopole has the answers and we are not sure what to do.:rofl:

THAT is what I am saying. I am saying that this is the way to go. That is all.

Not that I have all of the intricate details.

We work on all these Bi-toroids and double coil this and a two coil that thinking that these coils are somehow different or better than the multi-pole SSG?

The way it looks to me is that John was phasing with the monopole like a BiTT does where reactive power sets things in motion and the multiple coils act similarly to some of these other projects were putter with all day.:thinking:


I think the answer is staring us right in the face.

Your statement says that the gates have no Overunity potential and I just refuse to believe that.

Thank Turion for hearing me rant.

I will get to the bottom of all of this, trust me on that.

I am of the opinion that there is no better direction to go in than John Bedini's work is leading me.

I will have have a working set of gates.

Mikey:thumbsup:How-bout you?:thumbsup:

Turion
01-30-2015, 08:39 AM
Didn't say magnetic tracks had "no over-unity potential." All I said was we don't know if the input is greater than the output. And if it is, by HOW MUCH. I have built lots of these magnetic tracks. I built one with a four foot wheel as a rotor and a magnetic track as a stator that would have self run if I had the money for all the magnets required. But I didn't spend the money because I could see that the issue was the amount of POWER it put out. It could barely keep itself turning, so could do LITTLE if ANY work. The minute you added drag to it by trying to run magnets past coils, it would come to a halt. Like I have said before...getting COP>1 is easy, but it is NOT ENOUGH.

I believe what you had going on in the center of John's big wheel had more to do with the Radus Boots than with Howard Johnson's stuff. That's my guess anyway. When you can turn a magnet off and on like that, you have the potential to really produce some power....and far MORE power than the tiny bit you are going to get from the magnetic tracks. Just my thoughts, and I think the pursuit of the Radus boots technology is a far more worthwhile goal than the pursuit of magnetic tracks.

But each to his own. I have my own projects to completely test, and then I'll have some things to share. Or at least I hope I will. Test results have been good so far.

As to "huge amounts of power pouring off John's Ferris Wheel." Where do you get that from? Where do we see that? John's wheel produced power, but how much is "huge amounts" and where is the data to back that up? I was there. I saw it working. It was an awesome machine, but just how much power are you trying to tell us that machine produced? Facts man, facts!!

We are NEVER going to get where we need to be by trying to hype everybody up. We need to start with facts and data not beliefs and wishes. John's three books on the SSG are a great start. IF you understand that machine, and you understand switching, you are most of the way there. When you add running loads off the potential difference, you've reached the top of the mountain.

The Benitez patents (Tesla switch) work.
Running loads off potential differences works.
Coal collapse to generate energy works....the bigger the coil, the MORE energy you get.
We know LOTS of things that works and we just need to put them together.

When you can run a motor for FREE, what you get out of your generator is all COP>1

BroMikey
01-30-2015, 08:44 AM
There is a magnetic gate at the beginning of this track that the car must be "FORCED" through before the magnets take hold and send it on its way.


@Turion

Look at the video. Howard is not pushing 14 pounds to get the car into the gates field here. The other video yes, but not this one.

Watch as Howard just lets it go and zero opposition til the car gets close and then the pull is 14 pounds.

Good point, that is a huge difference from other video's.:)

Nobody else other than John has even come close to this. I can't believe it:yahoo:


https://www.youtube.com/watch?v=ndRrCZiM1CU


http://i.ytimg.com/vi/ndRrCZiM1CU/hqdefault.jpg

Stealth
01-30-2015, 08:04 PM
Turion is right. There are some things that need to be considered in this configuration. I have built and experimented with many such tracks in the TOMI configuration. If you run the cart (magnets) in this configuration you have a considerable amount of force to overcome before you can enter this gate. I have found that if I run it in the opposite configuration ( turn the magnetic cart around), that it will not only pull into the gate, but I can configure it to not pull back after it gets to the end of the track. In this way it is truly self running. No need to push it past the gates entrance. It will exit more slowly but the speed and power at which it runs has enough inertia to overcome most of the stick point, as most call it. By having the stator using less magnetic force (smaller magnets), on the end, it will lessen the magnetic pull back on the cart, etc. I don't use a cart, but a roll of magnets inside a 3/4'' pvc pipe . They roll down the track (runway), plywood with two sides preventing the roll form exiting over the sides. The roll must be about 1/2'' to 3/4'' smaller than the width of the track. Good Luck. stealth

BroMikey
01-30-2015, 09:04 PM
Turion is right. There are some things that need to be considered in this configuration. I have built and experimented with many such tracks............................................ .................................................. ........................................ but I can configure it to not pull back after it gets to the end of the track. In this way it is truly self running. No need to push it past the gates entrance. It will exit more slowly but the speed and power at which it runs has enough inertia to overcome most of the stick point, as most call it.

Good Luck.


stealth


Hey Stealth

GOOD LUCK? Wait-A-Minute. What is your hurry? Who needs LUCK, we have you don't we?:D

I just knew someone had a set of working gates. What would a guy have to buy to do some proper testing? I have no rubber magnets unless you call the refrigerator door stripe magnets "RUBBER MAGNETS";)


All I want is a self running motor:rofl: Please :D Just kidding Stealth, I know this will take some effort.

If we could only have an experienced person give us a few pointers. I know many clues are peppered all over the world but they are hard to find:embarrassed:

Then when you find them you don't know if they turned out to be dead ends.


Thanks Stealth, you have restored my hope for mankind:)

Mikey:thumbsup:

Stealth
01-31-2015, 12:13 AM
I will try to help you with your magnetic gates. Through many hours of experimentation I have figured out what works and what doesn't. A magnet motor is the same as an electric motor, in that everything works at right angles. By studying the TOMI, you will clearly see that a linear magnetic motor has all magnets on one side facing north, while all magnets on the far side faces south. The corresponding rotor also has a N-S on each side. The rotor must be magnetized on the ends. As the rotor rolls or moves through the track where the stator magnets are arranged, they use a push/pull, on/off, same as an electric motor. At the end of the cycle you must reduce this magnetic push/pull so that the inertia will help move the rotor past the sticky point. This can be accomplished in one of two ways, use smaller magnets on the end, or move the magnets farther away from the rotor. I call mine the butterfly effect. With both ends curved out away from the rotor. This basically eliminates the effects of the magnetic gate. Also you can add a small piece of iron past the stator magnets to help reduce the magnetic effect on the rotor as it leaves the stator. As the last magnet is pulling back on the rotor, the iron is pulling in the opposite direction on the rotor and with expermentation, you can virtually negate any pull from the stator. I mostly use the rectangular ceramic magnets from Radio Shack for testing, although you will also need some round magnets if you want to build a rolling rotor. Good Luck. stealth

BroMikey
01-31-2015, 01:06 AM
I will try to help you with your magnetic gates. Through many hours of experimentation I have figured out what works and what doesn't. A magnet motor is the same as an electric motor, in that everything works at right angles. By studying the TOMI, you will clearly see that a linear magnetic motor has all magnets on one side facing north, while all magnets on the far side faces south. The corresponding rotor also has a N-S on each side. The rotor must be magnetized on the ends. As the rotor rolls or moves through the track where the stator magnets are arranged, they use a push/pull, on/off, same as an electric motor. At the end of the cycle you must reduce this magnetic push/pull so that the inertia will help move the rotor past the sticky point. This can be accomplished in one of two ways, use smaller magnets on the end, or move the magnets farther away from the rotor. I call mine the butterfly effect. With both ends curved out away from the rotor. This basically eliminates the effects of the magnetic gate. Also you can add a small piece of iron past the stator magnets to help reduce the magnetic effect on the rotor as it leaves the stator. As the last magnet is pulling back on the rotor, the iron is pulling in the opposite direction on the rotor and with expermentation, you can virtually negate any pull from the stator. I mostly use the rectangular ceramic magnets from Radio Shack for testing, although you will also need some round magnets if you want to build a rolling rotor. Good Luck. stealth


"Theory"--"Of"--"Magnetic"--"Instability":) Thus "TOMI" Gotcha

TOMI Build it (http://www.keelynet.com/energy/tomibild.htm)


Now I know what's what, who has it goin on and who is dead in the water.

So study the TOMI :thinking: Humm...

http://www.keelynet.com/energy/pbp.jpg


Is this a TOMI track? Or how does this diagram play into Howards work? I think some stuff on the web is a dead end.

http://www.westerndigitalproductions.net/hj2.jpg


I have played with magnets but don't know all of the terms.

I have one of those pancake washer motors with the magnet rotor? I am wondering about you essay on orientation of your setup.

Further way on both ends:thinking:or a chuck of metal to pull fields over:thinking:or magnets on the end out farther?:thinking: You got me thinking.

Right angles for motors:thinking:Humm......Right angles from rotor to stator?

Do you have a basic diagram of that jewel? I got to see it to roll it around.

I mean I see a lot all over the world wide web but I am like a wandering blind man when it comes to pin pointing a visualization of your specific brain storm.

I don't doubt you can see it in your minds eye.

Thanks for the start Stealth, I am looking at TOMI stuff right now.

TOMI humm... :thinking: To all good things there is a start.

What is your youtube handle so I can see it running:thumbsup::D

Mikey:thumbsup:

Stealth
01-31-2015, 08:35 PM
Sorry, but I don't post videos on you tube. Many of the videos on there are fake anyway. It is easy to make a video and dub it so to make it look real. I have built some of the motors that came off you tube and they didn't work, followed them to the letter, too. The two stator magnet sections have their poles straight up, one North and one south. The rotor poles are side to side towards the magnetic stator sections, therefore at a right angle, same as an electric motor. Put a steel plat under the stator magnets to concentrate their power. Put a divider (wood/metal), one third the thickness of each stator section between them. Here is what I consider to be the easiest magnet motor to build to date, works too. It will give you more insight into how magnets interact with each other. This is the Bedini magnet motor. Good Luck. stealth

BroMikey
02-01-2015, 12:45 AM
Sorry, but I don't post videos on you tube. Many of the videos on there are fake anyway. It is easy to make a video and dub it so to make it look real. I have built some of the motors that came off you tube and they didn't work, followed them to the letter, too. The two stator magnet sections have their poles straight up, one North and one south. The rotor poles are side to side towards the magnetic stator sections, therefore at a right angle, same as an electric motor. Put a steel plat under the stator magnets to concentrate their power. Put a divider (wood/metal), one third the thickness of each stator section between them. Here is what I consider to be the easiest magnet motor to build to date, works too. It will give you more insight into how magnets interact with each other. This is the Bedini magnet motor. Good Luck. stealth

Wow. I never saw this at the ICEHOUSE. Is it really a John Bedini diagram? Or are you giving John some credit here?

This is too Kool. You mean all these decades have past and no one is showing this on YOUTUBE? I believe you are right Stealth with the disinformation groups sent out to confuse folks.

I am with you on the stuff posted in video form. And when some do post a working (At their house) they either can't speak English or can not teach.

Okay looking at this motor I have seen this picture on the web for years.

Not your drawing, I mean this drawing.

But when compared to your diagram we see that things are missing.

In your diagram it looks like to me that the handle object is a sort of counter balancing weight to promote the oscillation as magnets pass by.

http://thesilentroom.com/fyp/wp-content/uploads/2013/08/wheel.png

Also the handle/balancing weight, I assume made of metal, performs a shielding task that allows the rotor magnet to approach it without repulsion.

Your diagram is more precise.

http://flyer.thenetteam.net/jbmagneticmotor.jpg

BRB everyone, we really need to give honor where honor is due. Thanks Stealth. I will be right back to rake this over the coals. This is what we have all been waiting for.:thumbsup:

Mikey:D


Okay I am back Stealth

This is so simple:thinking:wait or is it?:thinking:

The handle looking thing is a shield, now I got it. It doesn't move. Okay now.


Put a divider (wood/metal), one third the thickness of each stator section between them.
Good Luck. stealth

Hum....... I got to have more time:thinking: 1/3 thickness wood/metal:thinking:

It looks like this forum is stuck Stealth. Everyone is saving this drawing. Thank you very much Stealth.

Also before I go look at this more I wanted to make sure it was alright to send this to all of my friends. I have this in a special place.

Mikey:thumbsup:PS you are the man of the hour

wayne.ct
02-01-2015, 01:01 AM
I think by now you've figured this out, Mike, but I want to add a bit of explanation for anyone else that may be still in the dark. Imagine some children sledding on the snow on the side of a hill. The sled wants to slide down the hill and just a "little" push at the top of the hill gets you started. From that point you could "go" forever if only you could cut down on the friction. The problem is that you continue adjusting the grade of the slope and waxing the runners, but there remains that pesky problem of getting back to the top of the slope to start again. The "ski lift" is the "gate" or "sticky spot" and you've got to put some energy in to get back to the top of the hill. The only escape from that may be the "twist" in the magnetic flux, but I have yet to see an actual build that gives me enough confidence to drop my "other" projects and try to construct a replication. If you go back far enough in this forum you will see that I tried to build a magnet motor. I was very excited about it at the time. But in the end I did not have good results so I stopped talking about it. With money and better construction technique, I might make a new attempt. But for now, I think I have a better idea and so I am concentrating on that.

BroMikey
02-01-2015, 02:19 AM
I think by now you've figured this out, Mike, but I want to add a bit of explanation .................................................. ..............................

The only escape from that may be the "twist" in the magnetic flux


If you go back far enough in this forum you will see that I tried to build a magnet motor............................................. ............................

I did not have good results



Hi Wayne

I think many of us with a half hearted attempt has fudged a magnet motor or two:D it is time now to shift gears to positive results, let's focus on that.

Now if you felt that SOME of the data you had collected through testing was worth salvaging, by all means dig it up. I wouldn't have a clue where that data is.

It would be welcome I am sure. Many men having working units similar to what Stealth has shown but there always seems to be a missing part.

Maybe now we can all move out of our down cast junk room into high gear:D

Many young men would hoover a project such as this till they succeed. Let's not deny them this opportunity to be physically consumed by a worth wile device.

Run Rabbits run.:D

Mikey:thumbsup:

Turion
02-01-2015, 03:04 AM
The problem with this design is that there is nothing that says the roll of magnets will be pushed Up the hill rather than DOWN the hill from the first interaction between like magnets that repel.

Stealth
02-01-2015, 03:51 AM
The four reference names say it all. It was designed with the help of Bearden, Johnson and Cole. Bedini built the motor and did the testing, as well as I remember. The arm is iron or steel which attracts the magnets, then at the point where it travels past the steel arm, the magnet behind the arm repels the magnetic rotor. The steel arm is fashioned in a way so that as the magnetic rotor approaches it, It comes closer and closer to the arm, therefore it moves along in the attraction mode until it enters the point where the magnet repels it. It doesn't show it, but I would guess that a device is in place to prevent the rotor from turning backwards. Also you could add more arms and magnets to make it a stronger motor. The only limit is size and space. I don't know the date at which it was released, but I am speculating in the 1980's. I think John made a reference as to its working continuously somewhere. Anyway it is straight forward simple. Good Luck. stealth

BroMikey
02-01-2015, 08:53 AM
The four reference names say it all. It was designed with the help of Bearden, Johnson and Cole. Bedini built the motor and did the testing, as well as I remember. The arm is iron or steel which attracts the magnets, then at the point where it travels past the steel arm, the magnet behind the arm repels the magnetic rotor. The steel arm is fashioned in a way so that as the magnetic rotor approaches it, It comes closer and closer to the arm, therefore it moves along in the attraction mode until it enters the point where the magnet repels it. It doesn't show it, but I would guess that a device is in place to prevent the rotor from turning backwards. Also you could add more arms and magnets to make it a stronger motor. The only limit is size and space. I don't know the date at which it was released, but I am speculating in the 1980's. I think John made a reference as to its working continuously somewhere. Anyway it is straight forward simple. Good Luck. stealth


Hi Stealth

I found a site where this information has been for some time now, I just never heard of this before now. I like John B and all of these other guys John learned from.

So you have our undivided attention. Sometimes I hear buzzing in the background but the air noise can be squelched:D.

Here is that site I should have found but just didn't.

Projects (http://www.callowayengines.com/msg26.htm)

http://www.callowayengines.com/att37.jpg


Bedini advanced motor - 06/08/01 (http://www.keelynet.com/bedmot/advmotor.htm)


It is at THE ICEHOUSE

MOTOR DIAGRAMS AND LAB NOTES (http://www.icehouse.net/john1/motor.html)


PETER PEREGRIUS MOTOR (http://www.icehouse.net/john1/peter.html)


http://www.icehouse.net/john1/hamel.html

BroMikey
02-01-2015, 08:56 AM
[QUOTE=Turion
The problem with this design is that .................................................. ........................[/QUOTE]

So did he (John) or didn't he make this run? I need a simple starting point.

You advanced men are light years ahead.:)

Mikey

Stealth
02-02-2015, 07:38 PM
I heard he did make it run. The problem is it lacks many measurements and tolerances needed to replicate. What is the rotor made of? What diameter is the rotor? What is the stator arm made of? How long and wide is the arm/stator? What are the magnets made of, what size and what strength? What is the distance between rotor and stator? Does it run better horizontally or vertically? At what angle are the magnets attached to the rotor? This the real reason many of these can't be replicated easily. The diagram only shows the actual motor but not he dimensions. This is one of the easiest magnetic motor to understand, but even as simple as it its, there are many experiments that would be needed to get it running. Trials and errors are what makes these things exciting. When you experiment with these things you will learn far more than if I tell you all the details. When I first started doing magnetic experiments, I quickly learned that the information I needed wasn't available in ant form(pre internet). So, I took a year out of my building and just experimented with magnets, every configuration, all difference shapes, strengths, sizes, and materials. After that years experiments and documenting everything, I wrote a book with these experiments. Good Luck. stealth

BroMikey
02-02-2015, 08:40 PM
I heard he did make it run. .................................................. .. I took a year out of my building and just experimented with magnets, every configuration, all difference shapes, strengths, sizes, and materials.

After that years experiments and documenting everything, I wrote a book with these experiments. Good Luck. stealth

Yes I agree experiments can be time consuming and complicated so documenting questions and answers is important.

Thanks for the run down on what questions I should be answering.

I am very shallow when it comes to understanding magnet motors, other maybe very deep into this subject. When I think about testing magnets I think about iron dust as a means to view results as changes are made.

Did you ever use dust? Did you put any of your magnet sets on glass?

I have found many puzzling reactions within these experiments so I have wondered if most advanced researchers might be using some kind of visual tool.

When I get up to the Radio Shack or Wal-mart I see small ones, like donuts and some square. The kids lost some of them but the 11 year old loves these experiments.

If only I could advance his and my understanding. That is what it is all about.

Thanks Stealth. I saw that huge wheel outside the backyard of someones house and I still think about it often. I think it is a gravity wheel but it could be a magnetic motor as well as it is a gravity wheel.

Did YOU post that? I still can't get over that big wheel.:thumbsup:

Mikey

Turion
02-02-2015, 08:41 PM
A long time back, probably 10 years ago, I built a magnetic device that ran for several weeks, before I didn't have room for it anymore, and took it apart. I hadn't figured out how to get any usable work out of it, but now I can think of a couple ways. Picture a child's see-saw. It will tip back and forth because it has a pivot point in the middle. Whichever side is overbalanced will tip down until it hits the ground. When one end is on the ground it resembles a long ramp with a pivot point in the center.

I put magnets in repulsion along both sides of half of the ramp (see saw) so it forces a roll of magnets to move up the ramp past the center point. The see-saw will tip, and the roll of magnets will now roll down the other side. The weight of the magnets in the roll would cause this side of the see-saw to tip down, where it should now come into alignment with magnets along THIS side which will force it back up the hill and past the center point again in the opposite direction. The see-saw would tip back and forth as the roll of magnets went up and down. This up and down movement will move the ramp into and out of alignment with the magnets on the side, I actually had wheels on my roll of magnets, but not out at the end. I also had HO scale train track on my ramp.

You could connect at the center pivot point to do usable work. The heavier the roll of magnets, the more work it will do. If this were designed like the linear magnetic gates that have been shown here, each half would be in repulsion mode sending the magnets in the opposite direction. An advantage would be that you can have a big POWERFUL magnet on each end that sends the moving magnets back in the other direction.

Just an idea...I should mention that one flaw in the design was that as the ramp came down and the magnets that were in repulsion came closer to each other, it would often "lift" the wheels off the track. I never figured out a way around this, although now I can think of a couple.

Dave

Stealth
02-03-2015, 12:01 AM
Your see-saw machine sounds familiar to one I designed several years ago, although mine was more like the drinking bird. With a magnet on the bottom and one on the top. Whenever the long lever(neck) would go up and down it would encounter the magnets at the end of each stroke causing the magnet on the lever to flip polarity, therefore sending it in the opposite direction. I also designed one to run on water with the same principle. Although I haven't built either one, I have run simulation on them and they should work as designed. The problem with this design is that it would take the better part of most peoples yard to build and run with enough energy to power a generator, or you could use a magneto like a windmill and produce power off the moving arm. Both of these designs should work great. I got frustrated with Radio Shack and started ordering my magnets. Seems they were always running out of them when I wanted to buy some. Good luck. stealth

BroMikey
02-03-2015, 07:49 AM
I looked all over for a teeter tooter magnetic engine but only found this. Well this is what we see on YOUTUBE. I am not ignoring you gentlemen it's just that I am not finding anything yet.

https://www.youtube.com/watch?v=lBB8puMtwJM

http://i.ytimg.com/vi/lBB8puMtwJM/hqdefault.jpg

BroMikey
02-03-2015, 08:07 AM
Okay I found this under MAGNETIC ENGINES

It is one form of teeter tooters but I don't know anything for sure.

Maybe you guys will figure the spinning magnets out.

https://www.youtube.com/watch?v=0yDfdngwPjA


http://img.youtube.com/vi/1210MxAOHfc/0.jpg

BroMikey
02-03-2015, 08:53 AM
Here are some important facts for motor builders.

http://i.ytimg.com/vi/2KMt9C1PAWc/hqdefault.jpg

http://www.theorderoftime.com/images/theorder/timeim/science/yildiz-arrangement.jpeg


https://d2t1xqejof9utc.cloudfront.net/screenshots/pics/382f615bd413fd421a47e6c8811d6ba7/medium.jpg

http://www.villesresearch.com/images/magnetmotor03.jpg


http://i1196.photobucket.com/albums/aa403/greeninventions/in8m9.gif

Stealth
02-03-2015, 07:05 PM
The teeter totter or see saw or drinking bird motor has not been shown on you tube before, and may never be shown. I don't do you tube videos and have not seen any such machines illustrated. There are hundreds of magnetic motor designs on you tube. Most are fake, with an external source powering them. Only a few are worthy of experimentation. My latest design uses gravity and magnetism to power the motor. Two independent wheels interconnected to over balance each other at 180 degrees apart. One other magnetic motor that does work is the "hamster cage motor". It uses gravity and magnetism to keep the wheel spinning. Good Luck. stealth

BroMikey
02-03-2015, 08:37 PM
The teeter totter or see saw or drinking bird motor has not been shown on you tube before, and may never be shown. I don't do you tube videos and have not seen any such machines illustrated. There are hundreds of magnetic motor designs on you tube. Most are fake, with an external source powering them. Only a few are worthy of experimentation. My latest design uses gravity and magnetism to power the motor. Two independent wheels interconnected to over balance each other at 180 degrees apart. One other magnetic motor that does work is the "hamster cage motor". It uses gravity and magnetism to keep the wheel spinning. Good Luck. stealth

Yeah I see a lot of garbage on the TUBE.

Good to see you out again Stealth.

I think two forces working together is an excellent thought, such as Buoyancy and gravity OR Gravity and Magnetism. Like John Bedini's flywheel on some of his impulse motors designs. John and others have shown how the flywheel is required to make the system function in the most efficient manner possible.

You see the first device that ever caught my attention was John's little LED MOTOR that ran for 3 years and I think about it all of the time.

Over balancing simulations are everywhere on youtube with it being almost nearly impossible to tell what is real.

How are you doing on your latest invention? Will it run some? For an hour?

I will look for gravity engines coupled with magnetism but I have already done that for years with no results. First what i find is free energy on the video and the next thing you know they are collecting water from a huge mountain stream.

The Tube is full of people joking around seeing who will believe their lies also.

A person has a hard time telling what's real and whats phony.


I will look at the OVERBALANCING stuff I can find.

Mikey:thumbsup:

Turion
02-04-2015, 05:51 PM
Here is the problem with all these YouTube videos
Here is one an individual claims works
https://www.youtube.com/watch?v=XKtIsrc-LHs

and here is a guy who replicated it who says it doesn't
https://www.youtube.com/watch?v=H9p6K4UehuA

Who do you believe?

Stealth
02-04-2015, 07:46 PM
The second video, the replication is the real one. Magnetic motors won't work in that configuration. Even magnetic/gravity motors won't work in that configuration. Many so called free running magnetic and or gravity motors on you tube are fake. There are many people trying to manipulate people minds by showing what appears to be continuous running motors that do not work. Almost always there is a power source nearby, out of the picture, powering these machines. With some major modifications it may be made to run. There are many hoaxers and disinformation people out there for whatever reason. Knowing that you can only replicate a small portion of these machines, it pays to be very wary of which ones you choose to replicate. Often it is virtually hard to tell which ones are legitimate and which ones are not. Some of these videos are created by people who are good at making videos, not machines. This is the very reason I don't do videos, although I occasionally do a still shot, camera picture, but even those can be altered to show something fake. This is why if I do a camera shot, I use a 35mm film camera. Good Luck stealth

Peter May
02-04-2015, 08:01 PM
Saw this on overunity.com and I have a feeling this fellow might be on the right track.

YouTube - Magnet Motor Prototype (http://www.youtube.com/watch?v=jZjEYu9BbW0)

The problem I have seen with all permanent magnet motors so far is that everyone keeps thinking in two dimensions which is a big shortcoming.

This fellow has expanded into the third dimension and you can already see improvement over those two dimensional spiral motors.

I would take this a few steps further (or turn it up couple of notches :) ). Instead of a cylinder use an inverted cone (apex down) so that we have a vortex/spiral, and pieces on the cone are constantly spiraling or "falling" down into the vortex. I remember reading about David Hamel and his revelations where he said that his device is all about being out of alignment and constantly "falling" so that clicked in right away after seeing this.

As magnets are a force, how can they prrovide energy
Can you show a detailed electrial diagram

BroMikey
02-07-2015, 07:26 AM
Here is a good one both gravity and magnetic

Did you miss that one guys?;)

https://www.youtube.com/watch?v=eDPrQZiiQA8


http://i.ytimg.com/vi/OhrFtWlkIJQ/hqdefault.jpg

BroMikey
02-20-2015, 01:14 AM
Amigo's your new motor design is here. It uses gravity too.



Surge Tech- Magnetic motor


https://www.youtube.com/watch?v=qf-AgSVOl38


https://www.youtube.com/watch?v=NFMOvHEDkj4


http://i.ytimg.com/vi/w_MWVPhLeWc/0.jpg

BroMikey
02-25-2015, 08:02 AM
Permanent magnet motor principles.

https://www.youtube.com/watch?v=yDlplL-Jicc

http://i.ytimg.com/vi/yDlplL-Jicc/hqdefault.jpg

https://i1.ytimg.com/vi/zdMcrnYY6vY/hqdefault.jpg

BroMikey
03-23-2015, 01:22 AM
Somebody did it again

https://www.youtube.com/watch?v=2vFK12ohRmY

http://jackh.pbworks.com/f/1179282843/Jack01.JPG

BroMikey
03-23-2015, 01:52 AM
Magnetic engine low volts

https://www.youtube.com/watch?v=Y2iSlT2wxHA

BroMikey
04-05-2015, 01:05 AM
Oscillator magnet motor with air coils reoriented for
gating effects. free running.

https://www.youtube.com/watch?v=ztRr-dUs6EU

BroMikey
04-05-2015, 01:12 AM
Here is the answer to the video also another invention

https://www.youtube.com/watch?v=94Jz8AS_Yoc


http://flyer.thenetteam.net/freeCirk.jpg


http://flyer.thenetteam.net/freeCirk2.jpg


http://flyer.thenetteam.net/freeCirk3.jpg


http://flyer.thenetteam.net/freeCirk4.jpg

vidbid
04-05-2015, 04:11 PM
https://www.youtube.com/watch?v=KhY7hHb2l6o



https://www.youtube.com/watch?v=KhY7hHb2l6o



' looks like it might work.

BroMikey
04-23-2015, 07:55 AM
Butterfly effect motor free energy


http://www.icestuff.com/~energy21/ngnr.jpg


IceStuff.com: Bedini IDEAS AND MOTORS from The Encyclopedia of free energy,energy21.org,energy 21 org ,Geoff Egel, (http://www.icestuff.com/~energy21/bedid.htm)


http://www.icestuff.com/~energy21/ngnr.jpg


http://www.icestuff.com/~energy21/ron1.jpg


http://www.icestuff.com/~energy21/jon2.jpg



Test 1 Input Power 25.4 Volts at 3.90 Amps= 99.00 Watts , Output Power 48 volts No Load

Test 2 Input Power 25.3 Volts at 3.90 Amps= 98.67 Watts , Output Power 28 Volts .75 Amps= 21 Watts at 37.33 Ohms

Test 3 Input Power 20 Volts at 3.39 Amps= 67.80 Watts , Output Power 50 Volts at 3.70 Amps= 185.19 Watts at 13.50 Ohms

Test 4 Input Power 21.9 Volts at 2.30 Amps= 50.37 Watts , Output Power 20 Volts at 31.75 Amps= 634.92 Watts at .63 Ohms

BroMikey
05-08-2015, 09:58 AM
Another free energy motor

This one is for Level

https://www.youtube.com/watch?v=VkBGfcZjXvM

Joit
05-08-2015, 10:38 AM
Another free energy motor

This one is for Level

https://www.youtube.com/watch?v=VkBGfcZjXvM

You didnt watch it until the end where he uncovers his fake?

BroMikey
05-23-2015, 11:02 PM
Magnet motor

https://www.youtube.com/watch?v=Wys41ESJEIA


https://www.youtube.com/watch?annotation_id=annotation_4137781219&feature=iv&src_vid=Wys41ESJEIA&v=dpYlZL3tc8k


https://www.youtube.com/watch?v=vgXxTrK5GO0

citfta
05-24-2015, 12:32 AM
Those are some nice videos if you want to make a generator for a windmill. But they have nothing to do with a magnet motor. :confused:

Magnet motor

https://www.youtube.com/watch?v=Wys41ESJEIA


https://www.youtube.com/watch?annotation_id=annotation_4137781219&feature=iv&src_vid=Wys41ESJEIA&v=dpYlZL3tc8k


https://www.youtube.com/watch?v=vgXxTrK5GO0

BroMikey
05-24-2015, 03:31 AM
I guess I should have found a better spot to put the magnet generator
that some are using like a Muller Motor.

I just thought it was a good video and should let people decide for
themselves what to do or which way they want to go with magnets.

Those huge neo's are pretty expensive little devils:mad: I heard
one guy say he paid $100 a piece for his toy project motor/Generator
build with the start style coil windings.

You are far more advanced than I on distinguishing the different type
of ideas associated with many designs. There are just so many variations
I get lose in thought and wonder where to put all of these approaches.

When I look at the windmill motor there I see Muller and think it is a
shame only Muller can make it do both.

I am still hoping.

Thanks for asking what I was thinking when I posted the video.

May God bless you.:cheers:PS here is the same idea

https://www.youtube.com/watch?v=jzO0-p0NF7E

BroMikey
05-24-2015, 03:51 AM
Lasersaber replication of the Muller Generator.

I mean Motor/Generator. Magnet Motor/Generator:thumbsup:


Now thats what I mean.

https://www.youtube.com/watch?v=2KaVcmXyktw

https://www.youtube.com/watch?v=CVT5ZleK5rY

https://www.youtube.com/watch?v=maaWoAmErxE

https://www.youtube.com/watch?v=R9i8_CFZtfo

BroMikey
07-07-2015, 08:02 AM
Amigo the new motors are here.:)

The Extra energy is here:) No foolin

https://i.ytimg.com/vi/C4FcdPsp-aE/mqdefault.jpg

https://www.youtube.com/watch?v=bcEClN2Gsf0

https://www.youtube.com/watch?v=6SM55gtAGrQ

https://www.youtube.com/watch?v=iCu3_dVMERI



http://www.energeticforum.com/redirect-to/?redirect=https%3A%2F%2Fi.ytimg.com%2Fvi%2FC4FcdPs p-aE%2Fmqdefault.jpg

BroMikey
07-11-2015, 08:19 AM
Here is an improved version of a demonstration John Bedini gave
for a free energy magnetic motor. Amigo's the motors are in.

https://www.youtube.com/watch?v=4fr49GmHjnc


https://lh3.googleusercontent.com/proxy/0lF1v2uG8VJkMRnOq7HKVLdcinRsP7xVo-MXgCo04mo5uhjQlnBF22CL5_NRh4t_u3zxC9_D4COnyd28euNp =w426-h240-n

Stealth
07-11-2015, 06:03 PM
This design has a lot of potential. If the angle of the magnets are correct and the degree at which each magnet in the rotor repels the magnetic stator, then there is no reason this will not self run. The easiest way to approach a magnet with another magnet is to approach at an angle and slanted. This will give you the least resistance. Then after it passes the neutral zone, at the halfway point, it will the repel it out the opposite end. It is simple, (you can try this at home), just take two magnets, fix one on a flat surface with tape, the try holding one ion your hand a approach it and feel the resistance. Then try angling it and turning it at angle and feel the difference. Good Lu8ck. stealth

BroMikey
07-26-2015, 05:10 PM
magnet motor design ideas

https://www.youtube.com/watch?v=C7RXOhfsjDA


http://www.linux-host.org/energy/mag2.gif

BroMikey
08-06-2015, 05:09 AM
Stepper motor self oscillation




https://www.youtube.com/watch?v=k6p-qWZ4r0A



http://v008o.popscreen.com/VWtlRkg1TWwxUlEx_o_free-energy-generator---magnetic-motor-plans-that-.jpg


https://s-media-cache-ak0.pinimg.com/236x/66/ba/a4/66baa4bb01ea228fb1b21072aa19026f.jpg


http://www.oocities.org/frenrg/ce2.jpg



http://i.ytimg.com/vi/2qJP4rGfv7o/hqdefault.jpg

BroMikey
08-24-2015, 02:03 AM
Here we see revealed a Magnet motor or magnet engine.

Everyone has a new motor these days so we will have to start

a thread for each idea. I the mean time we are still not seeing

any useful motors on the market after 80 years of brain storming.

Just another motor that will pass with the inventor.:rolleyes:

Isn't it a shame the way men can never seem to get along

and work together. It's just hate pouring out like a stream.

An to prove this out the only time you hear from certain men

is when they can spread some more of their hate message

of self-righteousness. That is they are righteous and when they

open their mouths to destruct (Not instruct) they let you know

where and how you missed it. Of course mud slinging and so

forth. Other than this you won't hear from them because this

is all they have to offer. Isn't it a shame?:rolleyes:

I need not name them, they ID themselves every time the speak.

But do mark them.


Magnet Motor Engine



Published on Mar 22, 2015

In this video i show that the orinithopter engine charge the capacitor, there is the linear movement that need to connect to coil for more power and volts or connect it to crank shaft flywheel for mechanical movement,
This is the ornithopter engine
This engine used 12v battery and electric motor!
For future use The system is the heart of some of the large system, the heart of the system is significant to run a big machine,By some few volts can operate the machine, and by so , can work long hours!! or days (2 stroke magnet engine! For example motors sketches!) Shows that can be moved by magnets without gears or belt or any connection! and use a small electric motor, and low power consumption and heavy crankshafts rotate high speed without any contact, Since there is no friction between the parts of the magnets and do not touch each other! No warming! not need gas gasoline or diesel ,only battery
A machine that works with a huge magnetic force, Centrifugal force, a linear movement,Magnet crankshaft is not connected!
After the examination, the value of this invention is $ 200 million ,
If you decide to copy it making it possible that you pay the price of $ 200 million ,
This engine Patented invention
made by oren gertel
gerteloren@gmail.com




https://www.youtube.com/watch?v=wSEXjXLk9rg

BroMikey
08-24-2015, 02:13 AM
Here is another Revelation called by the mans name

or we could say NEW MAGNET MOTOR.



Tittle

Wasif Kahloon Revelation


https://www.youtube.com/watch?v=fn7nn9p-7GU

BroMikey
08-24-2015, 02:18 AM
Magnetic Motor Revealed.

Another revelation another principle.

It is really not new but we will let him think so.:)

Just like all of the young up starts who think they

are the first ones. It's mine, it's mine and then you don't

see them anymore because they are to old.:rofl:




2. Motor Magnetico Mexicano - Secreto Revelado -


https://www.youtube.com/watch?v=VVHlWRItuZE

BroMikey
08-24-2015, 02:29 AM
Magnet Motor Techy:)

More revelations that are very very clear.

https://www.youtube.com/watch?v=duhCvHQDz1Q

BroMikey
08-24-2015, 02:34 AM
Not just a mere "Revelation" but "THE HOLY GRAIL" of

magnet motor secret technology. What a silly way to get

attention.

As shown in this video, one way magnetic shielding is the holy grail to building a working self running magnetically driven motor. Build it yourself and watch how well it works.

BTW: There is a glitch in the video here just after 2:14. This is not an edit. The original video played back just fine. Possibly it's an upload glitch? I'll check my hard-drive and see if I have a glitch free copy, as I originally used my cellphone to make this video, of which I no longer have.

Note: People on Youtube are now replicating my work with great success, including this experiment as well.

Have you seen this video?

YouTube (http://www.youtube.com/watch?v=XePk5E)...

Cheers!

I'm now storing/archiving my info for long term storage using, Google sites.
Top Magnetic Generator - 100% Free Plans (Open Source) (http://www.Top-Magnetic-Generator.com)
Pleaseee pass the link around. Thanks in advance!


https://www.youtube.com/watch?v=IlMBZJEtwRQ



https://www.youtube.com/watch?v=ZZOnSaBvxUg

BroMikey
08-24-2015, 02:47 AM
New Concept or shall we say NEW revelation?:)

There are many ideas, maybe we need to dump the

people stringing us along with promises that never

come true.


https://www.youtube.com/watch?v=Wj_A06WjlbU


https://www.youtube.com/watch?v=wB9trhNH7PY

BroMikey
08-24-2015, 03:20 AM
Magnetic Monopole Magnet motor principles revealed.:)





By xee2vids
Published on Oct 12, 2013

The magnetic domains in the 1018 steel easily align with the applied magnetic field. The domains on each side of steel cube align with the magnetic field at that side. Thus both magnets form attractive forces
with the steel. Any material with easily rotated magnetic domains will
work.

https://www.youtube.com/watch?v=6iEnQw2Wt7w

BroMikey
08-26-2015, 07:54 PM
Zero cogging patented magnetic motor

https://www.youtube.com/watch?v=r3JRVQ58CZA

Turion
08-27-2015, 07:59 AM
This really isn't a permanent magnet motor, but an idea for a magnet ASSISTED motor that uses the repelling force of magnets to add energy to the rotation of the shafts.
https://www.youtube.com/watch?v=XM9R3qpIPJc

BroMikey
08-27-2015, 08:18 AM
This really isn't a permanent magnet motor, but an idea for a magnet ASSISTED motor that uses the repelling force of magnets to add energy to the rotation of the shafts.
https://www.youtube.com/watch?v=XM9R3qpIPJc

I am watching everything and yes your video is what is on the table

with Mack's discussion. I couldn't have done a better job to explain

or illustrate. Keep good data records Dave, thats what I want to tell

you. You are leading edge and with so many variables. What a great

experiment. So many coil versions over in your coil thread.

I have very high hopes, especially the rewound scooter motor

with increase COP greatly. Multiples upon multiples of COP's.


A permanent magnet motor can be any motor with heavy rotating

magnets. Motors without these magnets or not.:cheers:

A beginner perspective what can I say.

I will be looking for better results as you have the time and money:thumbsup:

Sweet deal for all of us.:thumbsup:

BroMikey
09-04-2015, 08:34 AM
Old 1950's magnet motor footage.


https://www.youtube.com/watch?v=WQuWae2yWi4

BroMikey
09-05-2015, 09:33 AM
3D printed magnet motors.

https://www.youtube.com/watch?v=tVXAX_z437U

BroMikey
09-07-2015, 06:26 AM
Amigo's your poor mans magnet motor is in.

Guys, do you really want to build working magnetic motor ? Or is that just a funny game here ? :(

https://i.ytimg.com/vi/HWuXvZFn91Q/hqdefault.jpg


https://www.youtube.com/watch?v=qNBgcrUTNgk



https://www.youtube.com/watch?v=GEogsEfFXrg


https://www.youtube.com/watch?v=BkGElmxZmhk


https://www.youtube.com/watch?v=HWuXvZFn91Q

BroMikey
09-08-2015, 07:47 PM
The latest Magnet Motor running demo.

https://www.youtube.com/watch?v=20LrW-8eDY4

BroMikey
09-11-2015, 07:38 AM
Magnetic Motor (Flux 1.75)



https://www.youtube.com/watch?v=eT0UR7bL7Mk



https://www.youtube.com/watch?v=ScaMDw82ujo




https://www.youtube.com/watch?v=fyYqZYnd02A

BroMikey
09-13-2015, 01:50 AM
Published on Sep 11, 2015

Crank wheel connection option with or without magnets,
Machine speed causes the production of electricity by generators,
Battery Charge option! Capacitor load option! And movement options!
THIS IS Mechanical Sketches Demo VIDEO! Magnetic Fields IS Not Visible!!! There is many configurations that can do with this Ornithopter Engine That Invented & Patent by GERTEL OREN!
The invention can be used for straight or boost engines, & rotation engines! You can use it for boat engines, Wings engine could also fly with wings! Economical use with no mechanical wear!! And for any purposeֱ... Scooter engines , bike engines, energy engines combined with vibration!-_-!
My name is Oren Gertel and i build this magnets engine!! It's all for a better future in the energy sector soon! magnets and magnetic machines!! hard work was to build a machine like that! I do not try to hide anything in any of these invention! This "mechanical sketch" that can shows the capabilities of this engine in the future!!
This Is The Ornithopter Engine
This engine used battery and electric motor!
For future use The system is the heart of some of the large system, the heart of the system is significant to run a big machine,By some few volts can operate the machine, and by so , can work long hours!! or days (2 stroke magnet engine! For example motors sketches!) Shows that can be moved by magnets without gears or belt or any connection! and use a small electric motor, and low power consumption and heavy crankshafts rotate high speed without any contact, Since there is no friction between the parts of the magnets and do not touch each other! No warming! not need gas gasoline or diesel ,only battery
A machine that works with a huge magnetic force, Centrifugal force, a linear movement,Magnet crankshaft is not connected!
After the examination, the value of this invention is $ 200 million ,
If you decide to copy it making it possible that you pay the price of $ 200 million ,
This engine Patented invention
made by oren gertel
gerteloren@gmail.com



Testing apparatus Magnets endless possibilities

different connections Oren Gertel

https://www.youtube.com/watch?v=K32y17yqiHA

BroMikey
09-13-2015, 03:26 AM
Respectfully magnetic toys




Published on May 7, 2015

This video explains how magnetism is actually caused by the Magnetic Spin Vortex. It covers what the spin vortex is, and it is not, and the importance of understanding it in the field of Permanent Magnet Motive Force Systems.



The Magnetic Spin Vortex

https://www.youtube.com/watch?v=Gd2IyoBl2ag

BroMikey
09-13-2015, 08:03 AM
Self rotating magnetic motor Free energy


https://www.youtube.com/watch?v=tpv1op4yHm0

BroMikey
10-04-2015, 04:56 AM
Amigo's Magnet motor explanation.

https://www.youtube.com/watch?v=11OWgnug1_4

BroMikey
10-20-2015, 06:46 AM
Car Motor size magnetic Motor.




In Conclusion

This is a unique system that will grant you a huge deal of electrical independence. You will save more than 80% from your bill every month. It can be built with simple materials with a cost as low as $100. It will work all year long, and much more, so that you do not have to worry or keep investing money on it. More than 30.000 families have already benefited from this product. Now it is your turn!:thumbsup:


https://www.youtube.com/watch?v=h60QiRYUZqA

BroMikey
11-08-2015, 08:34 AM
Magnetic motor

JLN Labs - RGen 2.0 (Rotating Generator) (http://jnaudin.free.fr/html/rgen2.htm)


JLN Labs - RMOD V1.1 (http://jnaudin.free.fr/html/rmodmk1.htm)


http://jnaudin.free.fr/images/rmod1anm.gif


http://jnaudin.free.fr/images/rgen2.gif

Aaron
11-11-2015, 01:35 AM
Respectfully magnetic toys




Published on May 7, 2015

This video explains how magnetism is actually caused by the Magnetic Spin Vortex. It covers what the spin vortex is, and it is not, and the importance of understanding it in the field of Permanent Magnet Motive Force Systems.



The Magnetic Spin Vortex



I posted a simple comment on that youtube page - pump the bottom one with the top one up and down and NOT side by side. I spent countless hours over 3 months on these spinners before I ever tried to build the original SG - that was 16 years ago.

To me, it is like this toy but magnetically - that is what I found anyway:

http://www.yoyomuseum.com/images/profiles/PumpTop.jpg

BroMikey
11-11-2015, 02:17 AM
I posted a simple comment on that youtube page - pump the bottom one with the top one up and down and NOT side by side. I spent countless hours over 3 months on these spinners before I ever tried to build the original SG - that was 16 years ago.

To me, it is like this toy but magnetically - that is what I found anyway:



Hi Aaron

I must be thick because I do not understand your comment. But I am
having flashbacks of Xmas 1963.:D Just kidding had to throw that in
because I buy the children a top when I can still find one.

I have always loved to watch a top spin, still do. I have been thinking
about John's concave rotor magnet assemblies from the conference
2010 Ferris Wheel bright red saying something like this to the audience

"You want to know why you don't have what I have here in this example?"

The magnet spin vortex and the SG have always intrigued me. I would
love for you to explain anything about this post more clearly as it directly
relates to both magnet motors AND those awesome coils with their
own capacitance.

Good to talk with you Aaron.:thumbsup:

Stealth
11-12-2015, 12:46 AM
Here is one to ponder. Youtube. Insane accidental discovery with neodymium maqnets. Free energy? After you calculate the energy needed to lift that stack of neos, then calculate how much energy is used to keep it running, I think this could qualify as a free energy magnetic motor. Simple, functional and efficient. All we need to do is build a large one big enough to draw energy from it. Good Luck. stealth

BroMikey
11-12-2015, 01:24 AM
Here is one to ponder. Youtube. Insane accidental discovery with neodymium maqnets. Free energy? After you calculate the energy needed to lift that stack of neos, then calculate how much energy is used to keep it running, I think this could qualify as a free energy magnetic motor. Simple, functional and efficient. All we need to do is build a large one big enough to draw energy from it. Good Luck. stealth

Hey Stealth

I see the top but I do not understand how neo's play in. Do you have
a video link? :)

Have a good one.

Yeah I saw this.

https://www.youtube.com/watch?v=KJHlwJ1gsms


https://www.youtube.com/watch?v=BR8RPstRN-E


https://www.youtube.com/watch?v=x9gdCnGniIs

BroMikey
11-12-2015, 09:13 AM
I spent countless hours over 3 months on these spinners before I ever tried to build the original SG - that was 16 years ago.



In 1997 when that video was made I was 40 years old. So you were 24 years then? The old picture. Time flies when you are having fun.

What stood out was the idea of a "ramp" these motor schemes all use
some form of a "RAMP" be it made of metal or magnets. I am just now
seeing how a wide variety of "RAMPS" are used in many motors.

The picture "GIF" animation above is like most proof work only showing
one piece of the larger puzzle.

Thank again Aaron.

BroMikey
11-28-2015, 10:04 AM
Magnet motor belt driven.



https://www.youtube.com/watch?v=k-AHiHXPdig


Published on Apr 1, 2015

Rotors = 3:1 (The mini are 1/3 the diameter of the big rotor = .33)
12:4 = 3:1 (Number of Magnets)
45:15 = 3:1 (The rotors swap neutral every 15* and every 45* they reverse direction on the graph)
90:30 = 3:1 (Magnets Spaced) (90* out of a 30* clock = 60, 45 and 15 sec)
180:60 = 3:1 (Equilateral Triangle) (60 60 60) 666
360:120 = 3:1 (Mini Rotors Placed)
3:1 timing belt is probably required! (Disconnect capacitor drive)

BroMikey
11-29-2015, 09:13 AM
Magnet motor designs

Ville's Research (http://www.villesresearch.com/magnetmotors.html)


http://www.villesresearch.com/images/magnetmotor02.jpg


http://linoavac.no.sapo.pt/electrorepulsion2.jpg


http://linoavac.no.sapo.pt/electrorepulsion2.jpg


magnetic motor magntico, magnet motor, free energy, moteur magntique,moteur magnetique,motor magntico,pricipio magnetico tringulo/quadrado, (http://linoavac.no.sapo.pt/)

http://linoavac.no.sapo.pt/magnetrotor.png

SisMika
12-04-2015, 08:25 PM
https://youtu.be/VmdH0AYi3WU

BroMikey
12-04-2015, 08:38 PM
The real secret to PM motors

https://youtu.be/VmdH0AYi3WU

They stole your design, Hey? But you caught them. Now go
ahead and make the money. Where can I buy your motor plans?:rolleyes:

I know, I know you are the guy that knows everything so why even try.:D

Still thinks he's one of a kind.:rofl: Here let me give you what you want

E=M*C2

Happy Now?:D Where is that rattle?;)

BroMikey
12-17-2015, 04:37 AM
Hello group members
Today were are graced with the privilege of watching the joy
of another mans project motor. Have fun.:thumbsup:

https://www.youtube.com/watch?v=GFYMa8cnolU


Published on Nov 22, 2015

Mueller / RomeroUK with New Magnets, Neodymium 8 Magnets, of 2 x 20 mm Diameter x 10 mm Thick, as Motor Only.

2 x Coils as One Coil for Motor, 2 x Coils as One Coil for Trigger.

The rest of the Circuit is yet Bedini Style, the Red LED is Lighted when the Motor Coils are Powered, Negative Rail on Oscilloscope, the White LED is Lighted on Collapse EMF and Generator of the Motor Coils, the Positive Rail on the Oscilloscope.

Components :

- Transistor : Silicon NPN 2N4401
- Diodes : 1N4148
- Coils all 4 Coils are 0.2mm Emaeled Copper Wire, about 12 mH each.
- Cores : 2 x 9 Ferrite Cores, 5.5 mm diameter about 60 mm Length
- Magnets : Neodymium 8 Magnets, of 2 x 20 mm Diameter x 10 mm Thick, N52

Characteristics :
- Motor Coils work in Attraction Mode
- RPM : 40 Hz / 8 = 5 Rotations per Second so about 300 RPM / Rotations Per Minute
- Operating Voltage : 12 Volts
- Power Consumption : not measured yet

--

Update / 2015-11-23 21:06 :

- Power Consumption : 58 mA @ 11.58 Volts so about 0.67164 Watts ~ 670 mili Watts.

With a "Better Version" of Command : 2 x Monostables, 2 x Motor Coils and 8 mm Diameter Magnets I got ~ 72 mili Watts, so, as it is this is way worse.

Let's see it when the PIC Commander will be in effect. Stand by...

BroMikey
12-17-2015, 04:46 AM
Amigo the party is just beginning so don't miss this one.
His work is based on the Howard Johnson stuff

The man says he is not going to be on youtube anymore
because people are calling him a fake and attacking him at
overunity. He made the excuse that humanity must not be ready
for this break through.

this one is Mylow

he was Not a fair player and was caught with a "string/thread" drive
in the Vid [I think Tinsel found the spot where you could see it ...
might have been member Wattsup at OU.com ??

been awhile ?

It was clearly visible under magnification.

Chet


https://www.youtube.com/watch?v=aElDTxiOEas

https://www.youtube.com/watch?v=AHkC2gIVljM

RAMSET
12-17-2015, 11:03 AM
this one is Mylow

he was Not a fair player and was caught with a "string/thread" drive
in the Vid [I think Tinsel found the spot where you could see it ...
might have been member Wattsup at OU.com ??

been awhile ?

It was clearly visible under magnification.

Chet

BroMikey
12-18-2015, 07:58 PM
this one is Mylow

he was Not a fair player and was caught with a "string/thread" drive
in the Vid [I think Tinsel found the spot where you could see it ...
might have been member Wattsup at OU.com ??

been awhile ?

It was clearly visible under magnification.

Chet

Thanks Chet I sort a remembered that name MYLOW but I posted
so many videos I am not sure which video to tag as a trick.
If it was the last video I posted let me know.

I will put your post right on the video too.:thumbsup:

RAMSET
12-18-2015, 08:23 PM
The Vid of the array on a desktop with the Lamp to the right.

I do believe Mylow never started out to deceive ....he just felt perhaps others could get it working since it was obvious it _could_ work [obvious to "him"]

I have seen this happen many times ,persons give what they feel is a gift
of an idea they are certain will work ....but never actually got working
Mylow went one step further....
I believe there are fellows that feel MadMack May have done this with his
experiment.

I personally do not feel that way about Mack ,but these types of things [Mylow} embolden critics to make assumptions.

I saw that you asked about my absence from the forums of late ?
these have been very tuff times with family crisis and commitments and also
with persons/Gov'ts outside my control trying to control open source research in the field of free energy.

Very odd times indeed... especially when you look at where LENR has been
going lately .

respectfully
Chet

BroMikey
12-19-2015, 02:19 AM
I saw that you asked about my absence from the forums of late ?
these have been very tuff times with family crisis and commitments and also
with persons/Gov'ts outside my control trying to control open source research in the field of free energy.

Very odd times indeed... especially when you look at where LENR has been
going lately .

respectfully
Chet

Oh yeah I remember now, that you mentioned that before. LENR? Sounds
like HHO gas research to run engines is tickin off the big wigs. The people
I listen to say that in the larger metro area's electronic surveillance used
to gang stalk persons is ramped. Pain can to inflicted upon your body
when 1,2 and 3 cell phone like devices are used to triangulate on any
targeted point.

Smart meters can be used against you to create an atmosphere of dirty
EMF in your home. It is possible to make a person sick or injure them.
The constitution forbids the controllers to shut down free persons by the
use of force so a more indirect force is being beta tested.

Biological systems are being mapped out and redirected through the use
of nanobot or nano tech where chemtrail spray out a smoke like looking
dust (SMART DUST) and the life on this planet will breath it in. These tiny
machines are in contact with the super computer A.I. like we saw with
JADE HELM at the helm. They are literally manipulating every living system
that can be controlled. To what degree is progressing very rapidly.

These new machines can connect our minds to a PC and are being
advertised for the future generations now. The chips are not needed
to get the job done. If you are in a highly congested area of the
country GET OUT away from the masses, if possible.

Truth is stranger than fiction, I know.:suprise:

I will pray. You rest fearless, do you understand? Fear is a weapon and
gang stalking depends upon it. Rest easy and trust in God and they have
no power over you. Panic, show signs of elevated stress and the turn
up the heat till you crack.

This is the way I heard that this stuff is going down.:cheers:

I posted the patents somewhere showing that this is just like I say.

BroMikey
01-06-2016, 05:13 AM
Amigo's

Chinese Magnet Motor solves the problem of triggering when
using double rotor double triggering. Double trouble.

He has other video's on this but I like this one best
because he stops it and shows you the operation.

Notice the centering post is a nail that seems crude not
very precise? This may be use to get it started while the
rotors become self centering. They may wobble as well
taking advantage of gravity.

This is what we always say, that the triggering part moves
and if it doesn't move the rotor stops right? Well the trigger
moves and wobbles one against the other fulfilling
each others needs to run.



https://www.youtube.com/watch?v=PBVN5mkYqpo

Turion
01-07-2016, 04:47 AM
From Steele Braden:
In the attached video, is another method of making magnets work for you!
The track, uses common off the shelf ceramic magnets unmodified in any way.
The roller on the other hand is specially made.

Thought you may be interested in an experiment I did about 15 years ago.
This linear “motor” is 650mm long.
As you can see in the video, the roller is self-starting upon release.
It would travel much further with a longer track, and indeed till it ran out of track magnets!
If the track is positioned so that there is an incline towards the end of 10 degrees, the roller still travels along the entire track UP HILL!!
It occurred to me that if the track were to be made say double the length, enough height would be gained for recycling.
That is, the roller would drop off the end of the track onto a return shute, to be deposited back at the beginning of the track.
So far, I haven’t tried this, but it is certainly a possibility.

The underside still shot shows the arrangement of the ceramic magnets.
These are set at 45 degrees like fallen over dominos.
All in attraction mode.
After umpteen experiments, I found that a maximum of 5 track magnets must be used, then a gap of one magnet thickness (wooden spacer) then the next set of 5 magnets etc.
If more than 5 magnets are used per set, the forward magnetic field changes, and the roller stops rolling.
The secret to the travel, is that the leading half of the roller has far more field force acting on it than the trailing half.
So the roller is always in a state of unbalanced field.
This becomes like a dog chasing its tail.
The roller is a special component.
It has a non-magnetic cylinder enclosure of stainless steel 1mm thick.
In it, are 20 neodymium magnets all wedge shaped.
This produces a North only emanating from the outside surface, whilst the South, is internal in the central hole.
So the South, cannot be “seen” from the roller.
This was specially made up to my specifications.
It produces in effect, a unipolar magnetic roller.
This is essential for its operation.
Having said that though, you can still get the system to operate WEAKLY, by using an empty baked bean tin as the roller. (ferrous can).
It still runs, but with very little torque, unlike the special roller which has “heaps” of torque.
You will never find a unipolar magnet roller “off the shelf”!!
The 20 magnets in the roller, were particularly difficult for the engineer to assemble into the stainless cylinder, as they “fight” like mad against each other, being in repulsion with their neighbours.
Being neodymium however, even though hard up against each other, the field still does not get “killed”, as would be the case with weaker ceramic magnets.
After a lot of bother, we put together a rotary version of this concept.
However, it refused to rotate!!
This required large wedge shaped neodymium magnets made up as the stators.
I still hold some hope for this idea, but it is very definitely “on the back burner” at this time.

There is no resistance at the start of the track to the roller starting.
As soon as I release it, it “takes off” and is very keen to get away.
There is a very slight arrest force as the roller travels over the wooden gaps in the track, but so little, as to be no problem.
I am sending you a scan of a drawing showing the construction of the roller.
The centre hole (without the nylon tube inserted) is twice that of the Neodymium magnets South/North measurement.
Finally, a coating of epoxy resin glue is put over the ends of the completed roller to ensure that they stay in place.
If you intend building this, I have some 20 or more spares laying around here someplace I think, that you would be very welcome to at just the cost of the airmail postage.
To assemble the magnets into the stainless steel cylinder, do the following.
Fit first at 12 oclock, then 6 oclock, then 3 oclock, then 9 oclock, then the rest.
They try to pop out if you do anything else, until all are finally inserted.
The stainless steel cylinder is of non-magnetic grade.
This is important, as the field needs to be able to emanate unrestricted.
You will need to get an engineer to decide the inner diameter of the stainless cylinder so that the magnets when fitted inside, are fairly snugly together.
Avoid gaps between magnet segments if possible.

Construction of "unipolar" roller with 20 segmented Neodymium wedge shaped
magnets.
This was done because a single Neodymium magnet of the shape could not be
made (magnetised) as I required it, hence the need to produce the same
magnetic orientation with 20 small magnets.



linear motor_zpsqccvziwo.jpg Photo by David_Bowling | Photobucket (http://s34.photobucket.com/user/David_Bowling/media/linear%20motor_zpsqccvziwo.jpg.html?o=0)
scan0035_zpsndqpzwiv.jpg Photo by David_Bowling | Photobucket (http://s34.photobucket.com/user/David_Bowling/media/scan0035_zpsndqpzwiv.jpg.html?o=1)
https://www.youtube.com/watch?v=VOLcWLmbgR4&feature=youtu.be

That is the info I have so far. Ays will notice, this takes SPECIALLY CUT magnets on the rolling piece (rotor). Steele has been kind enough to put enough in the mail for me to complete a rotor of my own so that I can replicate and publish my results here. I will let you all know what happens.

Dave

BroMikey
01-07-2016, 06:28 AM
Hey Dave

I am thrilled to understand this design, thank you. You know
why I liked it so well? Because it deals with cancellation.
See what I mean?

The south's all point in, right? and they are the points on the pie
shapes. The roller has a huge amount of cancellation forces
trying to fight their way outward. (This is so cool I could leap)

See what i mean? Well I am repeating myself when I should be
working harder at explaining what I see. I see scores of magnet
video's and there is always something to be learned in them.

I look for youtube video's in other countries because they don't
talk but the video says it all.:) I your case Dave the description
you made is a good one I can wrap my head around easily due
to your ability.

I won't say I can setup another experiment right now but thank you
anyway for your offering. There must be a young experimenter say
30-40 years who might try it.

I always envision forcing magnets together in cancallation during
the day when i am working just playing head games til the 5'oc
whistle. The pie shape cancellation picture you painted has me
doing metal jump rope.:confused: But now what?

I gotta get back on it, I got to get me some rubber magnets too.

Then there is the wood and I really do believe that the key to
many possible designs using cancellation will bring about an O.U.
condition.

Like your discourse on how hard it is to keep those magnets in
place where they made to sit shows very powerful forces at work.

If we looked at your roller under the magnetic film viewer we
might be able to see what is going on there, such as the field
energy shifting out ward toward the north due to all of the
mechanical on going stress.

You got me runnin now.:thumbsup: Thanks Dave, you are awesome.

BroMikey
01-08-2016, 10:29 PM
1 watt in and way more out.100hp in and 150hp out.

https://www.youtube.com/watch?v=mq98r-rdayo

SisMika
01-08-2016, 10:44 PM
You sure do like to post videos that make a lot of claims with nothing to back them up. There are never any real measurements taken in that video. Just a couple with a lot assumptions and foolishness about the rest. That same guy has been proven to be a fake by several people.
WHY DO YOU KEEP POSTING THE SAME JUNK OVER AND OVER?

BroMikey
01-09-2016, 01:19 AM
The reason I repost and comment on certain video's is because
of the response everyone gives back. Your comments always
demand the use of amp burning measuring tools when the device
continues to run.

This shows me you have not been around long, not long enough
to have heard from all of the inventors of real free energy machines.
They all say that the kind of energy we are tapping can not always
be measured with meters.

Then the new guys get mad, storm off calling everyone names
and still haven't got the message yet.

Where is your meter reading? You keep asking?:D

See I got you again. When will you ever hear this message?
When will you open your minds to receive that idea?

You are told that a motor generator scheme is nothing more
than a school boy fantasy so you don't try, you won't believe
that what we have been taught is missing a great deal.

So you won't try.

Even John Bedini tells you this is the way he started, by putting
a motor and generator together trying to loop them. John B.
explained that his second step was he used only a conventional
DC motor to drive his larger rotor with the big magnets.

And it worked. You have to start with something and that something
is the will to get more out than in. The energy that I am talking
about has been tapped for decades and is not different than wind.
Just like the sun and the wind are always there, so are other energy
fields ready to be harvested.

When i first heard these words I kept asking questions til the
inventor grew tried of me asking, but after some time I finally
figured it out.

One good phrase that he always used talking about this
other form of energy, he would say, "It just shows up at the load"

This blew me away and of course I had to be sure continued my
line of conventional reasoning, like this. "So you say just shows up"
then I would add "but the wires are carrying the current"? "Right"?
"I mean you are using 100-200 amp wires right"?

He would reply, "wrong"!!:thinking:

I would reply "Well how can that be I was taught"...........?:D

And he would response that the energy is "LIKE A GAS" or my
understanding of conventional wisdom he would say
"Like an ultra High Voltage that doesn't carry much current at all"

HUH?:suprise: How can that be?

Another inventor I know was explaining the same concept when he
kept burning out 400 amp capable golf cart controllers, melting
them like butter in a run away avalanche. His source could not have
possibly done that because all he was working with was a TPU running
at a few hundred watts, I think around 500 watts.

We figured it out by 24vdc X 200amps = 4800 watts and he smoked
400 amp units.

You tell me what to think.:thinking:

BroMikey
04-30-2016, 09:43 AM
New progress from beginner who did the work.

Even a new guy can win.

https://www.youtube.com/watch?v=8RZB1xstXS0

BroMikey
09-17-2016, 09:41 AM
Free Energy, it's all around us and in fact we're bathing in it

Literally. Amigo's, your new motor is finally here.

:rofl:

https://www.youtube.com/watch?v=VonUp5Wicwk

BroMikey
02-27-2017, 08:33 AM
Permanent Magnet Motor/ Engine
Many many moons ago.

https://www.youtube.com/watch?v=l4O44Io4gTs (https://www.youtube.com/watch?v=l4O44Io4gTs)
https://i.ytimg.com/vi/073ZZvWYyx4/hqdefault.jpg

BroMikey
03-04-2017, 04:44 AM
Chris Wojtowicz Permanent Magnet Motor

https://www.youtube.com/watch?v=kSQNp0qlUGE (https://www.youtube.com/watch?v=kSQNp0qlUGE)
https://i.ytimg.com/vi/yrD_TYpXnsc/0.jpg

BroMikey
03-04-2017, 10:49 PM
Today we are blessed to have better ways to illustrate invention
some may say that 80 years to achieve this is a bit to long. I say
better late than never on this 1929 patent. Once any process can
be clearly shown, the next stepping stone can be had much more
quickly.

I my case, I am 60 years old and this is the first time I have ever
seen anything so clearly presented in a matter of minutes if not
seconds.

Decades is unacceptable. Unsatisfactory is another expression that
we should be using when research data is incomplete for generations.

The days of suppression of the people are ending with the rise of the
individual who can learn to keep open files before the public eye.

The web was intended to be used exclusively as a tool to bring about
a world wide web control grid to imprison mankind under the iron hand
of dictatorial bullies.

Whenever people lay traps for others, remember this,
THEY WILL FALL INTO THAT TRAP.:thumbsup:

Thanks MARIO, thanks for taking out your time to help me understand.


HARRY WORTHINGTON Magnetic Motor
https://www.youtube.com/watch?v=KAUL9SXGvtQ (https://www.youtube.com/watch?v=KAUL9SXGvtQ)
https://s3.amazonaws.com/lowres.cartoonstock.com/health-beauty-invention-inventor-back_scratcher-itch-itching-ptr0166_low.jpg

BroMikey
03-04-2017, 10:56 PM
Johannes Reinhold Permanent Magnet Motor
https://www.youtube.com/watch?v=mmuYHj_kJqU (https://www.youtube.com/watch?v=mmuYHj_kJqU)

http://www.picgifs.com/job-graphics/job-graphics/inventor/uitvinder07.gif

BroMikey
03-04-2017, 11:38 PM
Johannes Reinhold Permanent Magnet Motor

https://www.youtube.com/watch?v=mmuYHj_kJqU (https://www.youtube.com/watch?v=mmuYHj_kJqU)

http://imageenvision.com/450/24403-clip-art-graphic-of-a-yellow-electric-lightbulb-cartoon-character-talking-to-a-business-man-by-toons4biz.jpg

BroMikey
03-04-2017, 11:49 PM
Mike Brady Permanent Magnet Machine


https://www.youtube.com/watch?v=WYEwZx9BwJ4 (https://www.youtube.com/watch?v=WYEwZx9BwJ4)

https://s3.amazonaws.com/lowres.cartoonstock.com/accountants-roundabout-park-playground-play_ground-renewable_energy-mfln7948_low.jpg

BroMikey
04-09-2017, 06:59 AM
Hello to our bright lights of invention. This share comes with
magnetic gating data via experimentation. Enjoy the ride, I am.


https://www.youtube.com/watch?v=iz_UhZYRMb8 (https://www.youtube.com/watch?v=iz_UhZYRMb8)
https://ytimg.googleusercontent.com/vi/iz_UhZYRMb8/mqdefault.jpg

BroMikey
04-09-2017, 07:07 AM
Great video to advance and propel our beginners into a
working device. So much has been collected. Howard Johnson
helped us a great deal.

https://www.youtube.com/watch?v=cygLBDgvE5Y (https://www.youtube.com/watch?v=cygLBDgvE5Y)
http://overunity.com/mft/Image5.gif